Suse 10.1 DVB-T USB Device Medion MD95700

Dieses Thema im Forum "SuSE / OpenSuSE" wurde erstellt von heili, 23.05.2006.

  1. heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    Hallo

    ich habe zur Zeit die Vesion Suse 10.1 installiert und nutze dieses für die tägliche arbeit.
    Habe das Problem das ich meinen vorhandenen dvb-t receiver medion md 95700 nun auch unter linux nutzen möchte.

    Deshalb die Frage, wer kann mir hier weiter helfen.

    gruss
    heili
     
  2. Anzeige

    Schau dir mal diese Kategorie an. Dort findest du bestimmt etwas.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  3. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen
    Leider beinhaltet dein Posting keine Informationen damit man dir Helfen könnte.

    Was hast du schon probiert, was geht nicht, wo hast du angesetzt, etc. pp. ...
     
  4. heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    habe mit modprobe

    modprobe cx22702
    modprobe dvb-usb

    die module hinzugefügt
    bei

    modprobe dvb-usb-cxusb kam die Fehlermeldung das er das modul nicht finden kann

    heili
     
  5. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen
    Woher hast du die Infos über die Module ? - Welchen Chipsatz verwendet die Karte ?
    Was spuckt das syslog aus in Bezug auf die Karte ?
     
  6. heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    habe die posts von Kulesza durchforst

    bzw in den links gestöbert worin stand das man diese module benötigt

    was das syslog sagt weiß ich leider nicht ,
    wäre nett wenn du mir veraten würdest wo ich es finden kann

    danke
    heili
     
  7. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen

    Poste mal die Ausgabe von
    Code:
    dmesg
    ... dann sehen wir weiter ;)
     
  8. #7 heili, 23.05.2006
    Zuletzt bearbeitet: 23.05.2006
    heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    naja das sind schon ein paar zeilen :-)
    habe darin aber nichts besonderes gefunden
    ausser das eben den dvbtreceiver nicht gefunden hat

    bzw hier hat er ja was gefunden

    usb 1-6.1: new high speed USB device using ehci_hcd and address 6
    usb 1-6.1: new device found, idVendor=1660, idProduct=0932
    usb 1-6.1: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-6.1: Product: USB Hybrid Video Capture
    usb 1-6.1: Manufacturer: Conexant
    usb 1-6.1: configuration #1 chosen from 1 choice
    usb 1-6.2: new low speed USB device using ehci_hcd and address 7
    usb 1-6.2: new device found, idVendor=0bc7, idProduct=0006
    usb 1-6.2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-6.2: Product: USB Receiver
    usb 1-6.2: Manufacturer: X10 Wireless Technology Inc
    usb 1-6.2: configuration #1 chosen from 1 choice
    usb 1-6.4: new high speed USB device using ehci_hcd and address 8
    lirc_dev: module not supported by Novell, setting U taint flag.
    lirc_dev: IR Remote Control driver registered, at major 61
    lirc_atiusb: module not supported by Novell, setting U taint flag.


