D
drumking
Grünschnabel
Hi Leute,
ich hab ein problem...
Ich hab mir eine Gigabit Netzwerkkarte gekauft (D-LINK DGE-528T), diese wird jedoch nicht erkannt...
ich weiß nicht wo der Fehler liegt, kann mir evtl jemand helfen?
hier ein paar infos
ifconfig:
lsmod:
dmesg:
Danke für eure hilfe!
Basti
ich hab ein problem...
Ich hab mir eine Gigabit Netzwerkkarte gekauft (D-LINK DGE-528T), diese wird jedoch nicht erkannt...
ich weiß nicht wo der Fehler liegt, kann mir evtl jemand helfen?
hier ein paar infos
ifconfig:
Code:
eth0 Link encap:Ethernet Hardware Adresse 00:22:15:43:92:98
inet Adresse:192.168.3.101 Bcast:192.168.3.255 Maske:255.255.255.0
inet6-Adresse: fe80::222:15ff:fe43:9298/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:75906 errors:0 dropped:0 overruns:0 frame:0
TX packets:42872 errors:0 dropped:0 overruns:0 carrier:2
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:111902706 (111.9 MB) TX bytes:3569893 (3.5 MB)
Interrupt:29
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:116 errors:0 dropped:0 overruns:0 frame:0
TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:9624 (9.6 KB) TX bytes:9624 (9.6 KB)
virbr0 Link encap:Ethernet Hardware Adresse e2:d2:dd:f9:49:61
inet Adresse:192.168.122.1 Bcast:192.168.122.255 Maske:255.255.255.0
inet6-Adresse: fe80::e0d2:ddff:fef9:4961/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:0 (0.0 B) TX bytes:4673 (4.6 KB)
lsmod:
Code:
Module Size Used by
binfmt_misc 7960 1
ppdev 6375 0
vboxnetadp 5235 0
vboxnetflt 12242 0
vboxdrv 1768311 2 vboxnetadp,vboxnetflt
nfsd 304374 11
lockd 75079 1 nfsd
nfs_acl 2709 1 nfsd
auth_rpcgss 44516 1 nfsd
sunrpc 228264 10 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 4202 1 nfsd
ipt_MASQUERADE 1863 3
iptable_nat 4268 1
nf_nat 19286 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 12742 4 iptable_nat,nf_nat
nf_defrag_ipv4 1481 1 nf_conntrack_ipv4
xt_state 1490 1
nf_conntrack 73326 5 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4,xt_state
ipt_REJECT 2384 2
xt_tcpudp 2667 4
iptable_filter 1841 1
ip_tables 18201 2 iptable_nat,iptable_filter
x_tables 22361 6 ipt_MASQUERADE,iptable_nat,xt_state,ipt_REJECT,xt_tcpudp,ip_tables
bridge 53184 0
stp 2171 1 bridge
kvm_intel 46456 0
kvm 286527 1 kvm_intel
snd_hda_codec_atihdmi 3023 1
fbcon 39270 71
tileblit 2487 1 fbcon
font 8053 1 fbcon
bitblit 5811 1 fbcon
softcursor 1565 1 bitblit
vga16fb 12757 0
vgastate 9857 1 vga16fb
snd_hda_codec_realtek 279040 1
snd_usb_audio 92747 1
snd_usb_lib 19193 1 snd_usb_audio
snd_hda_intel 25805 2
snd_hda_codec 85759 3 snd_hda_codec_atihdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 6924 2 snd_usb_audio,snd_hda_codec
snd_pcm_oss 41394 0
snd_mixer_oss 16299 1 snd_pcm_oss
snd_pcm 87946 4 snd_usb_audio,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1782 0
snd_seq_oss 31191 0
snd_seq_midi 5829 0
snd_rawmidi 23420 2 snd_usb_lib,snd_seq_midi
snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi
usbhid 41116 0
snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
hid 83888 1 usbhid
snd_timer 23649 2 snd_pcm,snd_seq
snd_seq_device 6888 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 71283 19 snd_hda_codec_realtek,snd_usb_audio,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
radeon 744506 3
ttm 61007 1 radeon
drm_kms_helper 30742 1 radeon
asus_atk0110 10033 0
lp 9336 0
psmouse 65040 0
serio_raw 4918 0
soundcore 8052 1 snd
snd_page_alloc 8500 2 snd_hda_intel,snd_pcm
intel_agp 29319 0
parport 37160 2 ppdev,lp
drm 200288 5 radeon,ttm,drm_kms_helper
i2c_algo_bit 6024 1 radeon
ohci1394 30260 0
floppy 63156 0
atl1e 33233 0
usb_storage 50377 1
pata_marvell 3225 0
ieee1394 94771 1 ohci1394
ahci 38030 0
dmesg:
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-34-generic (buildd@yellow) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #77-Ubuntu SMP Tue Sep 13 19:39:17 UTC 2011 (Ubuntu 2.6.32-34.77-generic 2.6.32.44+drm33.19)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-34-generic root=UUID=eea06afc-ad9e-4c56-8e07-63852d91e067 ro quiet splash
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cff70000 (usable)
[ 0.000000] BIOS-e820: 00000000cff70000 - 00000000cff7e000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cff7e000 - 00000000cffd0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cffd0000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x130000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 100000000 mask FE0000000 write-back
[ 0.000000] 2 base 120000000 mask FF0000000 write-back
[ 0.000000] 3 base 0D0000000 mask FF0000000 uncachable
[ 0.000000] 4 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xcff70 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009f800 (usable)
[ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000cff70000 (usable)
[ 0.000000] modified: 00000000cff70000 - 00000000cff7e000 (ACPI data)
[ 0.000000] modified: 00000000cff7e000 - 00000000cffd0000 (ACPI NVS)
[ 0.000000] modified: 00000000cffd0000 - 00000000d0000000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] modified: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000cff70000
