Archiv verlassen und diese Seite im Standarddesign anzeigen : kann die grafische Oberfläche nicht starten (Debian)
hallo leute ich brauche dringend hilfe ich habe voip auf meinem rechner installiert aber ich kenne den befehl um in die grafiche oberfläche zu kommen nicht könnt ihr helfen? das system basiert auf debian gnu/linux!
wenn ihr den befehl dafür kennt würde ich mich sehr freuen:D
schonmal ein danke im vorraus
Hi,
also ein paar mehr Informationen über dein System (du hast VoiP installiert? Die Installation wurde grade abgeschlossen? Hast du zusätzliche Programme installiert? Hast du Linux Erfahrung?) oder ein passender Betreff wären sehr hilfreich.
Die grafische Oberfläche startest du normalerweise mit dem Befehl "startx" aber da ich mal annehme, dass du gar keine Oberfläche installiert hast solltest du erstmal die Pakete
Xfree86 (oder X.org, hängt von deinem Debian ab)
sowie eine Desktopoberfläche (KDE oder Gnome) installieren.
Wie bist du eigentlich auf Debian gekommen wenn ich mal so fragen darf
supersucker
22.06.2006, 09:43
startx
"Hilfe!!!" ist übrigens ein wahnsinnig aussagekräftiger Titel.
Hi,
also ein paar mehr Informationen über dein System (du hast VoiP installiert? Die Installation wurde grade abgeschlossen? Hast du zusätzliche Programme installiert? Hast du Linux Erfahrung?) oder ein passender Betreff wären sehr hilfreich.
Die grafische Oberfläche startest du normalerweise mit dem Befehl "startx" aber da ich mal annehme, dass du gar keine Oberfläche installiert hast solltest du erstmal die Pakete
Xfree86 (oder X.org, hängt von deinem Debian ab)
sowie eine Desktopoberfläche (KDE oder Gnome) installieren.
Wie bist du eigentlich auf Debian gekommen wenn ich mal so fragen darf
ich bin in der computer firma wo ich helfe die haben voip installiert jetzt haben sie mich gefragt ob ich helfen kann so aber damit habe ich selber probleme, der comp sagt ja das xfree86 installiert wäre aber es startet nicht? ich selber bin programmierer und bin dabei cynux zu programmieren!
ich habe alles ausprobiert aber da geht nichts! ich fang gleich an zu weinen
Na und was sagt "startx" ?
supersucker
22.06.2006, 09:59
Ist das nun ein Troll oder ein Fake oder beides?
Ist das nun ein Troll oder ein Fake oder beides?
garnichts von beiden!
startx funst nicht
startx funst nicht
Eine Fehlerbeschreibung die rockt. Was gibt der Befehl den nun aus?
Edward Nigma
22.06.2006, 10:18
Ich denke, daß da überhaupt keine grafische Oberfläche installiert ist!
Naja im zweiten Posting sagt er ja, dass zumindest Xfree86 installiert ist.
Wär vielleicht auch gut zu wissen ob er bei der Installation (ich nehme jetzt einfach mal an, dass Sarge drauf ist) ein Minimalsystem ausgewählt hat oder gleich eine grafische Oberfläche
und was ist nun cynux? *g*
Edward Nigma
22.06.2006, 11:09
Naja im zweiten Posting sagt er ja, dass zumindest Xfree86 installiert ist.
Wär vielleicht auch gut zu wissen ob er bei der Installation (ich nehme jetzt einfach mal an, dass Sarge drauf ist) ein Minimalsystem ausgewählt hat oder gleich eine grafische Oberfläche
Ich frage mich halt warum der Befehl "startx" nicht funktioniert? Selbst wenn X nicht konfiguriert ist, würde eine Fehlermeldung erscheinen.
Naja, da die Infos von cynus eh sehr dünn sind, werden wir hier eh so schnell keine Lösung finden.
