komme mit openSuse 11 nicht ins Internet

Dieses Thema im Forum "SuSE / OpenSuSE" wurde erstellt von Olaf_S, 24.11.2008.

  1. Olaf_S

    Olaf_S Guest

    Hallo zusammen,

    ich bin was die Linux-Administration angeht ein Anfänger. Bisher war ich immer als User unter Unix unterwegs.

    Nun ist meine Frage, wie ich die Netzwerkkarte und das DSL unter SUSE 11 so zulaufen kriege, das ich ins Internet komme.

    Gruss Olaf
    :hilfe2:
     
  2. Anzeige

    Schau dir mal diese Kategorie an. Dort findest du bestimmt etwas.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  3. #2 Jonny Mulandros, 24.11.2008
    Jonny Mulandros

    Jonny Mulandros Doppel-As

    Dabei seit:
    12.05.2007
    Beiträge:
    128
    Zustimmungen:
    0
    Ort:
    Kiel
    Ähm, also ein paar mehr Infos wären schon angebracht!
    Hardware?
    z.B. welche Netzwerkkarte? Korrekt erkannt oder Treiber installiert?
    Modem- oder Routerverbindung?
    Am besten mal die Ausgaben von
    Code:
    dmesg
    
    sowie
    Code:
    ifconfig
    
    hier posten!

    Dann sehen wir weiter!
     
  4. #3 Always-Godlike, 24.11.2008
    Always-Godlike

    Always-Godlike Das Freak

    Dabei seit:
    31.12.2006
    Beiträge:
    939
    Zustimmungen:
    0
    Ort:
    Saarland
    Yast > Hardware > Netzwerkkarte
     
  5. Olaf_S

    Olaf_S Guest

    Hallo, hier sind die beiden Ergebnisse:

    demsg:
    Linux version 2.6.25.5-1.1-default (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-06-07 01:55:22 +0200
    Command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_HD502IJS13TJ1MQ800462-part2 resume=/dev/sda1 splash=silent vga=0x317
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 00000000cffc0000 (usable)
    BIOS-e820: 00000000cffc0000 - 00000000cffce000 (ACPI data)
    BIOS-e820: 00000000cffce000 - 00000000cfff0000 (ACPI NVS)
    BIOS-e820: 00000000cfff0000 - 00000000cfffe000 (reserved)
    BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
    BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
    Entering add_active_range(0, 0, 159) 0 entries of 3200 used
    Entering add_active_range(0, 256, 851904) 1 entries of 3200 used
    Entering add_active_range(0, 1048576, 1245184) 2 entries of 3200 used
    end_pfn_map = 1245184
    DMI present.
    ACPI: RSDP 000FAF60, 0014 (r0 ACPIAM)
    ACPI: RSDT CFFC0000, 003C (r1 122107 RSDT0947 20071221 MSFT 97)
    ACPI: FACP CFFC0200, 0084 (r2 122107 FACP0947 20071221 MSFT 97)
    ACPI: DSDT CFFC0440, 6E9B (r1 1ADNC 1ADNC001 1 INTL 20051117)
    ACPI: FACS CFFCE000, 0040
    ACPI: APIC CFFC0390, 006C (r1 122107 APIC0947 20071221 MSFT 97)
    ACPI: MCFG CFFC0400, 003C (r1 122107 OEMMCFG 20071221 MSFT 97)
    ACPI: OEMB CFFCE040, 0071 (r1 122107 OEMB0947 20071221 MSFT 97)
    ACPI: HPET CFFC72E0, 0038 (r1 122107 OEMHPET 20071221 MSFT 97)
    ACPI: SSDT CFFC7320, 0544 (r1 A M I POWERNOW 1 AMD 1)
    Scanning NUMA topology in Northbridge 24
    No NUMA configuration found
    Faking a node at 0000000000000000-0000000130000000
    Entering add_active_range(0, 0, 159) 0 entries of 3200 used
    Entering add_active_range(0, 256, 851904) 1 entries of 3200 used
    Entering add_active_range(0, 1048576, 1245184) 2 entries of 3200 used
    Bootmem setup node 0 0000000000000000-0000000130000000
    NODE_DATA [000000000000e000 - 0000000000015fff]
    bootmap [0000000000016000 - 000000000003bfff] pages 26
    early res: 0 [0-fff] BIOS data page
    early res: 1 [6000-7fff] SMP_TRAMPOLINE
    early res: 2 [200000-8b5bd7] TEXT DATA BSS
    early res: 3 [37a73000-37fef253] RAMDISK
    early res: 4 [9fc00-a0bff] EBDA
    early res: 5 [8000-dfff] PGTABLE
    [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
    [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
    [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
    [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
    [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
    [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
    [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
    [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
    [ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
    [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
    [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
    [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
    [ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
    [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
    [ffffe20001c00000-ffffe20001dfffff] PMD ->ffff810004a00000 on node 0
    [ffffe20001e00000-ffffe20001ffffff] PMD ->ffff810004e00000 on node 0
    [ffffe20002000000-ffffe200021fffff] PMD ->ffff810005200000 on node 0
    [ffffe20002200000-ffffe200023fffff] PMD ->ffff810005600000 on node 0
    [ffffe20002400000-ffffe200025fffff] PMD ->ffff810005a00000 on node 0
    [ffffe20002600000-ffffe200027fffff] PMD ->ffff810005e00000 on node 0
    [ffffe20002800000-ffffe200029fffff] PMD ->ffff810006200000 on node 0
    [ffffe20002a00000-ffffe20002bfffff] PMD ->ffff810006600000 on node 0
    [ffffe20002c00000-ffffe20002dfffff] PMD ->ffff810006a00000 on node 0
    [ffffe20003800000-ffffe200039fffff] PMD ->ffff810006e00000 on node 0
    [ffffe20003a00000-ffffe20003bfffff] PMD ->ffff810007200000 on node 0
    [ffffe20003c00000-ffffe20003dfffff] PMD ->ffff810007600000 on node 0
    [ffffe20003e00000-ffffe20003ffffff] PMD ->ffff810007a00000 on node 0
    [ffffe20004000000-ffffe200041fffff] PMD ->ffff810007e00000 on node 0
    [ffffe20004200000-ffffe200043fffff] PMD ->ffff810008200000 on node 0
    Zone PFN ranges:
    DMA 0 -> 4096
    DMA32 4096 -> 1048576
    Normal 1048576 -> 1245184
    Movable zone start PFN for each node
    early_node_map[3] active PFN ranges
    0: 0 -> 159
    0: 256 -> 851904
    0: 1048576 -> 1245184
    On node 0 totalpages: 1048415
    DMA zone: 56 pages used for memmap
    DMA zone: 1729 pages reserved
    DMA zone: 2214 pages, LIFO batch:0
    DMA32 zone: 14280 pages used for memmap
    DMA32 zone: 833528 pages, LIFO batch:31
    Normal zone: 2688 pages used for memmap
    Normal zone: 193920 pages, LIFO batch:31
    Movable zone: 0 pages used for memmap
    ATI board detected. Disabling timer routing over 8254.
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 (Bootup-CPU)
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1
    ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    Processor #2
    ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    Processor #3
    ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Setting APIC routing to flat
    ACPI: HPET id: 0x8300 base: 0xfed00000