    Code:
    Linux version 2.6.16.13-4-bigsmp (geeko@buildhost) (gcc version 4.1.0 (SUSE Linux)) #1 SMP Wed May 3 04:53:23 UTC 2006
    BIOS-provided physical RAM map:
     BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
     BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
     BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
     BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
     BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
     BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
     BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
     BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
     BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
    2175MB HIGHMEM available.
    896MB LOWMEM available.
    No mptable found.
    On node 0 totalpages: 786416
      DMA zone: 4096 pages, LIFO batch:0
      DMA32 zone: 0 pages, LIFO batch:0
      Normal zone: 225280 pages, LIFO batch:31
      HighMem zone: 557040 pages, LIFO batch:31
    DMI 2.2 present.
    Using APIC driver default
    ACPI: RSDP (v000 Nvidia                                ) @ 0x000f75c0
    ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0xbfff3000
    ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0xbfff3040
    ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0xbfff74c0
    ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x4008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Processor #0 6:10 APIC version 16
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    Overriding APIC driver with bigsmp
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: BIOS IRQ0 pin2 override ignored.
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
    ACPI: IRQ9 used by override.
    ACPI: IRQ14 used by override.
    ACPI: IRQ15 used by override.
    Enabling APIC mode:  Physflat.  Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
    Built 1 zonelists
    Kernel command line: root=/dev/hdb2 vga=0x317    resume=/dev/hdb1  splash=silent
    bootsplash: silent mode.
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Detected 1913.359 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 3109376k/3145664k available (1636k kernel code, 35064k reserved, 881k data, 192k init, 2228160k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3830.83 BogoMIPS (lpj=7661664)
    Security Framework v1.0.0 initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    checking if image is initramfs... it is
    Freeing initrd memory: 2334k freed
     not found!
    CPU0: AMD Athlon(tm) XP 2600+ stepping 00
    Leaving ESR disabled.
    Total of 1 processors activated (3830.83 BogoMIPS).
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
    Brought up 1 CPUs
    migration_cost=0
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=2
    PCI: Using configuration type 1
    ACPI: Subsystem revision 20060127
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: nForce2 C1 Halt Disconnect fixup
    Boot video device is 0000:02:00.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
    ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
    ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
    ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
    ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
    ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
    ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
    ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
    ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 16 devices
    PnPBIOS: Disabled by ACPI PNP
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
    TC classifier action (bugs to [email]netdev@vger.kernel.org[/email] cc [email]hadi@cyberus.ca[/email])
    Setting up standard PCI resources
    pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
    pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
    pnp: 00:00: ioport range 0x4400-0x447f has been reserved
    pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
    pnp: 00:00: ioport range 0x4200-0x427f has been reserved
    pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
    pnp: 00:01: ioport range 0x5000-0x503f has been reserved
    pnp: 00:01: ioport range 0x5500-0x553f has been reserved
    PCI: Bridge: 0000:00:08.0
      IO window: d000-dfff
      MEM window: e2000000-e3ffffff
      PREFETCH window: c4000000-c40fffff
    PCI: Bridge: 0000:00:1e.0
      IO window: disabled.
      MEM window: e0000000-e1ffffff
      PREFETCH window: d8000000-dfffffff
    PCI: Setting latency timer of device 0000:00:08.0 to 64
    apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
    apm: overridden by ACPI.
    audit: initializing netlink socket (disabled)
    audit(1148420748.576:1): initialized
    highmem bounce pool size: 64 pages
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 6144k, total 131072k
    vesafb: mode is 1024x768x16, linelength=2048, pages=1
    vesafb: protected mode interface info at c000:e340
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 47089 bytes,<6>...found (1024x768, 27542 bytes, v3).
    Console: switching to colour frame buffer device 124x44
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Real Time Clock Driver v1.12ac
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard as /class/input/input0
    input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
    input: PC Speaker as /class/input/input2
    md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 4.39
    NET: Registered protocol family 2
    IP route cache hash table entries: 131072 (order: 7, 524288 bytes)
    TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 524288 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    Using IPI No-Shortcut mode
    ACPI wakeup devices: 
    HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1 
    ACPI: (supports S0 S1 S4 S5)
    Freeing unused kernel memory: 192k freed
    Write protecting the kernel read-only data: 290k
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    NFORCE2: IDE controller at PCI slot 0000:00:09.0
    NFORCE2: chipset revision 162
    NFORCE2: not 100% native mode: will probe irqs later
    NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
    NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
        ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
        ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
    Probing IDE interface ide0...
    hda: IC35L120AVV207-0, ATA DISK drive
    hdb: Maxtor 6Y120L0, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hda: max request size: 512KiB
    hda: 241254720 sectors (123522 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
    hda: cache flushes supported
     hda: hda1 hda2 < hda5 hda6 >
    hdb: max request size: 128KiB
    hdb: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
    hdb: cache flushes supported
     hdb: hdb1 hdb2 hdb3
    Probing IDE interface ide1...
    hdc: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
    hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    Attempting manual resume
    ReiserFS: hdb2: found reiserfs format "3.6" with standard journal
    ReiserFS: hdb2: using ordered data mode
    reiserfs: using flush barriers
    ReiserFS: hdb2: journal params: device hdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: hdb2: checking transaction log (hdb2)
    ReiserFS: hdb2: Using r5 hash to sort names
    Adding 1052216k swap on /dev/hdb1.  Priority:-1 extents:1 across:1052216k
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x278 (0x678), irq 5, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    lp0: using parport0 (interrupt-driven).
    r8169 Gigabit Ethernet driver 2.2LK loaded
    gameport: NS558 PnP Gameport is pnp00:0f/gameport0, io 0x201, speed 701kHz
    ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
    ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 177
    eth0: Identified chip type is 'RTL8169s/8110s'.
    eth0: RTL8169 at 0xf887e000, 00:50:fc:f4:fb:a2, IRQ 177
    ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:06.0 to 64
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    intel8x0_measure_ac97_clock: measured 56046 usecs
    intel8x0: clocking to 47474
    ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
    ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 193
    PCI: Setting latency timer of device 0000:00:02.2 to 64
    ehci_hcd 0000:00:02.2: EHCI Host Controller
    ehci_hcd 0000:00:02.2: debug port 1
    PCI: cache line size of 64 is not supported by device 0000:00:02.2
    ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:02.2: irq 193, io mem 0xe4003000
    ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: new device found, idVendor=0000, idProduct=0000
    usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb1: Product: EHCI Host Controller
    usb usb1: Manufacturer: Linux 2.6.16.13-4-bigsmp ehci_hcd
    usb usb1: SerialNumber: 0000:00:02.2
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 201
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    ohci_hcd 0000:00:02.0: OHCI Host Controller
    ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:02.0: irq 201, io mem 0xe4001000
    usb usb2: new device found, idVendor=0000, idProduct=0000
    usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb2: Product: OHCI Host Controller
    usb usb2: Manufacturer: Linux 2.6.16.13-4-bigsmp ohci_hcd
    usb usb2: SerialNumber: 0000:00:02.0
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 3 ports detected
    usb 1-1: new high speed USB device using ehci_hcd and address 2
    ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 22 (level, high) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:02.1 to 64
    ohci_hcd 0000:00:02.1: OHCI Host Controller
    ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
    ohci_hcd 0000:00:02.1: irq 185, io mem 0xe4002000
    usb 1-1: new device found, idVendor=04cc, idProduct=1520
    usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    usb usb3: new device found, idVendor=0000, idProduct=0000
    usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb3: Product: OHCI Host Controller
    usb usb3: Manufacturer: Linux 2.6.16.13-4-bigsmp ohci_hcd
    usb usb3: SerialNumber: 0000:00:02.1
    hub 1-1:1.0: 4 ports detected
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 3 ports detected
    hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Linux agpgart interface v0.101 (c) Dave Jones
    i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
    i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5500
    agpgart: Detected NVIDIA nForce2 chipset
    agpgart: AGP aperture is 128M @ 0xd0000000
    usb 1-6: new high speed USB device using ehci_hcd and address 4
    usb 1-6: new device found, idVendor=04b4, idProduct=6560
    usb 1-6: new device strings: Mfr=0, Product=0, SerialNumber=0
    usb 1-6: configuration #1 chosen from 1 choice
    hub 1-6:1.0: USB hub found
    hub 1-6:1.0: 4 ports detected
    ohci_hcd 0000:00:02.0: wakeup
    device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email]dm-devel@redhat.com[/email]
    dm-netlink version 0.0.2 loaded
    usb 1-1.1: new full speed USB device using ehci_hcd and address 5
    usb 1-1.1: new device found, idVendor=0403, idProduct=fc82
    usb 1-1.1: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 1-1.1: Product: SEMC DSS-20 SyncStation
    usb 1-1.1: Manufacturer: Sony Ericsson
    usb 1-1.1: SerialNumber: 00007QEX
    usb 1-1.1: configuration #1 chosen from 1 choice
    usb 1-6.1: new high speed USB device using ehci_hcd and address 6
    usb 1-6.1: new device found, idVendor=1660, idProduct=0932
    usb 1-6.1: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-6.1: Product: USB Hybrid Video Capture
    usb 1-6.1: Manufacturer: Conexant
    usb 1-6.1: configuration #1 chosen from 1 choice
    usb 1-6.2: new low speed USB device using ehci_hcd and address 7
    usb 1-6.2: new device found, idVendor=0bc7, idProduct=0006
    usb 1-6.2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-6.2: Product: USB Receiver
    usb 1-6.2: Manufacturer: X10 Wireless Technology Inc
    usb 1-6.2: configuration #1 chosen from 1 choice
    usb 1-6.4: new high speed USB device using ehci_hcd and address 8
    lirc_dev: module not supported by Novell, setting U taint flag.
    lirc_dev: IR Remote Control driver registered, at major 61 
    lirc_atiusb: module not supported by Novell, setting U taint flag.
    