Ich frage mich was X mit VoIP zu tun hat und was ist eigentlich "cynux"?
naja, wenn cynux sich entschliesst, zu beschreiben was passiert, wenn er startx eingibt, dann dürfte das problem schnell zu lösen sein..
Naja, macht einen neuen Tread auf (http://www.unixboard.de/vb3/showthread.php?p=158960#post158960), antwortet hier aber nicht und geizt total mit Fehlermeldungen, als seien die streng geheim. Da sollte sich vielleicht jemand erstmal das Wissen ueber den Umgang mit einem Support-Forums und ein paar Linux-Grundkenntnisse aneignen. *find*
Naja, macht einen neuen Tread auf (http://www.unixboard.de/vb3/showthread.php?p=158960#post158960), antwortet hier aber nicht und geizt total mit Fehlermeldungen, als seien die streng geheim. Da sollte sich vielleicht jemand erstmal das Wissen ueber den Umgang mit einem Support-Forums und ein paar Linux-Grundkenntnisse aneignen. *find*
hmm der link geht bei mir ins leere, und scheinbar hat cynux auch wirklich nur 4 Antworten verfasst ?(
Den hat wohl ein Mod schon wieder geloescht, denn auch der RSS-Link dahin geht jetzt ins Leere. (siehe im RSS-Feed "Debian Problem"). Den sollte dann der Mod auch noch loeschen. :)
Den hat wohl ein Mod schon wieder geloescht, denn auch der RSS-Link dahin geht jetzt ins Leere. (siehe im RSS-Feed "Debian Problem"). Den sollte dann der Mod auch noch loeschen. :)
Jup ... MTS wars. Habs komplett gelöscht .. sollte somit auch nimmer im RSS auftauchen ;)
guten tag @alle leider habe ich auch n kleines problehm mit der grafischer oberfläche des linux debian :-( habe gestern das debian mit der cd neuinstaliert und dabei grafische oberfläche gewählt .... dann beim starten kam so n fehler das etwas nicht gut sei mit der grafischen oberfläche jetz habe ich das startx gemacht daraus kam dan dieser text
thomsti:~# startx
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
X: warning; process set to priority -1 instead of requested priority 0
XFree86 Version 4.3.0.1 (Debian 4.3.0.dfsg.1-14sarge1 20050901212727 fjp@localhost.localdomain)
Release Date: 15 August 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.6.8-16.0508-2 i686 [ELF]
Build Date: 02 September 2005
This version of XFree86 has been extensively modified by the Debian
Project, and is not supported by the XFree86 Project, Inc., in any
way. Bugs should be reported to the Debian Bug Tracking System; see
<URL: http://www.debian.org/Bugs/Reporting >.
We strongly encourage the use of the "reportbug" package and command
to ensure that bug reports contain as much useful information as
possible.
Before filing a bug report, you may want to consult the Debian X FAQ:
XHTML version: file:///usr/share/doc/xfree86-common/FAQ.xhtml
plain text version: file:///usr/share/doc/xfree86-common/FAQ.gz
Module Loader present
OS Kernel: Linux version 2.6.8-3-386 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Sat Jul 15 09:26:40 UTC 2006
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Sun Sep 10 11:50:22 2006
(==) Using config file: "/etc/X11/XF86Config-4"
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_clip.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_norm.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_xform.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_vertex.o": No symbols found
Skipping "/usr/X11R6/lib/modules/fonts/libspeedo.a:spencode.o": No symbols found
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Fatal server error:
Caught signal 11. Server aborting
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
XIO: fatal IO error 104 (Connection reset by peer) on X server ":0.0"
after 0 requests (0 known processed) with 0 events remaining.
kann mir einer helfen ?
mit freundlichen grüssen
thomsti
Sind die Module den installiert?
Hast du /etc/X11/XF86Config-4 editiert?
