Router crash bei Fedora 15!?

G

Gast1

Gast
Hi

Ich habe ein merkwürdiges Problem :think:

Ich habe ein Netbook mit Fedora 15 32Bit und ein Laptop mit Fedora 15 als 64Bit version.

Zu Hause komme ich mit beiden Rechnern Problemlos ins LAN, wobei ich dort mit dem Laptop am Kabel hänge.

Bei meinen Eltern habe ich das Problem, dass wenn ich mit dem Laptop per WLAN ins Netwerk gehe, und dann eine internetverbindung aufbaue, der Router crasht.
Mit meinem Netbook, welches ich gerade nutze, ist das kein Problem. Mit dem Laptop komme ich auch kurz ins netz, etwa 1 Minute, dann geht die Verbindung verloren (für alle im LAN)

Warum crasht also der Router wenn ich mit dem Laptop ins Internet gehe? (Telekom-Router, etwa 3/4 Jahr alt)
Wo muss ich nach dem Problem suchen?

Auszüge aus /var/log/messages
Nach dem einschalten des WLANs an meinem Laptop
Code:
Aug 20 13:30:43 john ntpd_intres[1002]: host name not found: 0.fedora.pool.ntp.org
Aug 20 13:30:43 john ntpd_intres[1002]: host name not found: 1.fedora.pool.ntp.org
Aug 20 13:30:43 john ntpd_intres[1002]: host name not found: 2.fedora.pool.ntp.org
Aug 20 13:30:43 john ntpd_intres[1002]: host name not found: 3.fedora.pool.ntp.org
Aug 20 13:31:16 john dbus: [system] Activating service name='org.freedesktop.PackageKit' (using servicehelper)
Aug 20 13:31:16 john dbus: [system] Successfully activated service 'org.freedesktop.PackageKit'
Aug 20 13:31:47 john kernel: [ 8690.213000] iwlagn 0000:02:00.0: RF_KILL bit toggled to enable radio.
Aug 20 13:31:47 john NetworkManager[1010]: <info> WiFi now enabled by radio killswitch
Aug 20 13:31:47 john NetworkManager[1010]: <info> (wlan0): bringing up device.
Aug 20 13:31:48 john kernel: [ 8690.386128] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Aug 20 13:31:48 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: starting -> ready
Aug 20 13:31:48 john NetworkManager[1010]: <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
Aug 20 13:31:48 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: ready -> inactive
Aug 20 13:31:48 john lldpad[1231]: evb_ifdown:port wlan0 remove failed
Aug 20 13:31:48 john lldpad[1231]: vdp_ifdown:wlan0 vdp data remove failed
Aug 20 13:31:48 john kernel: [ 8690.786522] usb 2-1.7: new full speed USB device number 7 using ehci_hcd
Aug 20 13:31:48 john kernel: [ 8690.875563] usb 2-1.7: New USB device found, idVendor=03f0, idProduct=231d
Aug 20 13:31:48 john kernel: [ 8690.875571] usb 2-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Aug 20 13:31:48 john kernel: [ 8690.875578] usb 2-1.7: Product: HP Integrated Module
Aug 20 13:31:48 john kernel: [ 8690.875583] usb 2-1.7: Manufacturer: Broadcom Corp
[bluetooth-zeugs]
Aug 20 13:31:51 john NetworkManager[1010]: <info> Auto-activating connection 'NAME'.
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) starting connection 'NAME'
Aug 20 13:31:51 john NetworkManager[1010]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Aug 20 13:31:51 john NetworkManager[1010]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0/wireless): access point 'NAME' has security, but secrets are required.
Aug 20 13:31:51 john NetworkManager[1010]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Aug 20 13:31:51 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Aug 20 13:31:52 john NetworkManager[1010]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Aug 20 13:31:52 john NetworkManager[1010]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0/wireless): connection 'NAME' has security, and secrets exist.  No new secrets needed.
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: added 'ssid' value 'NAME'
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: added 'scan_ssid' value '1'
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: added 'psk' value '<omitted>'
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: added 'proto' value 'WPA RSN'
Aug 20 13:31:52 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Aug 20 13:31:52 john NetworkManager[1010]: <info> Config: set interface ap_scan to 1
Aug 20 13:31:52 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: inactive -> scanning
Aug 20 13:31:54 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Aug 20 13:31:54 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: authenticating -> associating
Aug 20 13:31:54 john kernel: [ 8697.241042] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Aug 20 13:31:54 john kernel: [ 8697.241220] cfg80211: Calling CRDA for country: DE
Aug 20 13:31:54 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: associating -> associated
Aug 20 13:31:54 john kernel: [ 8697.276428] cfg80211: Regulatory domain changed to country: DE
Aug 20 13:31:54 john kernel: [ 8697.276431] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Aug 20 13:31:54 john kernel: [ 8697.276434] cfg80211:     (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:31:54 john kernel: [ 8697.276436] cfg80211:     (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:31:54 john kernel: [ 8697.276438] cfg80211:     (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:31:54 john kernel: [ 8697.276440] cfg80211:     (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