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] 0000000000 - 00cfe00000 page 2M
[ 0.000000] 00cfe00000 - 00cff70000 page 4k
[ 0.000000] kernel direct mapping tables up to cff70000 @ 10000-16000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000130000000
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] 0100000000 - 0130000000 page 2M
[ 0.000000] kernel direct mapping tables up to 130000000 @ 14000-1a000
[ 0.000000] RAMDISK: 3772e000 - 37fef4b9
[ 0.000000] ACPI: RSDP 00000000000faf00 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 00000000cff70000 00040 (v01 A_M_I_ OEMRSDT 06000812 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000cff70200 00084 (v02 A_M_I_ OEMFACP 06000812 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000cff70440 09647 (v01 A0993 A0993001 00000001 INTL 20060113)
[ 0.000000] ACPI: FACS 00000000cff7e000 00040
[ 0.000000] ACPI: APIC 00000000cff70390 0006C (v01 A_M_I_ OEMAPIC 06000812 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000cff70400 0003C (v01 A_M_I_ OEMMCFG 06000812 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000cff7e040 00081 (v01 A_M_I_ AMI_OEM 06000812 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000cff79a90 00038 (v01 A_M_I_ OEMHPET 06000812 MSFT 00000097)
[ 0.000000] ACPI: OSFR 00000000cff79ad0 000B0 (v01 A_M_I_ OEMOSFR 06000812 MSFT 00000097)
[ 0.000000] ACPI: SSDT 00000000cff7eb20 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20060113)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000130000000
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000130000000
[ 0.000000] NODE_DATA [0000000000015000 - 0000000000019fff]
[ 0.000000] bootmap [000000000001a000 - 000000000003ffff] pages 26
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0130000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001a30aa4] TEXT DATA BSS ==> [0001000000 - 0001a30aa4]
[ 0.000000] #3 [003772e000 - 0037fef4b9] RAMDISK ==> [003772e000 - 0037fef4b9]
[ 0.000000] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #5 [0001a31000 - 0001a31270] BRK ==> [0001a31000 - 0001a31270]
[ 0.000000] #6 [0000010000 - 0000014000] PGTABLE ==> [0000010000 - 0000014000]
[ 0.000000] #7 [0000014000 - 0000015000] PGTABLE ==> [0000014000 - 0000015000]
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] [ffffea0000000000-ffffea00043fffff] PMD -> [ffff880028600000-ffff88002bffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00130000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000cff70
[ 0.000000] 0: 0x00100000 -> 0x00130000
[ 0.000000] On node 0 totalpages: 1048319
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 104 pages reserved
[ 0.000000] DMA zone: 3823 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 833448 pages, LIFO batch:31
[ 0.000000] Normal zone: 2688 pages used for memmap
[ 0.000000] Normal zone: 193920 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000cff70000 - 00000000cff7e000
[ 0.000000] PM: Registered nosave memory: 00000000cff7e000 - 00000000cffd0000
[ 0.000000] PM: Registered nosave memory: 00000000cffd0000 - 00000000d0000000
[ 0.000000] PM: Registered nosave memory: 00000000d0000000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000fff00000
[ 0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:2ee00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880028200000 s91864 r8192 d22824 u524288
[ 0.000000] pcpu-alloc: s91864 r8192 d22824 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031191
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-34-generic root=UUID=eea06afc-ad9e-4c56-8e07-63852d91e067 ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.000000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
[ 0.000000] software IO TLB at phys 0x20000000 - 0x24000000
[ 0.000000] Memory: 4047792k/4980736k available (5415k kernel code, 787460k absent, 145484k reserved, 2977k data, 888k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 41943040 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3165.878 MHz processor.
[ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 6331.75 BogoMIPS (lpj=31658780)
[ 0.000024] Security Framework initialized
[ 0.000038] AppArmor: AppArmor initialized
[ 0.000291] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.011481] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.012179] Mount-cache hash table entries: 256
[ 0.012282] Initializing cgroup subsys ns
[ 0.012286] Initializing cgroup subsys cpuacct
[ 0.012288] Initializing cgroup subsys memory
[ 0.012294] Initializing cgroup subsys devices
[ 0.012296] Initializing cgroup subsys freezer
[ 0.012297] Initializing cgroup subsys net_cls
[ 0.012313] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.012314] CPU: L2 cache: 6144K
[ 0.012317] CPU 0/0x0 -> Node 0
[ 0.012318] CPU: Physical Processor ID: 0
[ 0.012319] CPU: Processor Core ID: 0
[ 0.012321] mce: CPU supports 6 MCE banks
[ 0.012327] CPU0: Thermal monitoring enabled (TM2)
[ 0.012330] using mwait in idle threads.
[ 0.012331] Performance Events: Core2 events, Intel PMU driver.