Schau mal in der Log-Datei nach, ob dort noch mehr steht. Am Besten mit
grep -n EE /var/log/XFree86.0.log dann bekommst du nur die Fehlermeldungen. Ich tippe mal darauf, dass X einfach falsch konfiguriert ist und ein falscher Treiber benutzt wird. Welche Grafikkarte hast du und welchen Treiber verwendest du dafuer?
thema dieser log datei befehl = [QUOTE] server:/# grep -n EE /var/log/XFree86.0.log
24: (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
223:(II) Loading extension MIT-SCREEN-SAVER
364:(EE) No devices detected.
[/QUOTE und es ist alles in etwa so wie es von dem progi instaliert wurde :-D
No devices detected.
Das sagt doch schon alles. Offenbar verwendest du den falschen Treiber.
ämmm da ist aber noch n grösseres problehm :s welches ist der richtige TREIBER ??? :S
Kommt auf die Karte an, die du drin hast.
sh.... leider hab ich keine ahnung was für ne karte das ist :s
gibt es ihrgend einen befehl um diese infos zu erhalten ?
Du kannst dir hwinfo installieren und damit nachschauen z.B.
und wie bitte lautet der befehl um dan anchzuchauen ich habe jetz apt-get install hwinfo gemacht und es hat instaliert :-D
und wie bitte lautet der befehl um dan anchzuchauen ich habe jetz apt-get install hwinfo gemacht und es hat instaliert :-D
So schwer isses doch nicht!
Alles in der Shell:
man hwinfo
bzw.
hwinfo
daraufhin gibt er dir die benötigten Infos.
P.S
Ich empfehle dir dringend ein Buch über Linux zu lesen oder dich im Internet nach geeigneten Tutorials umzuschauen, davon gibt es nämlich Unzählige!
Zum Beispiel
klick mich (http://www.selflinux.de)
oder
klick mich (http://www.linuxfibel.de)
Solche Fragen würde sich dann nämlich erübrigen und ganz nebenbei lernst du auch dein System kennen.
Gruß
Philipp
aus dem befehl hwinfo kommt folgenden und leider weis cih jetz nicht wo die grafischen sachen sind :S
I/O Ports: 0x3f8-0x3ff (rw)
IRQ: 4 (22 events)
Config Status: cfg=new, avail=yes, need=no, active=unknown
41: None 00.1: 0700 Serial controller (16550)
[Created at serial.73]
Unique ID: v9l_.3fyvFV+mbWD
Hardware Class: unknown
Model: "16550A"
Device: "16550A"
Device File: /dev/ttyS1
I/O Ports: 0x2f8-0x2ff (rw)
IRQ: 3 (20 events)
Config Status: cfg=new, avail=yes, need=no, active=unknown
42: IDE 00.0: 10600 Disk
[Created at block.190]
Unique ID: Fffu.pqWtGpmjKy8
Parent ID: +6Nb.L6YUholkGT8
SysFS ID: /block/hda
SysFS BusID: 0.0
SysFS Device Link: /devices/pci0000:00/0000:00:04.1/ide0/0.0
Hardware Class: disk
Model: "ST360020A"
Device: "ST360020A"
Revision: "3.39"
Serial ID: "5EX0XR6G"
Driver: "PIIX IDE", "ide-disk"
Device File: /dev/hda
Device Number: block 3:0-3:63
Geometry (Physical): CHS 16383/16/63
Geometry (Logical): CHS 65535/16/63
Size: 117231408 sectors a 512 bytes
Cache: 2048 kb
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #18 (IDE interface)
43: None 00.0: 11300 Partition
[Created at block.352]
Unique ID: 0fbI.SE1wIdpsiiC
Parent ID: Fffu.pqWtGpmjKy8
SysFS ID: /block/hda/hda1
Hardware Class: partition
Model: "Partition"