Aug 20 13:31:56 john avahi-daemon[991]: Registering new address record for fe80::223:14ff:fe8b:f1b8 on wlan0.*.
Aug 20 13:31:58 john ntpd[1000]: Listen normally on 4 wlan0 fe80::223:14ff:fe8b:f1b8 UDP 123
Aug 20 13:31:58 john ntpd[1000]: peers refreshed
Aug 20 13:31:58 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: associated -> 4-way handshake
Aug 20 13:31:58 john lldpad[1231]: vdp_ifup:wlan0 vdp data already exists !
Aug 20 13:31:58 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: 4-way handshake -> completed
Aug 20 13:31:58 john NetworkManager[1010]: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network 'NAME'.
Aug 20 13:31:58 john NetworkManager[1010]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
Aug 20 13:31:58 john NetworkManager[1010]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
Aug 20 13:31:58 john NetworkManager[1010]: <info> (wlan0): device state change: config -> ip-config (reason 'none') [50 70 0]
Aug 20 13:31:58 john NetworkManager[1010]: <info> Activation (wlan0) Beginning DHCPv4 transaction (timeout in 45 seconds)
Aug 20 13:31:58 john NetworkManager[1010]: <info> dhclient started with pid 4174
Aug 20 13:31:58 john NetworkManager[1010]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
Aug 20 13:31:59 john dhclient[4174]: Internet Systems Consortium DHCP Client 4.2.1-P1
Aug 20 13:31:59 john dhclient[4174]: Copyright 2004-2011 Internet Systems Consortium.
Aug 20 13:31:59 john dhclient[4174]: All rights reserved.
Aug 20 13:31:59 john dhclient[4174]: For info, please visit https://www.isc.org/software/dhcp/
Aug 20 13:31:59 john dhclient[4174]: 
Aug 20 13:31:59 john NetworkManager[1010]: <info> (wlan0): DHCPv4 state changed nbi -> preinit
Aug 20 13:31:59 john dhclient[4174]: Listening on LPF/wlan0/00:23:14:8b:f1:b8
Aug 20 13:31:59 john dhclient[4174]: Sending on   LPF/wlan0/00:23:14:8b:f1:b8
Aug 20 13:31:59 john dhclient[4174]: Sending on   Socket/fallback
Aug 20 13:31:59 john dhclient[4174]: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Aug 20 13:31:59 john dhclient[4174]: DHCPACK from 192.168.1.1
Aug 20 13:31:59 john dhclient[4174]: bound to 192.168.1.150 -- renewal in 746586 seconds.
Aug 20 13:31:59 john NetworkManager[1010]: <info> (wlan0): DHCPv4 state changed preinit -> reboot
Aug 20 13:31:59 john NetworkManager[1010]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) scheduled...
Aug 20 13:31:59 john NetworkManager[1010]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) started...
Aug 20 13:31:59 john NetworkManager[1010]: <info>   address 192.168.1.150
Aug 20 13:31:59 john NetworkManager[1010]: <info>   prefix 24 (255.255.255.0)
Aug 20 13:31:59 john NetworkManager[1010]: <info>   gateway 192.168.1.1
Aug 20 13:31:59 john NetworkManager[1010]: <info>   nameserver '192.168.1.1'
Aug 20 13:31:59 john NetworkManager[1010]: <info>   domain name 'Speedport_W_504V_Typ_A'
Aug 20 13:31:59 john NetworkManager[1010]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) scheduled...
Aug 20 13:31:59 john NetworkManager[1010]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) complete.
Aug 20 13:31:59 john NetworkManager[1010]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) started...
Aug 20 13:31:59 john avahi-daemon[991]: Joining mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.150.
Aug 20 13:31:59 john avahi-daemon[991]: New relevant interface wlan0.IPv4 for mDNS.
Aug 20 13:31:59 john avahi-daemon[991]: Registering new address record for 192.168.1.150 on wlan0.IPv4.
Aug 20 13:32:00 john ntpd_intres[1002]: host name not found: 0.fedora.pool.ntp.org
Aug 20 13:32:00 john ntpd_intres[1002]: host name not found: 1.fedora.pool.ntp.org
Aug 20 13:32:00 john ntpd_intres[1002]: host name not found: 2.fedora.pool.ntp.org
Aug 20 13:32:00 john ntpd_intres[1002]: host name not found: 3.fedora.pool.ntp.org
Aug 20 13:32:00 john NetworkManager[1010]: <info> (wlan0): device state change: ip-config -> activated (reason 'none') [70 100 0]
Aug 20 13:32:00 john NetworkManager[1010]: <info> Policy set 'NAME' (wlan0) as default for IPv4 routing and DNS.
Aug 20 13:32:00 john NetworkManager[1010]: <info> Activation (wlan0) successful, device activated.
Aug 20 13:32:00 john NetworkManager[1010]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete.
Aug 20 13:32:00 john dbus: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper)
Aug 20 13:32:00 john dbus: [system] Successfully activated service 'org.freedesktop.nm_dispatcher'
Aug 20 13:32:01 john ntpd[1000]: Listen normally on 5 wlan0 192.168.1.150 UDP 123
Aug 20 13:32:01 john ntpd[1000]: peers refreshed
Aug 20 13:32:04 john ntpd_intres[1002]: DNS 0.fedora.pool.ntp.org -> 85.236.42.140
Aug 20 13:32:05 john ntpd_intres[1002]: DNS 1.fedora.pool.ntp.org -> 95.89.157.176
Aug 20 13:32:05 john ntpd_intres[1002]: DNS 2.fedora.pool.ntp.org -> 131.188.3.220
Aug 20 13:32:06 john ntpd_intres[1002]: DNS 3.fedora.pool.ntp.org -> 129.70.132.34
Aug 20 13:32:10 john ntpd[1000]: 0.0.0.0 c615 05 clock_sync
Aug 20 13:32:18 john dbus: [system] Activating service name='net.reactivated.Fprint' (using servicehelper)
Aug 20 13:32:18 john dbus: [system] Successfully activated service 'net.reactivated.Fprint'