[ 0.012336] ... version: 2
[ 0.012337] ... bit width: 40
[ 0.012338] ... generic registers: 2
[ 0.012339] ... value mask: 000000ffffffffff
[ 0.012340] ... max period: 000000007fffffff
[ 0.012341] ... fixed-purpose events: 3
[ 0.012342] ... event mask: 0000000700000003
[ 0.014189] ACPI: Core revision 20090903
[ 0.030005] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.030009] ftrace: allocating 22484 entries in 89 pages
[ 0.040035] Setting APIC routing to flat
[ 0.040326] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.153818] CPU0: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz stepping 0a
[ 0.160000] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.010000] Initializing CPU#1
[ 0.010000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.010000] CPU: L2 cache: 6144K
[ 0.010000] CPU 1/0x1 -> Node 0
[ 0.010000] CPU: Physical Processor ID: 0
[ 0.010000] CPU: Processor Core ID: 1
[ 0.010000] CPU1: Thermal monitoring enabled (TM2)
[ 0.310063] CPU1: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz stepping 0a
[ 0.310068] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.320014] Brought up 2 CPUs
[ 0.320015] Total of 2 processors activated (12664.35 BogoMIPS).
[ 0.321382] CPU0 attaching sched-domain:
[ 0.321385] domain 0: span 0-1 level MC
[ 0.321387] groups: 0 1
[ 0.321391] CPU1 attaching sched-domain:
[ 0.321392] domain 0: span 0-1 level MC
[ 0.321394] groups: 1 0
[ 0.321439] devtmpfs: initialized
[ 0.321439] regulator: core version 0.5
[ 0.321439] Time: 21:09:13 Date: 11/30/11
[ 0.321439] NET: Registered protocol family 16
[ 0.321439] Trying to unpack rootfs image as initramfs...
[ 0.321439] ACPI: bus type pci registered
[ 0.321439] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.321439] PCI: Not using MMCONFIG.
[ 0.321439] PCI: Using configuration type 1 for base access
[ 0.330049] bio: create slab <bio-0> at 0
[ 0.330634] ACPI: EC: Look up EC in DSDT
[ 0.332434] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.340611] ACPI: Interpreter enabled
[ 0.340613] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.340629] ACPI: Using IOAPIC for interrupt routing
[ 0.340668] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.342551] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.347178] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.352774] ACPI Warning: Incorrect checksum in table [OEMB] - C2, should be B9 (20090903/tbutils-314)
[ 0.352871] ACPI: No dock devices found.
[ 0.352955] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.353031] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.353033] pci 0000:00:01.0: PME# disabled
[ 0.353088] pci 0000:00:1a.0: reg 20 io port: [0xa800-0xa81f]
[ 0.353142] pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f]
[ 0.353198] pci 0000:00:1a.2: reg 20 io port: [0xac00-0xac1f]
[ 0.353255] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfe7ffc00-0xfe7fffff]
[ 0.353299] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.353302] pci 0000:00:1a.7: PME# disabled
[ 0.353334] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe7f8000-0xfe7fbfff]
[ 0.353366] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.353369] pci 0000:00:1b.0: PME# disabled
[ 0.353417] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.353420] pci 0000:00:1c.0: PME# disabled
[ 0.353470] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.353473] pci 0000:00:1c.4: PME# disabled
[ 0.353523] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.353525] pci 0000:00:1c.5: PME# disabled
[ 0.353567] pci 0000:00:1d.0: reg 20 io port: [0xa080-0xa09f]
[ 0.353621] pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f]
[ 0.353678] pci 0000:00:1d.2: reg 20 io port: [0xa480-0xa49f]
[ 0.353735] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfe7ff800-0xfe7ffbff]
[ 0.353779] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.353782] pci 0000:00:1d.7: PME# disabled
[ 0.353885] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
[ 0.353889] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 001f)
[ 0.353930] pci 0000:00:1f.2: reg 10 io port: [0x9000-0x9007]
[ 0.353934] pci 0000:00:1f.2: reg 14 io port: [0x8c00-0x8c03]
[ 0.353938] pci 0000:00:1f.2: reg 18 io port: [0x8880-0x8887]
[ 0.353942] pci 0000:00:1f.2: reg 1c io port: [0x8800-0x8803]
[ 0.353946] pci 0000:00:1f.2: reg 20 io port: [0x8480-0x848f]
[ 0.353950] pci 0000:00:1f.2: reg 24 io port: [0x8400-0x840f]
[ 0.353985] pci 0000:00:1f.3: reg 10 64bit mmio: [0xfe7ff400-0xfe7ff4ff]
[ 0.353995] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[ 0.354028] pci 0000:00:1f.5: reg 10 io port: [0xa000-0xa007]
[ 0.354032] pci 0000:00:1f.5: reg 14 io port: [0x9c00-0x9c03]
[ 0.354036] pci 0000:00:1f.5: reg 18 io port: [0x9880-0x9887]
[ 0.354041] pci 0000:00:1f.5: reg 1c io port: [0x9800-0x9803]
[ 0.354045] pci 0000:00:1f.5: reg 20 io port: [0x9480-0x948f]
[ 0.354049] pci 0000:00:1f.5: reg 24 io port: [0x9400-0x940f]
[ 0.354093] pci 0000:01:00.0: reg 10 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.354100] pci 0000:01:00.0: reg 18 64bit mmio: [0xfe8e0000-0xfe8effff]
[ 0.354104] pci 0000:01:00.0: reg 20 io port: [0xb000-0xb0ff]
[ 0.354110] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfe8c0000-0xfe8dffff]
[ 0.354124] pci 0000:01:00.0: supports D1 D2
[ 0.354150] pci 0000:01:00.1: reg 10 64bit mmio: [0xfe8fc000-0xfe8fffff]
[ 0.354179] pci 0000:01:00.1: supports D1 D2
[ 0.354213] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff]
[ 0.354215] pci 0000:00:01.0: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
[ 0.354218] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.354251] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xfdf00000-0xfdffffff]
[ 0.354289] pci 0000:03:00.0: reg 10 io port: [0xdc00-0xdc07]
[ 0.354296] pci 0000:03:00.0: reg 14 io port: [0xd880-0xd883]
[ 0.354302] pci 0000:03:00.0: reg 18 io port: [0xd800-0xd807]
[ 0.354308] pci 0000:03:00.0: reg 1c io port: [0xd480-0xd483]
[ 0.354314] pci 0000:03:00.0: reg 20 io port: [0xd400-0xd40f]
[ 0.354321] pci 0000:03:00.0: reg 24 32bit mmio: [0xfeaffc00-0xfeafffff]
[ 0.354355] pci 0000:03:00.0: supports D1
[ 0.354356] pci 0000:03:00.0: PME# supported from D0 D1 D3hot
[ 0.354360] pci 0000:03:00.0: PME# disabled
[ 0.354396] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
[ 0.354399] pci 0000:00:1c.4: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[ 0.354448] pci 0000:02:00.0: reg 10 64bit mmio: [0xfe9c0000-0xfe9fffff]
[ 0.354455] pci 0000:02:00.0: reg 18 io port: [0xcc00-0xcc7f]
[ 0.354505] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.354509] pci 0000:02:00.0: PME# disabled
[ 0.354548] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff]
