Langer Bootvorgang Laptop mit Netzversorgung

hengs

hengs

Tripel-As
Hallo,

ich besitze ein Sony Vaio VGN-FS115M mit einem Intel Centrino.

Auf dem Laptop ist ein Debian testing mit dem Kernel 2.6.18-3-686 installiert.

Alles funktioniert wunderbar (WLAN, ACPI, cpufreq, Displayhelligkeit).
Das einzige was mich stört ist der extem lange Bootvorgang wenn der Laptop am Netz hängt. Dieser dautert ca. 4x so lange wie ein Bootvorgang bei Akkubetrieb.

Besonders lange hängt er an folgenden Stellen:

Code:
ACPI: Getting cpuindex for acpiid 0x1
...
Waiting for /dev to be fully populated
...
cs: IO port probe 0xa00-0xaff: clean.

Hier noch dmesg falls es jemanden was hilft:

Code:
Linux version 2.6.18-3-686 (Debian 2.6.18-7) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP Mon Dec 4 16:41:14 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
 BIOS-e820: 000000001fee0000 - 000000001feea000 (ACPI data)
 BIOS-e820: 000000001feea000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
On node 0 totalpages: 130784
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 126688 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f7530
ACPI: RSDT (v001   Sony       J0 0x20050225 PTL  0x00000000) @ 0x1fee5a12
ACPI: MADT (v001   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9e78
ACPI: FADT (v002   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9ee0
ACPI: BOOT (v001   Sony       J0 0x20050225 PTL  0x00000001) @ 0x1fee9fd8
ACPI: MCFG (v001   Sony       J0 0x20050225 PTL  0x0000005f) @ 0x1fee9f9c
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee62cf
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5e8a
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5c6f
ACPI: SSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x1fee5a56
ACPI: DSDT (v001   Sony       J0 0x20050225 PTL  0x20030224) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1596.300 MHz processor.
Built 1 zonelists.  Total pages: 130784
Kernel command line: root=/dev/hda5 ro vga=0x317 quiet splash  
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510648k/523136k available (1543k kernel code, 11940k reserved, 574k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3195.78 BogoMIPS (lpj=6391561)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
Total of 1 processors activated (3195.78 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4768k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:06:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 90000000-afffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bus 7, cardbus bridge: 0000:06:03.0
  IO window: 00002400-000024ff
  IO window: 00002800-000028ff
  PREFETCH window: 30000000-31ffffff
  MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: b0000000-b00fffff
  PREFETCH window: 30000000-31ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:06:03.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 169
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1166286653.964:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
vesafb: framebuffer at 0xc0000000, mapped to 0xe0880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d1b0
vesafb: pmi: set display start = c00cd1e6, set palette = c00cd250
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (54 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 193, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 201, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 209, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Time: acpi_pm clocksource has been installed.
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:06:03.2[C] -> GSI 18 (level, low) -> IRQ 209
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[209]  MMIO=[b0004000-b00047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 193, io mem 0x80004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:06:08.0[A] -> GSI 20 (level, low) -> IRQ 217
e100: eth0: e100_probe: addr 0xb0007000, irq 217, MAC addr 00:01:4A:19:93:19
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 209
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: FUJITSU MHT2080AT, ATA DISK drive
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0800460301d23361]
hdb: SONY DVD RW DW-D56A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Yenta: CardBus bridge found at 0000:06:03.0 [104d:818f]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:03.0, mfunc 0x01001b22, devctl 0x64
input: PS/2 Mouse as /class/input/input2
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Yenta: ISA IRQ mask 0x0cf8, PCI irq 169
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0xb0000000 - 0xb00fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 201
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2kmq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 22 (level, low) -> IRQ 225
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ts: Compaq touchscreen protocol output
ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.
psmouse.c: resync failed, issuing reconnect request
Adding 1164672k swap on /dev/hda6.  Priority:-1 extents:1 across:1164672k
EXT3 FS on hda5, internal journal
loop: loaded (max 8 devices)
SCSI subsystem initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ACPI Sony Notebook Control Driver v0.2-PP successfully installed
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Power Button (CM) [PWRB]
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input4
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
sonypi: Sony Programmable I/O Controller Driver v1.26.
sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on
sonypi: enabled at irq=11, port1=0x1080, port2=0x1084
sonypi: device allocated minor is 62
input: Sony Vaio Jogdial as /class/input/input5
input: Sony Vaio Keys as /class/input/input6
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-9629  Wed Nov  1 19:30:07 PST 2006
ieee80211_crypt: registered algorithm 'WEP'
ADDRCONF(NETDEV_UP): eth2: link is not ready
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
eth2: no IPv6 routers present
 
Hi,
Was für einen Bootloader verwendest du?
Falls du LiLo verwendest wechsel auf GRUB hatte das Problem auch und nachdem ich GRUB drauf hatte ging der Bootvorgang wieder so schnell wie immer.

MfG,

Buchi
 
Hmm ... einen "Fehler" seh ich nicht wirklich.
Vergleich doch mal die Ausgaben von dmesg beim Booten mit und ohne Netzteil ...
 
