Boot stoppt bei hda_intel: azx_get_response...

hengs

hengs

Tripel-As
Hallo Leute,

hab seit heute morgen das Problem, dass mein Rechner während des Bootvorganges stehen bleibt:

Code: 
hda_intel: azx_get_response timeout, switching to single_cmd mode...

Gestern abend hat noch alles funktioniert. In der Zwischenzeit wurde auch kein Update gemacht oder sonstige Programme installiert.

fsck hat keine Fehler gemeldet

Mein System:
Debian Lenny (dist-upgrade vom 16.07.2007)
Kernel 2.6.18-3-686

Mein Rechner:
Sony Vaio VGN-FS115M
Pentium M Prozessor 730, 1,60 GHz, 533 MHz FSB
nVidia Corporation GeForce Go 6200 TurboCache


hda:
FUJITSU MHT2080AT 80 GB Festplatte (Ultra-ATA-100 mit 4200 U/min)

Partitionen:
Code: 
/dev/hda5             6,5G  4,1G  2,1G  67% /
tmpfs                 252M     0  252M   0% /lib/init/rw
udev                   10M  104K  9,9M   2% /dev
tmpfs                 252M     0  252M   0% /dev/shm
/dev/hda7              25G   16G  7,8G  67% /home

Im vorderen Bereich der Festplatte befindet sich noch eine NTFS-Partition.

Ausgabe von dmesg:
Code: 
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
 BIOS-e820: 000000001fee0000 - 000000001feea000 (ACPI data)
 BIOS-e820: 000000001feea000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
On node 0 totalpages: 130784
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 126688 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f7530
ACPI: RSDT (v001   Sony       J0 0x20050225 PTL  0x00000000) @ 0x1fee5a12
ACPI: MADT (v001   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9e78
ACPI: FADT (v002   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9ee0
ACPI: BOOT (v001   Sony       J0 0x20050225 PTL  0x00000001) @ 0x1fee9fd8
ACPI: MCFG (v001   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9f9c
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee62cf
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5e8a
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5c6f
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5a56
ACPI: DSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1596.300 MHz processor.
Built 1 zonelists.  Total pages: 130784
Kernel command line: root=/dev/hda5 ro noapic nolapic vga=0x317 
mapped APIC to ffffd000 (0140a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510648k/523136k available (1543k kernel code, 11944k reserved, 574k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3195.77 BogoMIPS (lpj=6391549)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0cb8)
CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4769k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:06:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 90000000-afffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bus 7, cardbus bridge: 0000:06:03.0
  IO window: 00002400-000024ff
  IO window: 00002800-000028ff
  PREFETCH window: 30000000-31ffffff
  MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: b0000000-b00fffff
  PREFETCH window: 30000000-31ffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:06:03.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:06:03.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1184924370.924:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
vesafb: framebuffer at 0xc0000000, mapped to 0xe0880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d1b0
vesafb: pmi: set display start = c00cd1e6, set palette = c00cd250
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 5, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 3 (level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 3, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: AT Translated Set 2 keyboard as /class/input/input0
Time: acpi_pm clocksource has been installed.
ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 10, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0x80004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:06:03.2[C] -> Link [LNKC] -> GSI 3 (level, low) -> IRQ 3
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[3]  MMIO=[b0004000-b00047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:06:08.0[A] -> Link [LNKE] -> GSI 7 (level, low) -> IRQ 7
e100: eth0: e100_probe: addr 0xb0007000, irq 7, MAC addr 00:01:4A:19:93:19
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 3 (level, low) -> IRQ 3
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: FUJITSU MHT2080AT, ATA DISK drive
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
hdb: SONY DVD RW DW-D56A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0800460301d23361]
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
input: PC Speaker as /class/input/input2
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
intel_rng: FWH not detected
input: PS/2 Mouse as /class/input/input3
input: AlpsPS/2 ALPS GlidePoint as /class/input/input4
Yenta: CardBus bridge found at 0000:06:03.0 [104d:818f]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:03.0, mfunc 0x01001b22, devctl 0x64
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2kmq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
Yenta: ISA IRQ mask 0x0050, PCI irq 10
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0xb0000000 - 0xb00fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI Interrupt 0000:06:04.0[A] -> Link [LNKG] -> GSI 10 (level, low) -> IRQ 10
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
hda_intel: azx_get_response timeout, switching to single_cmd mode...
 
Ja, für mich liest sich das eher wie ein Problem mit dem Onboard-Sound Chip...

Hast du schon mal probiert die Treiber neu zu installieren?
 
Danke für die Hilfe, aber das Problem hat sich von selbst gelöst:

Nach meinem Ausscheiden aus dem Unternehmen wurde der Laptop wurde rewindowsiert.
 
Anmelden, um zu antworten.

Ähnliche Themen

Problem bei der installation einer Sun Netzwerkkarte
Problem bei der installation einer Sun Netzwerkkarte: Guten Morgen zusammen, beim installieren einer zusätzlichen Netzwerkkarte habe ich ein Problem. Die Karte wird nicht automatisch installiert. Es handelt...

X startet nichtmehr
X startet nichtmehr: Hallo, ich habe versucht CUDA und OPENCL mit meiner Graka zum laufen zu bekommen ... nun hängt er aber schon beim Booten bei "started Update UTMP about...

xrandr: cant open display
xrandr: cant open display: Moin ich hier ein Problem und keine Lösung parat :/ Und zwar kA ob es daran liegt darf ich das erste mal mit ner ATI Graka Erfahrungen sammeln. Das Gerät...

UDEV rules - How ?
UDEV rules - How ?: Hallo zusammen, ich bin schon ne ganze weil am googlen, finde aber nicht die Loesung daher mal mein Post. Ich habe gerade mit OpenSuse udev rename...

SD-Karte kaputt?
SD-Karte kaputt?: Hallo, meine SD-Karte spinnt und dmesg liefert Fehlermeldungen. Ist die SD-Karte kaputt, oder ist da was mit FAT falsch? Wie kann ich die SD-Karte...

Neueste Themen

Zurück
Oben