[ 0.354551] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
[ 0.354580] pci 0000:05:00.0: reg 10 32bit mmio: [0xfebf0000-0xfebfffff]
[ 0.354585] pci 0000:05:00.0: reg 14 io port: [0xec00-0xec07]
[ 0.354617] pci 0000:05:00.0: PME# supported from D3hot D3cold
[ 0.354620] pci 0000:05:00.0: PME# disabled
[ 0.354648] pci 0000:05:01.0: reg 10 io port: [0xe800-0xe8ff]
[ 0.354654] pci 0000:05:01.0: reg 14 32bit mmio: [0xfebefc00-0xfebefcff]
[ 0.354674] pci 0000:05:01.0: reg 30 32bit mmio pref: [0xfebc0000-0xfebdffff]
[ 0.354690] pci 0000:05:01.0: supports D1 D2
[ 0.354691] pci 0000:05:01.0: PME# supported from D1 D2 D3hot D3cold
[ 0.354694] pci 0000:05:01.0: PME# disabled
[ 0.354721] pci 0000:05:03.0: reg 10 32bit mmio: [0xfebee000-0xfebeefff]
[ 0.354758] pci 0000:05:03.0: supports D1 D2
[ 0.354759] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.354762] pci 0000:05:03.0: PME# disabled
[ 0.354798] pci 0000:00:1e.0: transparent bridge
[ 0.354800] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
[ 0.354803] pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[ 0.354822] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.354914] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.354954] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.355031] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.355067] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.355121] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.366977] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.367058] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.367136] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.367215] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.367299] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.367378] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[ 0.367456] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.367534] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.367620] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.367623] vgaarb: loaded
[ 0.367697] SCSI subsystem initialized
[ 0.367819] libata version 3.00 loaded.
[ 0.367819] usbcore: registered new interface driver usbfs
[ 0.367826] usbcore: registered new interface driver hub
[ 0.367843] usbcore: registered new device driver usb
[ 0.367927] ACPI: WMI: Mapper loaded
[ 0.367928] PCI: Using ACPI for IRQ routing
[ 0.368057] NetLabel: Initializing
[ 0.368058] NetLabel: domain hash size = 128
[ 0.368059] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.368068] NetLabel: unlabeled traffic allowed by default
[ 0.368089] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.368092] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.368096] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.390027] Switching to clocksource tsc
[ 0.391219] AppArmor: AppArmor Filesystem Enabled
[ 0.391231] pnp: PnP ACPI init
[ 0.391251] ACPI: bus type pnp registered
[ 0.393662] pnp: PnP ACPI: found 16 devices
[ 0.393664] ACPI: ACPI bus type pnp unregistered
[ 0.393671] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 0.393676] system 00:07: ioport range 0x290-0x29f has been reserved
[ 0.393680] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.393684] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.393686] system 00:08: ioport range 0x500-0x57f has been reserved
[ 0.393688] system 00:08: iomem range 0xfed08000-0xfed08fff has been reserved
[ 0.393690] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.393691] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.393693] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
[ 0.393697] system 00:0b: iomem range 0xffc00000-0xffefffff has been reserved
[ 0.393701] system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.393703] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.393706] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.393710] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[ 0.393712] system 00:0f: iomem range 0xc0000-0xcffff has been reserved
[ 0.393714] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[ 0.393715] system 00:0f: iomem range 0x100000-0xcfffffff could not be reserved
[ 0.398378] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.398380] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.398383] pci 0000:00:01.0: MEM window: 0xfe800000-0xfe8fffff
[ 0.398385] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.398388] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
[ 0.398390] pci 0000:00:1c.0: IO window: 0x1000-0x1fff
[ 0.398394] pci 0000:00:1c.0: MEM window: 0xf0000000-0xf03fffff
[ 0.398397] pci 0000:00:1c.0: PREFETCH window: 0x000000fdf00000-0x000000fdffffff
[ 0.398401] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[ 0.398403] pci 0000:00:1c.4: IO window: 0xd000-0xdfff
[ 0.398406] pci 0000:00:1c.4: MEM window: 0xfea00000-0xfeafffff
[ 0.398409] pci 0000:00:1c.4: PREFETCH window: 0x000000f0400000-0x000000f05fffff
[ 0.398414] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02
[ 0.398416] pci 0000:00:1c.5: IO window: 0xc000-0xcfff
[ 0.398419] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff
[ 0.398422] pci 0000:00:1c.5: PREFETCH window: 0x000000f0600000-0x000000f07fffff
[ 0.398426] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.398428] pci 0000:00:1e.0: IO window: 0xe000-0xefff
[ 0.398432] pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.398434] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.398443] alloc irq_desc for 16 on node -1
[ 0.398445] alloc kstat_irqs on node -1
[ 0.398448] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.398451] pci 0000:00:01.0: setting latency timer to 64
[ 0.398456] pci 0000:00:1c.0: enabling device (0106 -> 0107)
[ 0.398459] alloc irq_desc for 17 on node -1
[ 0.398460] alloc kstat_irqs on node -1
[ 0.398462] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.398465] pci 0000:00:1c.0: setting latency timer to 64
[ 0.398470] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.398473] pci 0000:00:1c.4: setting latency timer to 64
[ 0.398479] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.398481] pci 0000:00:1c.5: setting latency timer to 64
[ 0.398486] pci 0000:00:1e.0: setting latency timer to 64
[ 0.398489] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.398491] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.398492] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.398494] pci_bus 0000:01: resource 1 mem: [0xfe800000-0xfe8fffff]
[ 0.398495] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.398497] pci_bus 0000:04: resource 0 io: [0x1000-0x1fff]
[ 0.398498] pci_bus 0000:04: resource 1 mem: [0xf0000000-0xf03fffff]