Bist du dir da sicher ? Beide mal abgespeichert und mal mit Diff verglichen ?
 
Bist du dir da sicher ? Beide mal abgespeichert und mal mit Diff verglichen ?

Sind gleich, außer natürlich

Code:
< ACPI: AC Adapter [ADP1] (off-line)
---
> ACPI: AC Adapter [ADP1] (on-line)

und

< Detected 1596.279 MHz processor.
---
> Detected 1596.177 MHz processor
 
Heißt das, dass dein Notebook ohne Netzversorgung soger minimal schneller ist?

MfG,
Buchi
 
Eine Lösung für das Problem habe ich zwar auch nicht, aber mir ist heute bei einem
Kollegen (MSI-Notebook/Centrino) aufgefallen das der Bootvorgang (Netzbetrieb)
ebenfalls sehr lange gedauert hat.
An dem Notebook sind LED-Kontrollleuchten für W-LAN & Bluetooth.
Im Netzbetrieb schalten diese (wärend des Bootvorgangs) von rot (deaktiviert) auf
grün (aktiviert).
Im Batteriebetrieb bleiben diese rot bis er eine Verbindung aufbauen will, erst dann
werden diese aktiviert.
Möglicherweise ist das eine Erklärung für die lange Bootzeit.
 
Eine Lösung für das Problem habe ich zwar auch nicht, aber mir ist heute bei einem
Kollegen (MSI-Notebook/Centrino) aufgefallen das der Bootvorgang (Netzbetrieb)
ebenfalls sehr lange gedauert hat.
An dem Notebook sind LED-Kontrollleuchten für W-LAN & Bluetooth.
Im Netzbetrieb schalten diese (wärend des Bootvorgangs) von rot (deaktiviert) auf
grün (aktiviert).
Im Batteriebetrieb bleiben diese rot bis er eine Verbindung aufbauen will, erst dann
werden diese aktiviert.
Möglicherweise ist das eine Erklärung für die lange Bootzeit.

Ändert leider auch nichts!

mfg
 
Hi,
Verbindest du dich zu einem W-Lan Netzwerk oder gehst du direkt in Internet? Denn wenn du dich wirklich mit einem W-Lan Netzwerk verbindest könntest du probieren dich erst zu verbinden, wenn der Laptop hochgefahren ist.

MfG,
Buchi
 
Hallo,

ich verbinde mich mit einem WLan, aber eh erst wenn das System hochgefahren ist und nicht automatisch.
 
Hallo!

Habe dieses Problem ebenfalls und bin beim Googeln auf diesen Beitrag aufmerksam geworden.

Bei meinem VGN FS115 ist es so das es im Akkubetrieb schnell bootet und alles einwandfrei funktioniert. Stecke ich jedoch den Netzadapter an wird das System sofort total langsam, teilweise ruckelt die Grafikausgabe etc.

Alle Versuche das ganze über die Performance-Profile in den Griff zu bekommen führte nur zu minimalen Verbesserungen. Richtig schnell ist es immer nur dann wenn der Netzstecker ab ist.

Dieses Problem konnte ich nun unter Suse, Kubuntu und Mandriva beobachten.
Offensichtlich funktioniert Cpufreq bei dem Laptop nicht korrekt.

Hat jemand Tipps was man da tun kann?

Grüße
matzzze
 
Zuletzt bearbeitet:
also ich hab ein Toshiba Laptop (siehe signatur) und ich hab keinerlei probleme, ich denke aber das liegt an euerer "kastrierten" CPU, ich habe hier einen "echten" P4 und mit dem geht das ganze perfekt, sogar die temperatur ist besser als win xp.
 
wie waers mal mit noacpi zu booten, weil er haengt doch bei was acpi, oder?
 
Nee, das bringt nix. Habe testweise alles was mit ACPI & CPUFreq. zu tun hat deaktiviert. Das seltsame Akku/Netzeil-Verhalten bleibt :(

Ergänzung:
Nach endlos langer Suche im Web habe ich einen ähnlichen Thread gefunden. Beim Centrino soll man den Kernel mit den Optionen nolapic noapic booten dann wäre das Problem gelöst, ich probiere das morgen abend mal aus und berichte dann.

Ergänzung 2:
Das Booten mit nolapic noapic hat das Problem tatsächlich behoben :-)
 
Zuletzt bearbeitet:
Das Booten mit nolapic noapic hat das Problem tatsächlich behoben :-)

Hat tatsächlich geholfen,

aber welche Folgen hat nolapic bzw noapic für mein Centrino-System

Im Netz teilen sich die Meinungen:
*Single CPUs sind nicht betroffen, nur auf SMP Maschinen sind Leistungseinschränkungen zu erwarten
* Andere behaupten, dass es Probleme bei der Interrupt-Aufteilung geben kann

Weiß von euch jemand mehr?
 

Ähnliche Themen

X startet nichtmehr

xrandr: cant open display

UDEV rules - How ?

Modulfehler?

Festplatte friert ein nach suspend/resume

Zurück
Oben