oyster-manu
toast
hallo,
ich habe ein Problem mit der Festplatte meiner Freundin: immer wenn der PC eingeschaltet wird, brummt die festplatte extrem laut für ca. 5min. Danach sinkt der pegel wieder auf normale lautstärke ab.
Ich habe nun smartmontools durchlaufen lassen. Ich blicke allerdings nicht durch die Fehlermeldungen durch....
ich habe ein Problem mit der Festplatte meiner Freundin: immer wenn der PC eingeschaltet wird, brummt die festplatte extrem laut für ca. 5min. Danach sinkt der pegel wieder auf normale lautstärke ab.
Ich habe nun smartmontools durchlaufen lassen. Ich blicke allerdings nicht durch die Fehlermeldungen durch....
Code:
linux:~ # smartctl -a /dev/hda
[AUSZUG]
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: MAXTOR 6L040J2
Serial Number: 662205153313
Firmware Version: A93.0500
User Capacity: 40,027,029,504 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1
Local Time is: Thu May 17 22:14:03 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 16) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 35) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 573 hours (23 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 10 f7 6f 09 e0 Error: UNC at LBA = 0x00096ff7 = 618487
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 00 10 f7 6f 09 e0 09 00:01:45.503 READ MULTIPLE
c6 00 10 00 00 00 ef 09 00:01:45.502 SET MULTIPLE MODE
91 00 3f 00 00 00 af 09 00:01:45.502 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 09 00:01:45.500 RECALIBRATE [OBS-4]
ff ff ff ff ff ff ff ff 00:01:45.314 [VENDOR SPECIFIC]
Error 6 occurred at disk power-on lifetime: 573 hours (23 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 10 f7 6f 09 e0 Error: UNC at LBA = 0x00096ff7 = 618487
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 00 10 f7 6f 09 e0 09 00:01:40.303 READ MULTIPLE
c6 00 10 00 00 00 ef 09 00:01:40.302 SET MULTIPLE MODE
91 00 3f 00 00 00 af 09 00:01:40.302 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 09 00:01:40.300 RECALIBRATE [OBS-4]
ff ff ff ff ff ff ff ff 00:01:40.114 [VENDOR SPECIFIC]
Error 5 occurred at disk power-on lifetime: 573 hours (23 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 10 f7 6f 09 e0 Error: UNC at LBA = 0x00096ff7 = 618487
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 00 10 f7 6f 09 e0 09 00:01:35.103 READ MULTIPLE
c6 00 10 00 00 00 ef 09 00:01:35.103 SET MULTIPLE MODE
91 00 3f 00 00 00 af 09 00:01:35.102 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 09 00:01:35.100 RECALIBRATE [OBS-4]
ff ff ff ff ff ff ff ff 00:01:34.914 [VENDOR SPECIFIC]
Error 4 occurred at disk power-on lifetime: 573 hours (23 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 10 f7 6f 09 e0 Error: UNC at LBA = 0x00096ff7 = 618487
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 00 10 f7 6f 09 e0 09 00:01:29.903 READ MULTIPLE
c6 00 10 00 00 00 ef 09 00:01:29.902 SET MULTIPLE MODE
91 00 3f 00 00 00 af 09 00:01:29.902 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 09 00:01:29.900 RECALIBRATE [OBS-4]
ff ff ff ff ff ff ff ff 00:01:29.723 [VENDOR SPECIFIC]
Error 3 occurred at disk power-on lifetime: 573 hours (23 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 10 f7 6f 09 e0 Error: UNC at LBA = 0x00096ff7 = 618487
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 00 10 f7 6f 09 e0 09 00:01:24.708 READ MULTIPLE
c4 00 10 e7 6f 09 e0 09 00:01:24.703 READ MULTIPLE
c6 00 10 00 00 00 ef 09 00:01:24.702 SET MULTIPLE MODE
91 00 3f 00 00 00 af 09 00:01:24.702 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 09 00:01:24.700 RECALIBRATE [OBS-4]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Abort offline test Aborted by host 00% 5360 -
# 2 Abort offline test Aborted by host 00% 5360 -
# 3 Short offline Completed without error 00% 5359 -
# 4 Abort offline test Aborted by host 70% 5359 -
# 5 Abort offline test Aborted by host 30% 5359 -
# 6 Abort offline test Aborted by host 00% 5359 -
# 7 Extended offline Completed without error 00% 5359 -
# 8 Short offline Completed without error 00% 2693 -
Device does not support Selective Self Tests/Logging