[ 0.398500] pci_bus 0000:04: resource 2 pref mem [0xfdf00000-0xfdffffff]
[ 0.398502] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
[ 0.398503] pci_bus 0000:03: resource 1 mem: [0xfea00000-0xfeafffff]
[ 0.398504] pci_bus 0000:03: resource 2 pref mem [0xf0400000-0xf05fffff]
[ 0.398506] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 0.398507] pci_bus 0000:02: resource 1 mem: [0xfe900000-0xfe9fffff]
[ 0.398509] pci_bus 0000:02: resource 2 pref mem [0xf0600000-0xf07fffff]
[ 0.398511] pci_bus 0000:05: resource 0 io: [0xe000-0xefff]
[ 0.398512] pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff]
[ 0.398513] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.398515] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.398537] NET: Registered protocol family 2
[ 0.398650] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.399472] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.402247] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.402624] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.402626] TCP reno registered
[ 0.402715] NET: Registered protocol family 1
[ 0.402845] pci 0000:01:00.0: Boot video device
[ 0.402996] Scanning for low memory corruption every 60 seconds
[ 0.403093] audit: initializing netlink socket (disabled)
[ 0.403101] type=2000 audit(1322687352.399:1): initialized
[ 0.409349] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.410269] VFS: Disk quotas dquot_6.5.2
[ 0.410304] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.410680] fuse init (API version 7.13)
[ 0.410731] msgmni has been set to 7905
[ 0.410868] alg: No test for stdrng (krng)
[ 0.410902] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.410905] io scheduler noop registered
[ 0.410906] io scheduler anticipatory registered
[ 0.410907] io scheduler deadline registered
[ 0.410928] io scheduler cfq registered (default)
[ 0.411023] alloc irq_desc for 24 on node -1
[ 0.411024] alloc kstat_irqs on node -1
[ 0.411030] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.411034] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.411102] alloc irq_desc for 25 on node -1
[ 0.411103] alloc kstat_irqs on node -1
[ 0.411108] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.411114] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.411192] alloc irq_desc for 26 on node -1
[ 0.411193] alloc kstat_irqs on node -1
[ 0.411198] pcieport 0000:00:1c.4: irq 26 for MSI/MSI-X
[ 0.411203] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.411287] alloc irq_desc for 27 on node -1
[ 0.411288] alloc kstat_irqs on node -1
[ 0.411293] pcieport 0000:00:1c.5: irq 27 for MSI/MSI-X
[ 0.411299] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.411355] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.411424] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.411502] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.411505] ACPI: Power Button [PWRB]
[ 0.411537] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.411539] ACPI: Power Button [PWRF]
[ 0.412035] ACPI: SSDT 00000000cff7e0d0 00277 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
[ 0.412359] ACPI: SSDT 00000000cff7e5d0 004B2 (v01 PmRef P001Cst 00003001 INTL 20060113)
[ 0.412686] Monitor-Mwait will be used to enter C-1 state
[ 0.412704] Monitor-Mwait will be used to enter C-2 state
[ 0.419760] Monitor-Mwait will be used to enter C-3 state
[ 0.419764] Marking TSC unstable due to TSC halts in idle
[ 0.419802] processor LNXCPU:00: registered as cooling_device0
[ 0.420104] ACPI: SSDT 00000000cff7e350 00277 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
[ 0.420333] ACPI: SSDT 00000000cff7ea90 00085 (v01 PmRef P002Cst 00003000 INTL 20060113)
[ 0.420624] processor LNXCPU:01: registered as cooling_device1
[ 0.423189] Linux agpgart interface v0.103
[ 0.423215] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.423297] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.423552] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.424212] brd: module loaded
[ 0.424514] loop: module loaded
[ 0.424565] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.424623] ata_piix 0000:00:1f.2: version 2.13
[ 0.424634] alloc irq_desc for 19 on node -1
[ 0.424635] alloc kstat_irqs on node -1
[ 0.424640] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.424643] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.424673] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.424722] scsi0 : ata_piix
[ 0.424768] scsi1 : ata_piix
[ 0.425735] ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 19
[ 0.425739] ata2: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 19
[ 0.425752] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.425755] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 0.425779] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 0.425804] scsi2 : ata_piix
[ 0.425835] scsi3 : ata_piix
[ 0.426626] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
[ 0.426629] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
[ 0.426666] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.426685] pata_acpi 0000:03:00.0: setting latency timer to 64
[ 0.426694] pata_acpi 0000:03:00.0: PCI INT A disabled
[ 0.426869] Fixed MDIO Bus: probed
[ 0.426888] PPP generic driver version 2.4.2
[ 0.426908] tun: Universal TUN/TAP device driver, 1.6
[ 0.426909] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.426960] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.426972] alloc irq_desc for 18 on node -1
[ 0.426973] alloc kstat_irqs on node -1
[ 0.426975] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.426985] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.426987] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.427012] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.427038] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.430938] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.430961] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfe7ffc00
[ 0.431125] Switching to clocksource hpet
[ 0.455600] Freeing initrd memory: 8965k freed
[ 0.461293] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.461428] usb usb1: configuration #1 chosen from 1 choice
[ 0.461448] hub 1-0:1.0: USB hub found
[ 0.461456] hub 1-0:1.0: 6 ports detected
[ 0.461509] alloc irq_desc for 23 on node -1
[ 0.461510] alloc kstat_irqs on node -1
[ 0.461516] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.461538] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.461541] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.461565] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.461593] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.465478] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.465492] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe7ff800