Device File: /dev/hda1
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #42 (Disk)
44: None 00.0: 11300 Partition
[Created at block.352]
Unique ID: TqrM.SE1wIdpsiiC
Parent ID: Fffu.pqWtGpmjKy8
SysFS ID: /block/hda/hda2
Hardware Class: partition
Model: "Partition"
Device File: /dev/hda2
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #42 (Disk)
45: None 00.0: 11300 Partition
[Created at block.352]
Unique ID: rMcZ.SE1wIdpsiiC
Parent ID: Fffu.pqWtGpmjKy8
SysFS ID: /block/hda/hda5
Hardware Class: partition
Model: "Partition"
Device File: /dev/hda5
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #42 (Disk)
46: SCSI 00.0: 10600 Disk
[Created at block.190]
Unique ID: _q_W.75FnPymdzGC
Parent ID: H0_h.FTvRPGtg70B
SysFS ID: /block/sda
SysFS BusID: 0:0:0:0
SysFS Device Link: /devices/pci0000:00/0000:00:06.0/host0/0:0:0:0
Hardware Class: disk
Model: "SEAGATE ST39173W"
Vendor: "SEAGATE"
Device: "ST39173W"
Revision: "5958"
Serial ID: "LM78278300007907HCGT"
Driver: "aic7xxx", "sd"
Device File: /dev/sda (/dev/sg0)
Device Number: block 8:0-8:15 (char 21:0)
Geometry (Logical): CHS 1106/255/63
Size: 17783240 sectors a 512 bytes
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #21 (SCSI storage controller)
47: None 00.0: 11300 Partition
[Created at block.352]
Unique ID: 1tKY.SE1wIdpsiiC
Parent ID: _q_W.75FnPymdzGC
SysFS ID: /block/sda/sda1
Hardware Class: partition
Model: "Partition"
Device File: /dev/sda1
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #46 (Disk)
48: SCSI 06.0: 10602 CD-ROM
[Created at block.194]
Unique ID: twPO.BDTABhT8kl1
Parent ID: H0_h.FTvRPGtg70B
SysFS ID: /block/sr0
SysFS BusID: 0:0:6:0
SysFS Device Link: /devices/pci0000:00/0000:00:06.0/host0/0:0:6:0
Hardware Class: cdrom
Model: "MATSHITA CD-ROM CR-506"
Vendor: "MATSHITA"
Device: "CD-ROM CR-506"
Revision: "8S05"
Driver: "aic7xxx", "sr"
Device File: /dev/sr0 (/dev/sg1)
Device Number: block 11:0 (char 21:1)
Drive status: no medium
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #21 (SCSI storage controller)
Drive Speed: 1
49: USB 00.0: 10a00 Hub
[Created at usb.120]
Unique ID: k4bc.6_yvaX5oIY7
Parent ID: sRsQ.3F5+CgnFyt9
SysFS ID: /devices/pci0000:00/0000:00:04.2/usb1/1-0:1.0
SysFS BusID: 1-0:1.0
Hardware Class: hub
Model: "Linux 2.6.8-3-386 uhci_hcd Intel Corp. 82371AB/EB/MB PIIX4 USB"
Hotplug: USB
Vendor: "Linux 2.6.8-3-386 uhci_hcd"
Device: "Intel Corp. 82371AB/EB/MB PIIX4 USB"
Revision: "2.06"
Serial ID: "0000:00:04.2"
Driver: "hub"
Speed: 1.5 Mbps
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #19 (USB Controller)
50: USB 00.0: 10900 Printer
[Created at usb.120]
Unique ID: cLrx.tPFeIE4e5t6
Parent ID: k4bc.6_yvaX5oIY7
SysFS ID: /devices/pci0000:00/0000:00:04.2/usb1/1-2/1-2:1.0
SysFS BusID: 1-2:1.0
Hardware Class: printer
Model: "HP LaserJet 1018"
Hotplug: USB
Vendor: usb 0x03f0 "HP"
Device: usb 0x4117 "HP LaserJet 1018"
SubVendor: "Hewlett-Packard"
SubDevice: "HP LaserJet 1018"
Revision: "1.00"
Serial ID: "KP04YM7"
Driver: "usblp"
Device File: /dev/usb/lp0
