DMA macht was es will!

thei

thei

Foren As
Hi,

Hab seit neuesten macht der DMA Modus meiner 2. Festplatte was er will (Festplatte unterstützt DMA100) aber laut Yast läuft die Platte fast immer in DMA 44 modus, wenn ich Sie dann auf DMA 100 stelle und wieder nachgucke ist sie wieder auf DMA 44, was gibt´s da für ne möglichkeit das die Festplatte immer im DMA 100 modus ist?

Edit: Hab vergessen, handelt sich um Suse 10.2
 
Zuletzt bearbeitet:
poste bitte ein
Code:
dmesg
nach dem ändern auf dma100
 
Bitte schön:

Code:
Linux version 2.6.18.8-0.5-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Fri Jun 22 12:17:53 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
 BIOS-e820: 000000005fff0000 - 000000005fff8000 (ACPI data)
 BIOS-e820: 000000005fff8000 - 0000000060000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 393200
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 163824 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 AMI                                   ) @ 0x000fa970
ACPI: RSDT (v001 AMIINT VIA_K7   0x00000010 MSFT 0x00000097) @ 0x5fff0000
ACPI: FADT (v001 AMIINT VIA_K7   0x00000011 MSFT 0x00000097) @ 0x5fff0030
  >>> ERROR: Invalid checksum
ACPI: DSDT (v001    VIA   VT8371 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: Unable to map DSDT
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000)
Detected 1333.406 MHz processor.
Built 1 zonelists.  Total pages: 393200
Kernel command line: root=/dev/hda2 vga=0x317 resume=/dev/hda1 splash=silent
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01c0f000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1551884k/1572800k available (1697k kernel code, 19620k reserved, 1000k data, 196k init, 655296k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2669.59 BogoMIPS (lpj=5339199)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3153k freed
ACPI: Core revision 20060707
ACPI Warning (tbutils-0299): Incorrect checksum in table [FACP] - is 0E, should be 69 [20060707]
ACPI: setting ELCR to 0200 (from 1e00)
CPU0: AMD Athlon(tm) Processor stepping 04
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0c00-0c7f claimed by vt82c686 HW-mon
PCI quirk: region 0400-040f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: 7000-8fff
  MEM window: dfe00000-dfefffff
  PREFETCH window: bfc00000-dfcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1186496659.880:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:55a3
vesafb: pmi: set display start = c00c5637, set palette = c00c5683
vesafb: pmi: ports = 8810 8816 8854 8838 883c 885c 8800 8804 88b0 88b2 88b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 bytes,<6>...found (1024x768, 46202 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
 S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: Processor [CPU1] (supports 16 throttling states)
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD400BB-00DEA0, ATA DISK drive
hdb: MATSHITADVD-RAM SW-9574S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
 hda: hda1 hda2
Probing IDE interface ide1...
hdc: WDC WD800JB-00ETA0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 512KiB
hdc: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hdc: cache flushes supported
 hdc:hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide1: reset: success
 hdc1
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
JBD: barrier-based sync failed on hda2 - disabling barriers
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: VIA parallel port: io=0x378, irq=7
lp0: using parport0 (interrupt-driven).
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
hda: set_drive_speed_status: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
No module found in object
hda: CHECK for good STATUS
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 12, io base 0x0000cc00
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.8-0.5-default uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
shpchp: Unknown symbol acpi_run_oshp
shpchp: Unknown symbol pci_hp_change_slot_info
shpchp: Unknown symbol pci_hp_register
shpchp: Unknown symbol pci_hp_deregister
shpchp: Unknown symbol acpi_get_hp_params_from_firmware
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.2[C] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:0a.2: EHCI Host Controller
ehci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0a.2: irq 11, io mem 0xdffffe00
ehci_hcd 0000:00:0a.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.8-0.5-default ehci_hcd
usb usb2: SerialNumber: 0000:00:0a.2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:07.3: irq 12, io base 0x0000d000
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.8-0.5-default uhci_hcd
usb usb3: SerialNumber: 0000:00:07.3
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:0a.0: UHCI Host Controller
uhci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:0a.0: irq 10, io base 0x0000c000
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.18.8-0.5-default uhci_hcd
usb usb4: SerialNumber: 0000:00:0a.0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
hdb: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:0a.1: UHCI Host Controller
uhci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:0a.1: irq 12, io base 0x0000c400
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.18.8-0.5-default uhci_hcd
usb usb5: SerialNumber: 0000:00:0a.1
usb 1-2: new device found, idVendor=046d, idProduct=c506
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: USB Receiver
usb 1-2: Manufacturer: Logitech
usb 1-2: configuration #1 chosen from 1 choice
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:07.5 to 64
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 1414 MBytes.
[fglrx] USWC is disabled in module parameters
[fglrx] PAT is disabled!
[fglrx] module loaded - fglrx 8.39.4 [Jul 20 2007] on minor 0
JBD: barrier-based sync failed on hda2 - disabling barriers
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide1: reset: success
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xf904cf00, 00:0e:2e:37:47:bd, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
usb 4-1: new full speed USB device using uhci_hcd and address 2
usb 4-1: new device found, idVendor=1019, idProduct=0c55
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Product: USB Storage Device
usb 4-1: Manufacturer: Generic
usb 4-1: SerialNumber: 20020509145305401
usb 4-1: configuration #1 chosen from 1 choice
hdb: set_drive_speed_status: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: set_drive_speed_status: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
usb 4-2: new full speed USB device using uhci_hcd and address 3
SCSI subsystem initialized
Initializing USB Mass Storage driver...
hdb: CHECK for good STATUS
usb 4-2: new device found, idVendor=0a12, idProduct=0001
usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 4-2: configuration #1 chosen from 1 choice
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hiddev
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:07.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hci_usb
Adding 2104472k swap on /dev/hda1.  Priority:-1 extents:1 across:2104472k
  Vendor: IC        Model: USB Storage-CFC   Rev: 301b
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: IC        Model: USB Storage-SMC   Rev: 301b
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: IC        Model: USB Storage-MMC   Rev: 301b
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: IC        Model: USB Storage-MSC   Rev: 301b
  Type:   Direct-Access                      ANSI SCSI revision: 00
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
sd 0:0:0:1: Attached scsi removable disk sdb
sd 0:0:0:2: Attached scsi removable disk sdc
sd 0:0:0:3: Attached scsi removable disk sdd
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:1: Attached scsi generic sg1 type 0
sd 0:0:0:2: Attached scsi generic sg2 type 0
sd 0:0:0:3: Attached scsi generic sg3 type 0
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
JBD: barrier-based sync failed on hda2 - disabling barriers
loop: loaded (max 8 devices)
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1186496682.669:2): AppArmor initialized

ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
powernow-k8: Processor cpuid 644 not supported
powernow: No powernow capabilities detected
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
audit(1186489499.447:3): audit_pid=3348 old=0 by auid=4294967295
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[fglrx] Maximum main memory to use for locked dma buffers: 1414 MBytes.
[fglrx] AGP detected, AgpState   = 0x1f000217 (hardware caps of chipset)
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[fglrx] AGP enabled,  AgpCommand = 0x1f000314 (selected caps)
[fglrx] total      GART = 67108864
[fglrx] free       GART = 51113984
[fglrx] max single GART = 51113984
[fglrx] total      LFB  = 134217728
[fglrx] free       LFB  = 90165248
[fglrx] max single LFB  = 90165248
[fglrx] total      Inv  = 0
[fglrx] free       Inv  = 0
[fglrx] max single Inv  = 0
[fglrx] total      TIM  = 0
eth0: no IPv6 routers present
st: Version 20050830, fixed bufsize 32768, s/g segs 256
hdb: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdb: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdb: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdb: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdb: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide1: reset: success

Ide Konfiguration ist momentan bei mir so (alles mit 80 Poligen IDE Kabeln):

1. IDE Kanal Master: Festplatte (40 GIG Linux, /dev/hda2, /dev/hda1 ist die swap) läuft mit UDMA 100
1. IDE Kanal Slave: DVD-Brenner (/dev/hdb) läuft mit UDMA 66

2. IDE Kanal Master: 2. Festplatte (80 GIG für Daten, /dev/hdc1) macht probleme
2. IDE Kanal Slave: Nix
 
Zuletzt bearbeitet:
Diagnostikprogramm des Plattenherstellers besorgen und Platte durchtesten, dann weist du 100% Bescheid.

Wenn man sowas sieht:

Code:
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide1: reset: success
ist definitiv mit der Hardware was im Argen. Kaputtes Kabel oder sterbende Platte. S.o.
 
Hi,

Hab gerade beide IDE Kabel "erneuert" und siehe da soweit keine Probleme mehr! :) Mal gucken ob das Problem noch mal auftaucht...
 
Manchmal liegts auch am BIOS. Musst dir mal da die UDMA-Modi anschauen im Falle dessen das die Platte und die Verkabelung i.O. sind.
 

Ähnliche Themen

Alternative zu Ubuntu gesucht + Mängelliste

Hardware RAID-0 kaputt / wird nicht mehr erkannt

Laptop wird unter SuSe super heiß und stürzt regelm. ab

Umstieg auf Linux auf den PC's.

DMA von Festplatte kann nicht eingeschaltet werden

Zurück
Oben