[ 0.481264] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.481337] usb usb2: configuration #1 chosen from 1 choice
[ 0.481361] hub 2-0:1.0: USB hub found
[ 0.481367] hub 2-0:1.0: 6 ports detected
[ 0.481427] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.481439] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.481467] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.481473] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.481475] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.481495] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.481522] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800
[ 0.481584] usb usb3: configuration #1 chosen from 1 choice
[ 0.481599] hub 3-0:1.0: USB hub found
[ 0.481604] hub 3-0:1.0: 2 ports detected
[ 0.481635] alloc irq_desc for 21 on node -1
[ 0.481636] alloc kstat_irqs on node -1
[ 0.481638] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.481642] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.481645] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.481665] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.481689] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 0.481745] usb usb4: configuration #1 chosen from 1 choice
[ 0.481760] hub 4-0:1.0: USB hub found
[ 0.481764] hub 4-0:1.0: 2 ports detected
[ 0.481794] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.481798] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 0.481800] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 0.481821] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 0.481840] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00
[ 0.481894] usb usb5: configuration #1 chosen from 1 choice
[ 0.481909] hub 5-0:1.0: USB hub found
[ 0.481913] hub 5-0:1.0: 2 ports detected
[ 0.481941] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.481945] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.481947] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.481969] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 0.481987] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080
[ 0.482047] usb usb6: configuration #1 chosen from 1 choice
[ 0.482065] hub 6-0:1.0: USB hub found
[ 0.482068] hub 6-0:1.0: 2 ports detected
[ 0.482095] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.482099] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.482101] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.482122] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 0.482141] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[ 0.482195] usb usb7: configuration #1 chosen from 1 choice
[ 0.482210] hub 7-0:1.0: USB hub found
[ 0.482215] hub 7-0:1.0: 2 ports detected
[ 0.482243] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.482247] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.482249] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.482272] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 0.482291] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480
[ 0.482347] usb usb8: configuration #1 chosen from 1 choice
[ 0.482361] hub 8-0:1.0: USB hub found
[ 0.482365] hub 8-0:1.0: 2 ports detected
[ 0.482428] PNP: No PS/2 controller found. Probing ports directly.
[ 0.485005] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.485009] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.485079] mice: PS/2 mouse device common for all mice
[ 0.485147] rtc_cmos 00:03: RTC can wake from S4
[ 0.485174] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.485194] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.485272] device-mapper: uevent: version 1.0.3
[ 0.485350] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.485403] device-mapper: multipath: version 1.1.0 loaded
[ 0.485406] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.485559] cpuidle: using governor ladder
[ 0.485627] cpuidle: using governor menu
[ 0.485852] TCP cubic registered
[ 0.485947] NET: Registered protocol family 10
[ 0.486407] NET: Registered protocol family 17
[ 0.486883] PM: Resume from disk failed.
[ 0.486892] registered taskstats version 1
[ 0.487230] Magic number: 3:132:198
[ 0.487302] rtc_cmos 00:03: setting system clock to 2011-11-30 21:09:13 UTC (1322687353)
[ 0.487305] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.487306] EDD information not available.
[ 0.800681] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.811250] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.040027] usb 2-5: new high speed USB device using ehci_hcd and address 4
[ 1.150635] ata1.00: SATA link down (SStatus 0 SControl 300)
[ 1.150651] ata1.01: SATA link down (SStatus 0 SControl 300)
[ 1.192353] usb 2-5: configuration #1 chosen from 1 choice
[ 1.310077] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.310090] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.350606] ata2.00: ATA-8: ST3500820AS, SD25, max UDMA/133
[ 1.350609] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.351007] ata2.01: ATA-8: ST3500320AS, SD1A, max UDMA/133
[ 1.351011] ata2.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.390617] ata2.00: configured for UDMA/133
[ 1.430579] ata2.01: configured for UDMA/133
[ 1.430716] scsi 1:0:0:0: Direct-Access ATA ST3500820AS SD25 PQ: 0 ANSI: 5
[ 1.430795] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 1.430802] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.430834] sd 1:0:0:0: [sda] Write Protect is off
[ 1.430835] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.430867] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.430914] scsi 1:0:1:0: Direct-Access ATA ST3500320AS SD1A PQ: 0 ANSI: 5
[ 1.430974] sd 1:0:1:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.430979] sd 1:0:1:0: Attached scsi generic sg1 type 0
[ 1.431007] sd 1:0:1:0: [sdb] Write Protect is off
[ 1.431008] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.431013] sda:
[ 1.431027] sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.459647] sda1 sda2 sda3
[ 1.459784] sdb:
[ 1.471275] usb 7-1: new full speed USB device using uhci_hcd and address 2
[ 1.472585] sdb1
[ 1.472778] sd 1:0:0:0: [sda] Attached SCSI disk
[ 1.472785] sd 1:0:1:0: [sdb] Attached SCSI disk
[ 1.472802] Freeing unused kernel memory: 888k freed
[ 1.473027] Write protecting the kernel read-only data: 7692k
[ 1.482147] udev: starting version 151
[ 1.530158] ahci 0000:03:00.0: version 3.0
[ 1.530936] pata_marvell 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.530960] pata_marvell 0000:03:00.0: setting latency timer to 64
[ 1.538222] Initializing USB Mass Storage driver...