Soweit alles OK, Verbindung steht. Wenn ich jetzt einen Browser starte, und websites ansurfe kommen folgende einträge hinzu:
(Ein teil der Seiten wird ganz, oder teilweise geladen, nach kurzer Zeit ist dann aber schluss)
Code:
Aug 20 13:34:19 john kernel: [ 8841.785233] iwlagn 0000:02:00.0: Aggregation not enabled for tid 0 because load = 0
Aug 20 13:34:22 john kernel: [ 8844.947073] iwlagn 0000:02:00.0: iwlagn_tx_agg_start on ra = 00:26:4d:a3:b0:5e tid = 0
Aug 20 13:34:23 john kernel: [ 8845.993222] iwlagn 0000:02:00.0: Stopping AGG while state not ON or starting
Aug 20 13:34:23 john kernel: [ 8846.046109] cfg80211: Calling CRDA to update world regulatory domain
Aug 20 13:34:23 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: completed -> disconnected
Aug 20 13:34:23 john kernel: [ 8846.096752] cfg80211: World regulatory domain updated:
Aug 20 13:34:23 john kernel: [ 8846.096759] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Aug 20 13:34:23 john kernel: [ 8846.096766] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.096773] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.096779] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.096785] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.096791] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.096815] cfg80211: Calling CRDA for country: DE
Aug 20 13:34:23 john kernel: [ 8846.103563] cfg80211: Regulatory domain changed to country: DE
Aug 20 13:34:23 john kernel: [ 8846.103569] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Aug 20 13:34:23 john kernel: [ 8846.103576] cfg80211:     (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.103582] cfg80211:     (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.103588] cfg80211:     (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Aug 20 13:34:23 john kernel: [ 8846.103593] cfg80211:     (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
Aug 20 13:34:23 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Aug 20 13:34:39 john NetworkManager[1010]: <warn> (wlan0): link timed out.
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: activated -> disconnected (reason 'supplicant-timeout') [100 30 11]
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): deactivating device (reason: 11).
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): canceled DHCP transaction, DHCP client pid 4174
Aug 20 13:34:39 john avahi-daemon[991]: Withdrawing address record for 192.168.1.150 on wlan0.
Aug 20 13:34:39 john avahi-daemon[991]: Leaving mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.150.
Aug 20 13:34:39 john avahi-daemon[991]: Interface wlan0.IPv4 no longer relevant for mDNS.
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Aug 20 13:34:39 john NetworkManager[1010]: <info> Auto-activating connection 'NAME'.
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) starting connection 'NAME'
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Aug 20 13:34:39 john dbus: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper)
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0/wireless): access point 'NAME' has security, but secrets are required.
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Aug 20 13:34:39 john dbus: [system] Successfully activated service 'org.freedesktop.nm_dispatcher'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Aug 20 13:34:39 john NetworkManager[1010]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0/wireless): connection 'NAME' has security, and secrets exist.  No new secrets needed.
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: added 'ssid' value 'NAME'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: added 'scan_ssid' value '1'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: added 'psk' value '<omitted>'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: added 'proto' value 'WPA RSN'
Aug 20 13:34:39 john NetworkManager[1010]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Aug 20 13:34:39 john NetworkManager[1010]: <info> Config: set interface ap_scan to 1
Aug 20 13:34:40 john ntpd[1000]: Deleting interface #5 wlan0, 192.168.1.150#123, interface stats: received=32, sent=32, dropped=0, active_time=159 secs
Aug 20 13:34:40 john ntpd[1000]: 129.70.132.34 interface 192.168.1.150 -> (none)
Aug 20 13:34:40 john ntpd[1000]: 131.188.3.220 interface 192.168.1.150 -> (none)
Aug 20 13:34:40 john ntpd[1000]: 95.89.157.176 interface 192.168.1.150 -> (none)
Aug 20 13:34:40 john ntpd[1000]: 85.236.42.140 interface 192.168.1.150 -> (none)
Aug 20 13:34:40 john ntpd[1000]: peers refreshed
Aug 20 13:34:42 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Aug 20 13:35:05 john NetworkManager[1010]: <warn> Activation (wlan0/wireless): association took too long.
Aug 20 13:35:05 john NetworkManager[1010]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Aug 20 13:35:05 john NetworkManager[1010]: <warn> Activation (wlan0/wireless): asking for new secrets
Aug 20 13:35:05 john NetworkManager[1010]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Aug 20 13:35:05 john NetworkManager[1010]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Aug 20 13:35:05 john NetworkManager[1010]: <info> (wlan0): supplicant interface state: scanning -> inactive
 
