I
itsrico
Grünschnabel
Hallo, erste Schritte mit Linux waren gut. Drei Dinge nerven :
1
Der Rechner bootet nicht von der Festplatte.
2
Die swap-Partition wird nicht genutzt.
3
Die Netzwerkkarte muß nach jedem Start eingelesen werden.
Habe Suse Linux 9.3 von der Eval-DVD.
Partitionen (kein zweites Betriebssystem):
/dev/sda1 /boot
2 /root
3
4 /backup
5 /swap
6 /home
7 /usr
8 /var
9 /opt
Beim Einschalten des Rechners ist die DVD eingelegt. Die Fehlermeldung lautet:
Failed to boot from Hard Disk.
Die Datei menu.lst sieht so aus:
----------------------------------------------------------------------------------------------------
menu.lst:
# Modified by YaST2. Last modification on So Sep 25 14:55:08 CEST 2005
color white/blue black/light-gray
default 0
timeout 8
gfxmenu (hd0,0)/message
###Don't change this comment - YaST2 identifier: Original name: linux###
title LINUX
kernel (hd0,0)/boot/vmlinuz root=/dev/sda2 vga=0x317 selinux=0 splash=silent console=tty0 showopts
initrd (hd0,0)/boot/initrd
###Don't change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- SUSE LINUX 9.3
kernel (hd0,0)/vmlinuz root=/dev/sda2 showopts ide=nodma apm=off acpi=off vga=normal noresume selinux=0 barrier=off iommu=noforce 3
initrd (hd0,0)/initrd
--------------------------------------------------------------------------------------------------------
In der Suse-Hilfe bin ich nicht fündig geworden. Wisst ihr einen Rat?
Ich sag schon mal schönen Dank!
Rico
1
Der Rechner bootet nicht von der Festplatte.
2
Die swap-Partition wird nicht genutzt.
3
Die Netzwerkkarte muß nach jedem Start eingelesen werden.
Habe Suse Linux 9.3 von der Eval-DVD.
Partitionen (kein zweites Betriebssystem):
/dev/sda1 /boot
2 /root
3
4 /backup
5 /swap
6 /home
7 /usr
8 /var
9 /opt
Beim Einschalten des Rechners ist die DVD eingelegt. Die Fehlermeldung lautet:
Failed to boot from Hard Disk.
Die Datei menu.lst sieht so aus:
----------------------------------------------------------------------------------------------------
menu.lst:
# Modified by YaST2. Last modification on So Sep 25 14:55:08 CEST 2005
color white/blue black/light-gray
default 0
timeout 8
gfxmenu (hd0,0)/message
###Don't change this comment - YaST2 identifier: Original name: linux###
title LINUX
kernel (hd0,0)/boot/vmlinuz root=/dev/sda2 vga=0x317 selinux=0 splash=silent console=tty0 showopts
initrd (hd0,0)/boot/initrd
###Don't change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- SUSE LINUX 9.3
kernel (hd0,0)/vmlinuz root=/dev/sda2 showopts ide=nodma apm=off acpi=off vga=normal noresume selinux=0 barrier=off iommu=noforce 3
initrd (hd0,0)/initrd
--------------------------------------------------------------------------------------------------------
In der Suse-Hilfe bin ich nicht fündig geworden. Wisst ihr einen Rat?
Ich sag schon mal schönen Dank!
Rico