[ 1.539827] ATL1E 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.539839] ATL1E 0000:02:00.0: setting latency timer to 64
[ 1.545433] scsi4 : pata_marvell
[ 1.549803] Floppy drive(s): fd0 is 1.44M
[ 1.553688] scsi6 : pata_marvell
[ 1.553723] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 16
[ 1.553725] ata6: PATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 16
[ 1.554589] ohci1394 0000:05:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.556644] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1.556746] usbcore: registered new interface driver usb-storage
[ 1.556748] USB Mass Storage support registered.
[ 1.556801] usb-storage: device found at 4
[ 1.556802] usb-storage: waiting for device to settle before scanning
[ 1.573779] FDC 0 is a post-1991 82077
[ 1.613356] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] MMIO=[febee000-febee7ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 1.641237] usb 7-1: configuration #1 chosen from 1 choice
[ 1.644209] hub 7-1:1.0: USB hub found
[ 1.646183] hub 7-1:1.0: 4 ports detected
[ 1.931286] usb 7-2: new full speed USB device using uhci_hcd and address 3
[ 2.173274] usb 7-2: configuration #1 chosen from 1 choice
[ 2.251185] usb 7-1.3: new low speed USB device using uhci_hcd and address 4
[ 2.280363] EXT4-fs (sda3): mounted filesystem with ordered data mode
[ 2.391262] usb 7-1.3: configuration #1 chosen from 1 choice
[ 2.471177] usb 7-1.4: new low speed USB device using uhci_hcd and address 5
[ 2.623252] usb 7-1.4: configuration #1 chosen from 1 choice
[ 2.940241] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c00015ce429]
[ 6.550216] usb-storage: device scan complete
[ 6.550952] scsi 5:0:0:0: Direct-Access WD Ext HDD 1021 2002 PQ: 0 ANSI: 4
[ 6.551356] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 6.551936] sd 5:0:0:0: [sdc] 2930272256 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 6.552809] sd 5:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 6.552812] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 6.554308] sd 5:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 6.554310] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 6.554313] sdc: sdc1
[ 6.563308] sd 5:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 6.563311] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 6.563313] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 12.534023] udev: starting version 151
[ 12.691872] [drm] Initialized drm 1.1.0 20060810
[ 12.708230] lp: driver loaded but no devices found
[ 12.718840] type=1505 audit(1322683765.722:2): operation="profile_load" pid=724 name="/sbin/dhclient3"
[ 12.719286] type=1505 audit(1322683765.722:3): operation="profile_load" pid=724 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.719567] type=1505 audit(1322683765.722:4): operation="profile_load" pid=724 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.720840] type=1505 audit(1322683765.732:5): operation="profile_replace" pid=748 name="/sbin/dhclient3"
[ 12.721286] type=1505 audit(1322683765.732:6): operation="profile_replace" pid=748 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.721532] type=1505 audit(1322683765.732:7): operation="profile_replace" pid=748 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.737520] [drm] radeon defaulting to kernel modesetting.
[ 12.737522] [drm] radeon kernel modesetting enabled.
[ 12.737571] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.737574] radeon 0000:01:00.0: setting latency timer to 64
[ 12.739162] [drm] radeon: Initializing kernel modesetting.
[ 12.748306] [drm] register mmio base: 0xFE8E0000
[ 12.748308] [drm] register mmio size: 65536
[ 12.748351] ATOM BIOS: Wekiva
[ 12.748363] [drm] Clocks initialized !
[ 12.748380] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[ 12.748381] [drm] Detected VRAM RAM=256M, BAR=256M
[ 12.748382] [drm] RAM width 256bits DDR
[ 12.749362] [TTM] Zone kernel: Available graphics memory: 2028824 kiB.
[ 12.749374] [drm] radeon: 256M of VRAM memory ready
[ 12.749376] [drm] radeon: 512M of GTT memory ready.
[ 12.749404] alloc irq_desc for 28 on node -1
[ 12.749406] alloc kstat_irqs on node -1
[ 12.749414] radeon 0000:01:00.0: irq 28 for MSI/MSI-X
[ 12.749418] radeon 0000:01:00.0: radeon: using MSI.
[ 12.749436] [drm] radeon: irq initialized.