Device Number: char 180:0
Speed: 1.5 Mbps
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #49 (Hub)
51: PS/2 00.0: 10800 Keyboard
[Created at input.120]
Unique ID: nLyy.TBWTwSuMeW2
Hardware Class: keyboard
Model: "AT Translated Set 2 keyboard"
Vendor: int 0x0211
Device: int 0x0001 "AT Translated Set 2 keyboard"
Device File: /dev/input/event0
Device Number: char 13:64
Driver Info #0:
XkbRules: xfree86
XkbModel: pc104
Config Status: cfg=new, avail=yes, need=no, active=unknown
52: PS/2 00.0: 10500 PS/2 Mouse
[Created at input.140]
Unique ID: AH6Q.hI1e_vHaTSC
Hardware Class: mouse
Model: "ImPS/2 Logitech Wheel Mouse"
Vendor: int 0x0210
Device: int 0x0013 "ImPS/2 Logitech Wheel Mouse"
Device File: /dev/input/mice (/dev/input/mouse0)
Device Number: char 13:63 (char 13:32)
Driver Info #0:
Buttons: 3
Wheels: 1
XFree86 Protocol: explorerps/2
GPM Protocol: exps2
Config Status: cfg=new, avail=yes, need=no, active=unknown
53: None 00.0: 10701 Ethernet
[Created at net.88]
Unique ID: usDW.ndpeucax6V1
Parent ID: WL76.I82OYr9Rpy5
SysFS ID: /class/net/eth0
SysFS Device Link: /devices/pci0000:00/0000:00:09.0
Hardware Class: network interface
Model: "Ethernet network interface"
Driver: "e100"
Device File: eth0
HW Address: 00:08:c7:a9:e7:fc
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #22 (Ethernet controller)
54: None 00.0: 10700 Loopback
[Created at net.88]
Unique ID: ZsBS.GQNx7L4uPNA
SysFS ID: /class/net/lo
Hardware Class: network interface
Model: "Loopback network interface"
Device File: lo
Config Status: cfg=new, avail=yes, need=no, active=unknown
55: None 00.0: 10781 Network Interface
[Created at net.88]
Unique ID: wl2P.nfEXJulusj6
SysFS ID: /class/net/sit0
Hardware Class: network interface
Model: "Network Interface"
Device File: sit0
Config Status: cfg=new, avail=yes, need=no, active=unknown
thomsti:/opt/lampp/bin#
Goodspeed
15.09.2006, 17:58
Was ergibt denn
lspci
(eventuell muss Du das auch erst per apt installieren. Das Paket heißt dann pciutils)
Wolfgang
15.09.2006, 18:28
sh.... leider hab ich keine ahnung was für ne karte das ist :s
gibt es ihrgend einen befehl um diese infos zu erhalten ?
Das hier könnte dir auch etwas bringen. Alter Trick mit minimalen Boardmitteln.
dd if=/dev/mem bs=1k skip=768 count=1|strings -n 8
Zeigt auf einem handelsüblichen PC die vom BIOS erkannte Grafikkarte an.
;)
Wenn du mit dem skip und count etwas spielst, kommen noch andere Infos zu Tage.
Gruß Wolfgang
@wolfgang das ergibt bei mir folgendes
thomsti:~# dd if=/dev/mem bs=1k skip=768 count=1|strings -n 8
1+0 Datensätze ein
1+0 Datensätze aus
1024 bytes transferred in 0.000785 seconds (1304317 bytes/sec)
761295520
2000/03/27 14:21
Rage128 PRO GL P/N 113-65707-100
(C) 1988-99, ATI Technologies Inc. BK3.0.1 VR001.001.003.001.002.026 pfukk1x.301 v611
R128AGP SGS1UN
Goodspeed
16.09.2006, 07:06
ATI Rage128 Pro ... da sollte der "ati"-Treiber von XFree/Xorg reichen ...
Hast Du den X-Server schon richtig konfiguriert (xf86config/xf86cfg sollten da helfen) ...