Zuletzt bearbeitet von einem Moderator:
G

Gast1

Gast
So, Ich bin nun zu Hause und habe mich dort auch mal per WLAN verbunden. Hier Funktioniert alles Bestens - Natürlich, ich hätte ja auch mal intensiver nachforschen können :(
Ich habe hier ebenfalls einen Telekom-router, allerdings ein etwas älteres Modell. (W701V)

Der einzige unterschied ist nun die Verschlüsselung. Hier bin ich per WPA im WLAN, bei meinen Eltern ist es WPA2

Es liegt also entweder an dem Router meiner Eltern, oder an der WPA2 Implementierung von Fedora 15 in Verbindung mit den WLAN-Treibern, da die Treiber mit WPA funktionieren, und WPA2 auf meinem Netbook unter Fedora 15 ebenfalls läuft…
Es wird immer merkwürdiger :D

---
ps.: Wäre schön wenn der Thread nach (größeren) Änderungen so markiert würde, als wenn jemand geantwortet hat, da durch die Änderung neue Informationen hinzugekommen sind die möglicherweise jemandem helfen das Problem zu erkennen welcher zuvor genau so Ratlos war wie ich.
 
Zuletzt bearbeitet von einem Moderator:

Ähnliche Themen

VPN verbindet nichtmehr

Fedora 20 - Unlösbare Paket-Duplikat Konflikte

Rollei Mini Wifi Camcorder

LIDL-Surf-Stick Huawei E 1550 an CentOs 6.2

Druckerproblem wegen ghostscript. Tortz lösung läuft nichts.

Oben