[ 12.749438] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 12.749868] [drm] Loading RV770 Microcode
[ 12.749871] platform radeon_cp.0: firmware: requesting radeon/RV770_pfp.bin
[ 12.756499] platform radeon_cp.0: firmware: requesting radeon/RV770_me.bin
[ 12.761819] platform radeon_cp.0: firmware: requesting radeon/R700_rlc.bin
[ 12.769562] usbcore: registered new interface driver hiddev
[ 12.784343] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input3
[ 12.784401] generic-usb 0003:046D:C05A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.1-1.3/input0
[ 12.799349] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.4/7-1.4:1.0/input/input4
[ 12.799402] generic-usb 0003:0461:0010.0002: input,hidraw1: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:1d.1-1.4/input0
[ 12.822208] [drm] ring test succeeded in 1 usecs
[ 12.822284] [drm] radeon: ib pool ready.
[ 12.822344] [drm] ib test succeeded in 0 usecs
[ 12.822529] [drm] Default TV standard: NTSC
[ 12.822834] [drm] Radeon Display Connectors
[ 12.822836] [drm] Connector 0:
[ 12.822837] [drm] DVI-I
[ 12.822838] [drm] HPD1
[ 12.822839] [drm] DDC: 0x7e60 0x7e60 0x7e64 0x7e64 0x7e68 0x7e68 0x7e6c 0x7e6c
[ 12.822840] [drm] Encoders:
[ 12.822841] [drm] DFP1: INTERNAL_UNIPHY
[ 12.822842] [drm] CRT2: INTERNAL_KLDSCP_DAC2
[ 12.822843] [drm] Connector 1:
[ 12.822844] [drm] DIN
[ 12.822845] [drm] Encoders:
[ 12.822846] [drm] TV1: INTERNAL_KLDSCP_DAC2
[ 12.822847] [drm] Connector 2:
[ 12.822848] [drm] DVI-I
[ 12.822848] [drm] HPD2
[ 12.822850] [drm] DDC: 0x7e20 0x7e20 0x7e24 0x7e24 0x7e28 0x7e28 0x7e2c 0x7e2c
[ 12.822851] [drm] Encoders:
[ 12.822852] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 12.822853] [drm] DFP2: INTERNAL_KLDSCP_LVTMA
[ 12.835217] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.4/7-1.4:1.1/input/input5
[ 12.835274] generic-usb 0003:0461:0010.0003: input,hidraw2: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:1d.1-1.4/input1
[ 12.835293] usbcore: registered new interface driver usbhid
[ 12.835295] usbhid: v2.6:USB HID core driver
[ 12.838890] alloc irq_desc for 22 on node -1
[ 12.838892] alloc kstat_irqs on node -1
[ 12.838896] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 12.838931] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 12.875384] usbcore: registered new interface driver snd-usb-audio
[ 12.956577] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 12.976273] [drm] fb mappable at 0xD0142000
[ 12.976275] [drm] vram apper at 0xD0000000
[ 12.976276] [drm] size 8294400
[ 12.976277] [drm] fb depth is 24
[ 12.976278] [drm] pitch is 7680
[ 12.976326] fb0: radeondrmfb frame buffer device
[ 12.976327] registered panic notifier
[ 12.976331] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 12.976365] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 12.976391] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 12.978369] vga16fb: initializing
[ 12.978372] vga16fb: mapped to 0xffff8800000a0000
[ 12.978373] vga16fb: not registering due to another framebuffer present
[ 13.014997] Console: switching to colour frame buffer device 240x67
[ 13.106332] type=1505 audit(1322683766.112:8): operation="profile_load" pid=1095 name="/usr/share/gdm/guest-session/Xsession"
[ 13.106467] type=1505 audit(1322683766.112:9): operation="profile_replace" pid=1096 name="/sbin/dhclient3"
[ 13.106917] type=1505 audit(1322683766.112:10): operation="profile_replace" pid=1096 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 13.107164] type=1505 audit(1322683766.112:11): operation="profile_replace" pid=1096 name="/usr/lib/connman/scripts/dhclient-script"
[ 13.445631] alloc irq_desc for 29 on node -1
[ 13.445633] alloc kstat_irqs on node -1
[ 13.445644] ATL1E 0000:02:00.0: irq 29 for MSI/MSI-X
[ 13.445769] ATL1E 0000:02:00.0: ATL1E: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 13.446003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.446257] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.133640] Bridge firewalling registered
[ 14.141448] virbr0: starting userspace STP failed, starting kernel STP
[ 14.157219] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.179070] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.179214] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 14.179216] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 14.179217] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 14.645100] RPC: Registered udp transport module.
[ 14.645102] RPC: Registered tcp transport module.
[ 14.645103] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.662957] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 14.698021] svc: failed to register lockdv1 RPC service (errno 97).
[ 14.698561] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 14.698938] NFSD: starting 90-second grace period
[ 14.864031] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 14.864033] vboxdrv: Successfully done.
[ 14.864034] vboxdrv: Found 2 processor cores.
[ 14.864110] VBoxDrv: dbg - g_abExecMemory=ffffffffa04f4a20
[ 14.864122] vboxdrv: fAsync=0 offMin=0x143 offMax=0x6dd
[ 14.864312] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 14.864313] vboxdrv: Successfully loaded version 3.1.6_OSE (interface 0x00100001).
[ 15.036636] ppdev: user-space parallel port driver
[ 15.863385] CPU0 attaching NULL sched-domain.
[ 15.863388] CPU1 attaching NULL sched-domain.
[ 15.911372] CPU0 attaching sched-domain:
[ 15.911374] domain 0: span 0-1 level MC
[ 15.911376] groups: 0 1
[ 15.911380] CPU1 attaching sched-domain:
[ 15.911381] domain 0: span 0-1 level MC
[ 15.911383] groups: 1 0
[ 16.341547] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj.
[ 23.881262] eth0: no IPv6 routers present
[ 24.380024] virbr0: no IPv6 routers present
Danke für eure hilfe!
Basti