    lirc_atiusb: USB remote driver for LIRC v0.5
    lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
    usb 1-6.4: new device found, idVendor=0dda, idProduct=2005
    usb 1-6.4: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 1-6.4: Product: 2.0 Card Reader
    usb 1-6.4: Manufacturer: USB Reader
    usb 1-6.4: SerialNumber: ABCD12345678
    usb 1-6.4: configuration #1 chosen from 1 choice
    usbcore: registered new driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
    SCSI subsystem initialized
    Initializing USB Mass Storage driver...
    usb 2-2: new full speed USB device using ohci_hcd and address 2
    usb 2-2: new device found, idVendor=04a7, idProduct=0331
    usb 2-2: new device strings: Mfr=4, Product=7, SerialNumber=0
    usb 2-2: Product: OneTouch 8600 EPP/USB
    usb 2-2: Manufacturer: Visioneer
    usb 2-2: configuration #1 chosen from 1 choice
    usbcore: registered new driver usbserial_generic
    drivers/usb/serial/usb-serial.c: USB Serial Driver core
    lirc_dev: lirc_register_plugin: sample_rate: 0
    lirc_atiusb[7]: X10 Wireless Technology Inc USB Receiver on usb1:7
    drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
    usbcore: registered new driver lirc_atiusb
    scsi0 : SCSI emulation for USB Mass Storage devices
    ftdi_sio 1-1.1:1.0: FTDI USB Serial Device converter detected
    drivers/usb/serial/ftdi_sio.c: Detected FT232BM
    usb-storage: device found at 8
    usb-storage: waiting for device to settle before scanning
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb 1-1.1: FTDI USB Serial Device converter now attached to ttyUSB0
    usbcore: registered new driver ati_remote
    drivers/usb/input/ati_remote.c: Registered USB driver ATI/X10 RF USB Remote Control v. 2.2.1
    usbcore: registered new driver ftdi_sio
    drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
      Vendor: USB Read  Model: CF Card       CF  Rev: 1.8D
      Type:   Direct-Access                      ANSI SCSI revision: 00
      Vendor: USB Read  Model: MS card       MS  Rev: 1.8D
      Type:   Direct-Access                      ANSI SCSI revision: 00
    Driver 'sd' needs updating - please use bus_type methods
      Vendor: USB Read  Model: SD card   MMC/SD  Rev: 1.8D
      Type:   Direct-Access                      ANSI SCSI revision: 00
      Vendor: USB Read  Model: SM card       SM  Rev: 1.8D
      Type:   Direct-Access                      ANSI SCSI revision: 00
    sd 0:0:0:0: Attached scsi removable disk sda
    sd 0:0:0:1: Attached scsi removable disk sdb
    usb-storage: device scan complete
    SCSI device sdc: 1000448 512-byte hdwr sectors (512 MB)
    sdc: Write Protect is off
    sdc: Mode Sense: 4b 00 00 08
    sdc: assuming drive cache: write through
    SCSI device sdc: 1000448 512-byte hdwr sectors (512 MB)
    sdc: Write Protect is off
    sdc: Mode Sense: 4b 00 00 08
    sdc: assuming drive cache: write through
     sdc: sdc1
    sd 0:0:0:2: Attached scsi removable disk sdc
    sd 0:0:0:3: Attached scsi removable disk sdd
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sd 0:0:0:1: Attached scsi generic sg1 type 0
    sd 0:0:0:2: Attached scsi generic sg2 type 0
    sd 0:0:0:3: Attached scsi generic sg3 type 0
    loop: loaded (max 8 devices)
    ReiserFS: hdb3: found reiserfs format "3.6" with standard journal
    ReiserFS: hdb3: using ordered data mode
    reiserfs: using flush barriers
    ReiserFS: hdb3: journal params: device hdb3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: hdb3: checking transaction log (hdb3)
    ReiserFS: hdb3: Using r5 hash to sort names
    NTFS driver 2.1.26 [Flags: R/W MODULE].
    NTFS volume version 3.1.
    NTFS volume version 3.1.
    NTFS volume version 3.1.
    AppArmor: AppArmor (version 2.0-19.43r6320) initialized
    audit(1148420780.182:2): AppArmor (version 2.0-19.43r6320) initialized
    