ämmmm finde diese datei nicht :s gibt doch so n befehl oder ?
hab den befehl gefunden :D
ämm da ist noch die frage wie kann mann ales neustarten ? ohne pc restart
ich hab jetz mal startx gemchat da kam was von nem eror und ein dateifpad einer log datei diese hab ich angesehen und den schluss dieser datei poste ich jetz :-D
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "rage fury"
(WW) Warning, couldn't open module rage fury
(II) UnloadModule: "rage fury"
(EE) Failed to load module "rage fury" (module does not exist, 0)
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.4
(EE) No drivers available.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
hoffe auf schnelle antwort ;-)
Ich tippe mal darauf, dass du einen falschen Treiber eingestellt hast. ;)
Failed to load module "rage fury" (module does not exist, 0)
Nimm mal fbdev (vorausgesetzt du benutzt den Kernel-Framebuffer - Kernel-Paramter vga=0x317 fuer eine Aufloesung von 1024x768x16), den habe ich immer mit rage128GraKas genutzt.
hmmm immernoch das selbe prob oderc mach ich was falsch ? reconfigurieren mit dpkg-reconfigure xserver-xfree86
und neustarten mit startx ???
Sollte eigentlich korrekt sein, wenn du fbdev als Treiber nutzt und den Kernel-Framebuffer aktiviert hast.
wie weis ich ob kernel framebuffer aktiviert habe ?
Wenn deine Konsole eine Aufloesung hat, die nicht 640x480x256 ist.
wenn du fbdev als Treiber nutzt welcher treiber ist den das ?
Framebuffer-Device. Der steht als fbdev in der Liste der verfuegbaren X-Server-Treiber. http://www.bitmuncher.de/files/snapshot43.png
ok leider immernoch der fehler kein rage fury :-(
Dann schau doch einfach mal mit einem Editor in deine /etc/X11/XF86Config-4 wo dieses seltsame Modul eingetragen ist.
es steht
Section "Device"
Identifier "32"
Driver "rage fury"
BusID "1"
VideoRam 32
Option "UseFBDev" "true"
EndSection
ist da was falsch ?
Trage mal anstelle von rage fury einfach fbdev als Treiber ein
Driver "fbdev"
Nachtrag: Und nimm das UseFBDev raus (also einfach ein # an den Anfang der Zeile.
hmm gemacht und startx geschrieben und jetz kommt
thomsti:~# startx
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
X: warning; process set to priority -1 instead of requested priority 0
XFree86 Version 4.3.0.1 (Debian 4.3.0.dfsg.1-14sarge1 20050901212727 fjp@localhost.localdomain)
Release Date: 15 August 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.6.8-16.0508-2 i686 [ELF]
Build Date: 02 September 2005
This version of XFree86 has been extensively modified by the Debian
Project, and is not supported by the XFree86 Project, Inc., in any
way. Bugs should be reported to the Debian Bug Tracking System; see
<URL: http://www.debian.org/Bugs/Reporting >.
We strongly encourage the use of the "reportbug" package and command
to ensure that bug reports contain as much useful information as
possible.
Before filing a bug report, you may want to consult the Debian X FAQ:
XHTML version: file:///usr/share/doc/xfree86-common/FAQ.xhtml
plain text version: file:///usr/share/doc/xfree86-common/FAQ.gz
Module Loader present
OS Kernel: Linux version 2.6.8-3-386 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Sat Jul 15 09:26:40 UTC 2006
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Oct 4 22:34:33 2006
(==) Using config file: "/etc/X11/XF86Config-4"
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_clip.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_norm.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_xform.o": No symbols found
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_vertex.o": No symbols found
Skipping "/usr/X11R6/lib/modules/fonts/libspeedo.a:spencode.o": No symbols found
(EE) FBDEV(0): EGA/VGA planes are not yet supported by the fbdev driver [1]
free(): invalid pointer 0x86165e4!
