Bootdata ok (command line is root=/dev/sda9 vga=0x317 resume=/dev/sda8 splash=silent)
Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000037fb0000 (usable)
BIOS-e820: 0000000037fb0000 - 0000000037fc0000 (ACPI data)
BIOS-e820: 0000000037fc0000 - 0000000037ff0000 (ACPI NVS)
BIOS-e820: 0000000037ff0000 - 0000000038000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
DMI present.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa870
ACPI: RSDT (v001 A_M_I OEMRSDT 0x03000703 MSFT 0x00000097) @ 0x0000000037fb0000
ACPI: FADT (v002 A M I OEMFACP 0x12000601 MSFT 0x00000097) @ 0x0000000037fb0200
ACPI: MADT (v001 A_M_I OEMAPIC 0x03000703 MSFT 0x00000097) @ 0x0000000037fb0390
ACPI: MCFG (v001 A_M_I OEMMCFG 0x03000703 MSFT 0x00000097) @ 0x0000000037fb0400
ACPI: OEMB (v001 A_M_I AMI_OEM 0x03000703 MSFT 0x00000097) @ 0x0000000037fc0040
ACPI: SSDT (v001 A M I POWERNOW 0x00000001 AMD 0x00000001) @ 0x0000000037fb5030
ACPI: DSDT (v001 AM2N6 AM2N6201 0x00000201 INTL 0x20051117) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 0000000037fb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-0000000037fb0000
On node 0 totalpages: 225016
DMA zone: 2894 pages, LIFO batch:0
DMA32 zone: 222122 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 38000000:c6c00000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
Built 1 zonelists. Total pages: 225016
Kernel command line: root=/dev/sda9 vga=0x317 resume=/dev/sda8 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2411.021 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ e80a000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 894976k/917184k available (1915k kernel code, 21820k reserved, 1278k data, 188k init)
Calibrating delay using timer specific routine.. 4826.93 BogoMIPS (lpj=9653867)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 3390k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12557439
Detected 12.557 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:0d.0
PCI: Transparent bridge - 0000:00:04.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:09.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1233416229.444:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:09.0 to 64
pcie_portdrv_probe->Dev[03e8:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:09.0:pcie00]
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 6144k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 bytes,<6>...found (1024x768, 46202 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 188k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
NFORCE-MCP61: IDE controller at PCI slot 0000:00:06.0
NFORCE-MCP61: chipset revision 162
NFORCE-MCP61: not 100% native mode: will probe irqs later
NFORCE-MCP61: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-H12N, ATAPI CD/DVD-ROM drive
hdb: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 2.00 loaded.
sata_nv 0000:00:08.0: version 2.0
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
GSI 16 sharing vector 0xD1 and IRQ 16
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata1: SATA max UDMA/133 cmd 0xE00 ctl 0xE22 bmdma 0xD880 irq 209
ata2: SATA max UDMA/133 cmd 0xE40 ctl 0xE62 bmdma 0xD888 irq 209
scsi0 : sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA7, 390721968 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xE47
Vendor: ATA Model: SAMSUNG SP2004C Rev: VM10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: Attached scsi disk sda
BIOS EDD facility v0.16 2004-Jun-25, 4 devices found
sd 0:0:0:0: Attached scsi generic sg0 type 0
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
usbcore: registered new driver usbfs
usbcore: registered new driver hub
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
GSI 17 sharing vector 0xD9 and IRQ 17
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LMAC] -> GSI 22 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:07.0 to 64
forcedeth: using HIGHDMA
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
nvidia: module license 'NVIDIA' taints kernel.
eth0: forcedeth.c: subsystem: 01849:03ef bound to 0000:00:07.0
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
GSI 18 sharing vector 0xE1 and IRQ 18
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 21 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 225, io mem 0xdffff000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20
GSI 19 sharing vector 0xE9 and IRQ 19
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 20 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 233, io mem 0xdfffec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hda: ATAPI 126X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LMC9] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:0d.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Adding 1349388k swap on /dev/sda8. Priority:-1 extents:1 across:1349388k
usb 2-2: new high speed USB device using ehci_hcd and address 2
usb 2-2: new device found, idVendor=05e3, idProduct=0702
usb 2-2: new device strings: Mfr=2, Product=3, SerialNumber=0
usb 2-2: Product: USB Mass Storage Device
usb 2-2: Manufacturer: Genesyslogic
usb 2-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
usb 2-3: new high speed USB device using ehci_hcd and address 3
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
usb 2-3: new device found, idVendor=058f, idProduct=6390
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3: Product: USB TO IDE Bridge
usb 2-3: Manufacturer: Generic
usb 2-3: configuration #1 chosen from 1 choice
usb 2-4: new high speed USB device using ehci_hcd and address 4
usb 2-4: new device found, idVendor=152d, idProduct=2339
usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=5
usb 2-4: Product: USB to ATA/ATAPI Bridge
usb 2-4: Manufacturer: JMicron
usb 2-4: SerialNumber: DCA5194082FF
usb 2-4: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: HDT72251 Model: 6DLAT80 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
Vendor: WDC WD50 Model: 00AAJS-22TKA0 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB Disk Rev: 9.02
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sdd: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
sdc: Write Protect is off
sdc: Mode Sense: 00 38 00 00
sdc: assuming drive cache: write through
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sdd: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 38 00 00
sdc: assuming drive cache: write through
sdc:<4>sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
sdb:<5>sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
sdd: sdc1 sdc2
sd 4:0:0:0: Attached scsi disk sdc
sd 4:0:0:0: Attached scsi generic sg1 type 0
sdb1
sd 2:0:0:0: Attached scsi disk sdb
sd 2:0:0:0: Attached scsi generic sg2 type 0
sdd1
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
usb-storage: device scan complete
usb-storage: device scan complete
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
AppArmor: AppArmor initialized
audit(1233416245.029:2): AppArmor initialized
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3800+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x6
powernow-k8: 1 : fid 0xe (2200 MHz), vid 0x8
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xa
powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xc
powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
NET: Registered protocol family 17
audit(1233412677.046:3): audit_pid=4108 old=0 by auid=4294967295
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ppp0 renamed to dsl0
eth0: no IPv6 routers present
NTFS volume version 3.1.
NTFS volume version 3.1.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
NET: Registered protocol family 24
st: Version 20050830, fixed bufsize 32768, s/g segs 256
Losing some ticks... checking if CPU frequency changed.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdd1.
hfs: can't find a HFS filesystem on dev sdd1.
VFS: Can't find a Minix or Minix V2 filesystem on device sdd1
ReiserFS: sdd1: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sdd1
Unable to identify CD-ROM format.
VFS: Can't find ext3 filesystem on dev sdd1.
NTFS-fs error (device sdd1): read_ntfs_boot_sector(): Primary boot sector is invalid.
NTFS-fs error (device sdd1): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device sdd1): ntfs_fill_super(): Not an NTFS volume.
VFS: Can't find ext3 filesystem on dev sdd1.