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 2.4 (8192 buckets, 65536 max) - 216 bytes per conntrack
    ACPI: Power Button (FF) [PWRF]
    ACPI: Power Button (CM) [PWRB]
    BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
    r8169: eth0: link up
    powernow-k8: Processor cpuid 6a0 not supported
    eth0: no IPv6 routers present
    vmmon: module not supported by Novell, setting U taint flag.
    vmmon: module license 'unspecified' taints kernel.
    /dev/vmmon[3860]: Module vmmon: registered with major=10 minor=165
    /dev/vmmon[3860]: Module vmmon: initialized
    vmnet: module not supported by Novell, setting U taint flag.
    /dev/vmnet: open called by PID 3896 (vmnet-bridge)
    /dev/vmnet: hub 0 does not exist, allocating memory.
    /dev/vmnet: port on hub 0 successfully opened
    bridge-eth0: enabling the bridge
    bridge-eth0: up
    bridge-eth0: already up
    bridge-eth0: attached
    novfs: module not supported by Novell, setting U taint flag.
    bootsplash: status on console 0 changed to on
    SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.15.7 DST=224.0.0.251 LEN=109 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=89 
    Linux video capture interface: v1.00
    bttv: driver version 0.9.16 loaded
    bttv: using 8 buffers with 2080k (520 pages) each for capture
    st: Version 20050830, fixed bufsize 32768, s/g segs 256
    
