linux & linux dualboot

A

Andre

Foren Gott
HI
hab gerade ne 2te debian distribution installiert...
also in etwa so:
/dev/hda3 debian unstable
/devhda1 swap
/dev/hda2 debian stable

aber irgendwie krieg ich lilo nicht dazu beides ins bootmenue auf zu nehmen...
hat einer von euch sowas schon mal gemacht?
krieg immer den fehler not valid boot signature vom lilo?!?!
 
da gibts ja bisher nichts zu sehen...
hätte mir nen lilo.conf von jemand anderem gewünscht...der solch ein ding schon realisiert hat *fg*
###############################
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81

#disk=/dev/sda
# bios=0x80

# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda3

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
# prompt
# single-key
# delay=100
# timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append="pci=acpi" "hdc=ide-scsi"
append="hdc=ide-scsi"

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
label=Linux
read-only
# restricted
# alias=1

image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
other=/dev/hda1
label="Other(hda1)"

#other=/dev/hda2
#root=/dev/hda2
#label="WinNT(hda2)"
#table=/dev/hda
#image=/vmlinuz
###############################
 
habs schon gelöst...hab 2 lilo`s installiert..
einen auf /dev/hda3
den anderen in den MBR...das lief dann auf einmal ?!
 

Ähnliche Themen

Windows clients können nicht mehr auf lange laufendes System zugreifen

/dev/sdb1 has been mounted 22 times without being checked

Festplatten sind immer "busy", RAID1 Problem

linux oder doch vista?

Debian stable bleibt bei "io scheduler cfq registered (default)" haengen

Zurück
Oben