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
XIO: fatal IO error 104 (Connection reset by peer) on X server ":0.0"
after 0 requests (0 known processed) with 0 events remaining.
thomsti:~#
Hast du noch irgendwelche gli-, glx- oder dri-, drm-Module in der Konfiguration stehen?
mache wirs einfach :-D die komplette config :-D
# XF86Config-4 (XFree86 X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the XF86Config-4 manual page.
# (Type "man XF86Config-4" at the shell prompt.)
#
# This file is automatically updated on xserver-xfree86 package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xfree86
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following commands as root:
#
# cp /etc/X11/XF86Config-4 /etc/X11/XF86Config-4.custom
# md5sum /etc/X11/XF86Config-4 >/var/lib/xfree86/XF86Config-4.md5sum
# dpkg-reconfigure xserver-xfree86
Section "Files"
FontPath "unix/:7100" # local font server
# if the local font server has problems, we can fall back on these
FontPath "/usr/lib/X11/fonts/misc"
FontPath "/usr/lib/X11/fonts/cyrillic"
FontPath "/usr/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/Type1"
FontPath "/usr/lib/X11/fonts/CID"
FontPath "/usr/lib/X11/fonts/Speedo"
FontPath "/usr/lib/X11/fonts/100dpi"
FontPath "/usr/lib/X11/fonts/75dpi"
EndSection
Section "Module"
Load "GLcore"
Load "bitmap"
Load "dbe"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "record"
Load "speedo"
Load "type1"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "ch"
Option "XkbVariant" "de"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/atibm"
Option "Protocol" "BusMouse"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Generic Mouse"
Driver "mouse"
Option "SendCoreEvents" "true"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
Section "Device"
Identifier "32"
Driver "fbdev"
BusID "1"
VideoRam 32
Option "UseFBDev" "true"
EndSection
Section "Monitor"
Identifier "Standardbildschirm"
HorizSync 28-50
VertRefresh 43-75
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "32"
Monitor "Standardbildschirm"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "Generic Mouse"
EndSection
Section "DRI"
Mode 0666
EndSection
Versuch's mal mit der: http://www.bitmuncher.de/files/XF86Config-4
bei deiner config kommt widermal
thomsti:~# startx
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
X: warning; process set to priority -1 instead of requested priority 0
XFree86 Version 4.3.0.1 (Debian 4.3.0.dfsg.1-14sarge1 20050901212727 fjp@localhost.localdomain)
Release Date: 15 August 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.6.8-16.0508-2 i686 [ELF]
Build Date: 02 September 2005
This version of XFree86 has been extensively modified by the Debian
Project, and is not supported by the XFree86 Project, Inc., in any
way. Bugs should be reported to the Debian Bug Tracking System; see
<URL: http://www.debian.org/Bugs/Reporting >.
We strongly encourage the use of the "reportbug" package and command
to ensure that bug reports contain as much useful information as
possible.
Before filing a bug report, you may want to consult the Debian X FAQ:
XHTML version: file:///usr/share/doc/xfree86-common/FAQ.xhtml
plain text version: file:///usr/share/doc/xfree86-common/FAQ.gz
Module Loader present
OS Kernel: Linux version 2.6.8-3-386 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Sat Jul 15 09:26:40 UTC 2006
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Oct 4 23:08:57 2006
(==) Using config file: "/etc/X11/XF86Config-4"
Skipping "/usr/X11R6/lib/modules/fonts/libspeedo.a:spencode.o": No symbols found
(EE) FBDEV(0): EGA/VGA planes are not yet supported by the fbdev driver [1]
free(): invalid pointer 0x836b154!
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
XIO: fatal IO error 104 (Connection reset by peer) on X server ":0.0"
after 0 requests (0 known processed) with 0 events remaining.
thomsti:~#
Dann hast du den Kernel-Framebuffer nicht an. Wenn dein Monitor eine Aufloesung von 1024x768 unterstuetzt, dann uebergib dem Kernel mal beim Booten den Parameter 'vga=0x317' (ohne Anfuehrungszeichen natuerlich).