     
  9. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen
    Ist das der Auszug nachdem du modprober der beiden Treiber gemacht hattest ?
    /lib/modules/2.6.16.13-4-default/kernel/drivers/media/dvb/frontends/cx22702.ko
    /lib/modules/2.6.16.13-4-default/kernel/drivers/media/dvb/dvb-usb/dvb-usb-cxusb.ko

    Falls ja, scheint deine TV Karte nicht diesen Chipsatz zu nutzen!
    Poste dann mal die Ausgabe von
    Code:
    lscpi -v
     
  10. heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    /lib/modules/2.6.16.13-4-default/kernel/drivers/media/dvb/dvb-usb/dvb-usb-cxusb.ko

    kann nicht gefunden werden

    lscpi kann auch nciht gefunden werden
     
  11. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen
    Dann solltest du mal den Kernel-default reinstallieren .. bei mir ist unter SuSE 10.1 diese Datei vorhanden ;)


    PS: lspci als root ausführen !
     
  12. heili

    heili Grünschnabel

    Dabei seit:
    23.05.2006
    Beiträge:
    6
    Zustimmungen:
    0
    buchstabendreher lspci geht natürlich, zeigt aber eben nur die pci geschichten an

    uind da ist nichts außergewöhnliches ( grafikkarte , mainboard, chipsatz etc)
     
  13. Anzeige

    Vielleicht findest du HIER Antworten.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  14. #12 Moenderman, 22.02.2007
    Moenderman

    Moenderman Grünschnabel

    Dabei seit:
    22.02.2007
    Beiträge:
    6
    Zustimmungen:
    0
    Komme nicht weiter - Hilfe bitte MD 95700

    Hallo,

    habe mich jetzt durch alle möglichen Google-Treffer zu "MD 95700 Linux" durchgelesen, aber ich komme nicht weiter.

    lsusb ergibt bei mir folgendes:
    Bus 001 Device 004: ID 046d:c501 Logitech, Inc. Cordless Mouse Receiver
    Bus 001 Device 005: ID 046d:c503 Logitech, Inc. Cordless Mouse+Keyboard Receiver
    Bus 001 Device 001: ID 0000:0000
    Bus 002 Device 002: ID 0db0:6982 Micro Star International Medion Flash XL V2.7A Card Reader
    Bus 002 Device 003: ID 04b8:0005 Seiko Epson Corp. Stylus Printer
    Bus 002 Device 001: ID 0000:0000
    Bus 005 Device 004: ID 043d:007b Lexmark International, Inc.
    Bus 005 Device 003: ID 043d:007c Lexmark International, Inc.
    Bus 005 Device 002: ID 043d:007a Lexmark International, Inc.
    Bus 005 Device 001: ID 0000:0000
    Bus 004 Device 021: ID 0bc7:0006 X10 Wireless Technology, Inc.
    Bus 004 Device 020: ID 1660:0932
    Bus 004 Device 019: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub"
    Bus 004 Device 001: ID 0000:0000
    Bus 003 Device 001: ID 0000:0000

    Wie muss ich modprobe als SU genau eingeben? Da kommt bei mir gar nichts.

    Ich möchte diese Ding endlich zum Laufen kriegen, (besser bekriegen!!!!) aber ich bin mit meinem Linux-Anfangslatein am Ende.

    Danke für die HILFE!!!
     
  15. devilz

    devilz Pro*phet
    Administrator

    Dabei seit:
    01.05.2002
    Beiträge:
    12.244
    Zustimmungen:
    0
    Ort:
    Hessen
    @Moenderman

    Naja, ich sehe in deiner lspci Ausgabe nicht das Device ;)
    Ist das ein USB Gerät?
     
Thema: Suse 10.1 DVB-T USB Device Medion MD95700
Besucher kamen mit folgenden Suchen
  1. medion md 95700 specs

    ,
  2. medion med md 95700 treiber

Die Seite wird geladen...

Suse 10.1 DVB-T USB Device Medion MD95700 - Ähnliche Themen

  1. DVB-T-USB-Sticks unter openSuSE 10.3

    DVB-T-USB-Sticks unter openSuSE 10.3: Hallo zusammen! Ich habe mir vor kurzem openSuSE 10.3 gekauft und habe mich bereits recht gut mit dem OS angefreundet. Da ich keinen Fernseher...
  2. Hama DVB-t Stick unter SuSE 10.2

    Hama DVB-t Stick unter SuSE 10.2: Moin leuts, Hat einer von euch ne Idee ob und wenn ja wo es Treiber für den "Hama DVB-t USB 2.0" Stick gibt? Ich haatte bisher bei meiner Suche...
  3. welcher DVB-T Stick für Suse 10.2

    welcher DVB-T Stick für Suse 10.2: Hallo zusammen, hat jemand Erfahrung mit einem DVB-T USB-Stick, der unter openSuse 10.2 läuft? schon mal vielen Dank trapper
  4. SUSE 10.0 und Installation von DVB-T USB-Sticks?

    SUSE 10.0 und Installation von DVB-T USB-Sticks?: Hallo, habe jetzt einige Sticks ausprobiert - es ist zum Verzweifeln! Nach einem ANUBIS(PLUS-Angebot)-, Grandtec(Conrad.de)-Stick raetsele...
  5. Twinhan DVB-T in SuSE 10.0 installieren

    Twinhan DVB-T in SuSE 10.0 installieren: Hallo, ich hab ein Problemchen... Ich hab auf meinem Notebook SuSE 10.0 installiert und wollte jetzt "nur noch schnell" meinen USB TV-Adapter zum...