smartctl version 5.36 [i486-slackware-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE family
Device Model: WDC WD800JB-00JJC0
Serial Number: WD-WCAM9U563811
Firmware Version: 05.01C05
User Capacity: 80.026.361.856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jun 21 21:16:48 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (2460) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 35) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 183 173 021 Pre-fail Always - 1808
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 343
5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4431
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 340
194 Temperature_Celsius 0x0022 118 095 000 Old_age Always - 25
196 Reallocated_Event_Count 0x0032 199 199 000 Old_age Always - 1
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 20 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 20 occurred at disk power-on lifetime: 4407 hours (183 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 8a 92 b3 f1 Error: UNC 2 sectors at LBA = 0x01b3928a = 28545674
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 8a 92 b3 01 59 1d+03:50:24.010 READ DMA
c8 00 04 88 92 b3 01 59 1d+03:50:21.910 READ DMA
ca 00 08 7b 20 12 00 59 1d+03:50:21.910 WRITE DMA
ca 00 28 53 20 12 00 59 1d+03:50:21.910 WRITE DMA
ca 00 10 f3 92 34 00 59 1d+03:50:21.910 WRITE DMA
Error 19 occurred at disk power-on lifetime: 4407 hours (183 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 8a 92 b3 f1 Error: UNC 2 sectors at LBA = 0x01b3928a = 28545674
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 88 92 b3 01 59 1d+03:50:21.910 READ DMA
ca 00 08 7b 20 12 00 59 1d+03:50:21.910 WRITE DMA
ca 00 28 53 20 12 00 59 1d+03:50:21.910 WRITE DMA
ca 00 10 f3 92 34 00 59 1d+03:50:21.910 WRITE DMA
c8 00 02 8a 92 b3 01 59 1d+03:50:19.995 READ DMA
Error 18 occurred at disk power-on lifetime: 4407 hours (183 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 8a 92 b3 f1 Error: UNC 2 sectors at LBA = 0x01b3928a = 28545674
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 8a 92 b3 01 59 1d+03:50:19.995 READ DMA
c8 00 04 88 92 b3 01 59 1d+03:50:17.725 READ DMA
ca 00 08 4b 20 12 00 59 1d+03:50:17.725 WRITE DMA
ca 00 10 3b 20 12 00 59 1d+03:50:17.725 WRITE DMA
ca 00 10 f3 92 34 00 59 1d+03:50:21.910 WRITE DMA
Error 17 occurred at disk power-on lifetime: 4407 hours (183 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 8a 92 b3 f1 Error: UNC 2 sectors at LBA = 0x01b3928a = 28545674
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 88 92 b3 01 59 1d+03:50:17.725 READ DMA
ca 00 08 4b 20 12 00 59 1d+03:50:17.725 WRITE DMA
ca 00 10 3b 20 12 00 59 1d+03:50:17.725 WRITE DMA
ca 00 08 f3 92 34 00 59 1d+03:50:17.725 WRITE DMA
c8 00 02 8a 92 b3 01 59 1d+03:50:15.820 READ DMA
Error 16 occurred at disk power-on lifetime: 4407 hours (183 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 8a 92 b3 f1 Error: WP at LBA = 0x01b3928a = 28545674
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 f3 92 34 00 59 1d+03:50:17.725 WRITE DMA
c8 00 02 8a 92 b3 01 59 1d+03:50:15.820 READ DMA
c8 00 04 88 92 b3 01 59 1d+03:50:13.425 READ DMA
ca 00 08 33 20 12 00 59 1d+03:50:13.425 WRITE DMA
ca 00 10 23 20 12 00 59 1d+03:50:13.420 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 4412 28545674
# 2 Extended offline Completed: read failure 90% 4406 28545674
# 3 Extended offline Aborted by host 10% 1160 -
# 4 Short offline Completed without error 00% 1160 -
# 5 Extended offline Completed without error 00% 519 -
# 6 Conveyance offline Completed without error 00% 519 -
# 7 Short offline Completed without error 00% 519 -
# 8 Extended offline Completed without error 00% 7 -
# 9 Conveyance offline Completed without error 00% 6 -
#10 Short offline Completed without error 00% 6 -
#11 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