????
was genau mus ich machen ? bin newbie und meine kiste ist meistens online
;-)
Im Grub-Menue 'e' druecken, zu der Zeile gehen, in der '/vmlinuz blabla bla' steht und dort ans Ende 'vga=0x317' einfuegen. Enter druecken und dann sollte deine Konsole eine hoehere Aufloesung bekommen (1024x768 bei 16bit).
hmm wen ich im grub e drücke kommt ein neues menü mit boot usw aber nichts mit /vmlinuz blablabla ;-) vileicht ist es empfelenswert das ich linux debian benüze ;-)
Du solltest dort aber eine Zeile der Form
kernel /vmlinuz-2.6.8-3-686 root=/dev/hda3 ro
haben. Dort an's Ende gehoeren die Kernel-Parameter. Alternativ kannst du das auch direkt in die /boot/grub/menu.lst einfuegen. Es empfiehlt sich dafuer aber den kompletten Abschnitt des Default-Kernels zu duplizieren und nur an einen der beiden gleichen Abschnitte den vga-Parameter anzufuegen. So hast du zur Not den Original-Eintrag noch zusaetzlich zur Verfuegung, falls die Aufloesung o.ae. bei dir nicht funktioniert.
ok habe diese datei gefunden und habe nochmals e gedrückt und die vga=0x317 eingefügt dan hat es so ausgesehen
kernel /vmlinuz-2.6.8-3-686 root=/dev/hda3 ro vga=0x317 leider hat dies fehlgeschlagen :-(
Was heisst fehlgeschlagen?
grafisches zeug geht immernoch nicht :-( wen ich startx mache kommt
thomsti:~# startx
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
Using authority file /root/.Xauthority
Writing authority file /root/.Xauthority
X: warning; process set to priority -1 instead of requested priority 0
XFree86 Version 4.3.0.1 (Debian 4.3.0.dfsg.1-14sarge1 20050901212727 fjp@localhost.localdomain)
Release Date: 15 August 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.6.8-16.0508-2 i686 [ELF]
Build Date: 02 September 2005
This version of XFree86 has been extensively modified by the Debian
Project, and is not supported by the XFree86 Project, Inc., in any
way. Bugs should be reported to the Debian Bug Tracking System; see
<URL: http://www.debian.org/Bugs/Reporting >.
We strongly encourage the use of the "reportbug" package and command
to ensure that bug reports contain as much useful information as
possible.
Before filing a bug report, you may want to consult the Debian X FAQ:
XHTML version: file:///usr/share/doc/xfree86-common/FAQ.xhtml
plain text version: file:///usr/share/doc/xfree86-common/FAQ.gz
Module Loader present
OS Kernel: Linux version 2.6.8-3-386 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Sat Jul 15 09:26:40 UTC 2006
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Thu Oct 5 00:18:15 2006
(==) Using config file: "/etc/X11/XF86Config-4"
Skipping "/usr/X11R6/lib/modules/fonts/libspeedo.a:spencode.o": No symbols found
(EE) FBDEV(0): EGA/VGA planes are not yet supported by the fbdev driver [1]
free(): invalid pointer 0x836b154!
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to submit@bugs.debian.org.
XIO: fatal IO error 104 (Connection reset by peer) on X server ":0.0"
after 0 requests (0 known processed) with 0 events remaining.
thomsti:~#
thomsti:~#
ich geh schlafen bis morgen ;-)
Das ist seltsam, dann kommen ja nur noch der Driver 'ati' oder 'vesa' in Frage. Einfach mal damit probieren, wuerde ich empfehlen, wobei es mich schon wundert, dass du diese Meldung immernoch bekommst, wenn deine Konsole eine Aufloesung von 1024x768 hat.
juhui mit vesa hats geklappppttttt :-D
Powered by vBulletin® Version 4.2.0 Copyright ©2013 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.