    Using ACPI (MADT) for SMP configuration information
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
    PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
    PM: Registered nosave memory: 00000000cffc0000 - 00000000cffce000
    PM: Registered nosave memory: 00000000cffce000 - 00000000cfff0000
    PM: Registered nosave memory: 00000000cfff0000 - 00000000cfffe000
    PM: Registered nosave memory: 00000000cfffe000 - 00000000ff700000
    PM: Registered nosave memory: 00000000ff700000 - 0000000100000000
    Allocating PCI resources starting at d0000000 (gap: cfffe000:2f702000)
    SMP: Allowing 4 CPUs, 0 hotplug CPUs
    PERCPU: Allocating 47936 bytes of per cpu data
    Built 1 zonelists in Node order, mobility grouping on. Total pages: 1029662
    Policy zone: Normal
    Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_HD502IJS13TJ1MQ800462-part2 resume=/dev/sda1 splash=silent vga=0x317
    bootsplash: silent mode.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 32768 bytes)
    TSC calibrated against PM_TIMER
    time.c: Detected 2200.158 MHz processor.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Checking aperture...
    Node 0: aperture @ 5008000000 size 32 MB
    Aperture beyond 4GB. Ignoring.
    No AGP bridge found
    Your BIOS doesn't leave a aperture memory hole
    Please enable the IOMMU option in the BIOS setup
    This costs you 64 MB of RAM
    Mapping aperture over 65536 KB of RAM @ c000000
    PM: Registered nosave memory: 000000000c000000 - 0000000010000000
    Memory: 4055664k/4980736k available (2365k kernel code, 137996k reserved, 1920k data, 404k init)
    CPA: page pool initialized 1 of 1 pages preallocated
    hpet clockevent registered
    Calibrating delay using timer specific routine.. 4585.75 BogoMIPS (lpj=9171503)
    Security Framework initialized
    AppArmor: AppArmor initialized <NULL>
    AppArmor: Registered secondary security module capability
    Capability LSM initialized as secondary
    Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Mount-cache hash table entries: 256
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 0/0 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    ACPI: Core revision 20070126
    ACPI: Checking initramfs for custom DSDT
    Parsing all Control Methods:
    Table [DSDT](id 0001) - 891 Objects with 66 Devices 259 Methods 21 Regions
    Parsing all Control Methods:
    Table [SSDT](id 0002) - 20 Objects with 0 Devices 0 Methods 0 Regions
    tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
    evxfevnt-0091 [00] enable : Transition to ACPI mode successful
    Using local APIC timer interrupts.
    APIC timer calibration result 12500887
    Detected 12.500 MHz APIC timer.
    Booting processor 1/4 APIC 0x1
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 4400.56 BogoMIPS (lpj=8801133)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 1/1 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    AMD Phenom(tm) 9500 Quad-Core Processor stepping 02
    checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    Booting processor 2/4 APIC 0x2
    Initializing CPU#2
    Calibrating delay using timer specific routine.. 4400.43 BogoMIPS (lpj=8800868)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 2/2 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 2
    AMD Phenom(tm) 9500 Quad-Core Processor stepping 02
    checking TSC synchronization [CPU#0 -> CPU#2]: passed.
    Booting processor 3/4 APIC 0x3
    Initializing CPU#3
    Calibrating delay using timer specific routine.. 4400.43 BogoMIPS (lpj=8800866)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 3/3 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 3
    AMD Phenom(tm) 9500 Quad-Core Processor stepping 02
    checking TSC synchronization [CPU#0 -> CPU#3]: passed.
    Brought up 4 CPUs
    CPU0 attaching sched-domain:
    domain 0: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000004 00000000,00000000,00000000,00000008
    domain 1: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,0000000f
    CPU1 attaching sched-domain:
    domain 0: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000004 00000000,00000000,00000000,00000008 00000000,00000000,00000000,00000001
    domain 1: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,0000000f
    CPU2 attaching sched-domain:
    domain 0: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,00000004 00000000,00000000,00000000,00000008 00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000002
    domain 1: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,0000000f
    CPU3 attaching sched-domain:
    domain 0: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,00000008 00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000004
    domain 1: span 00000000,00000000,00000000,0000000f
    groups: 00000000,00000000,00000000,0000000f
    net_namespace: 1016 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
    PCI: Not using MMCONFIG.
    PCI: Using configuration type 1
    evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
    evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 11 Runtime GPEs in this block
    ACPI: EC: Look up EC in DSDT
    Completing Region/Field/Buffer/Package initialization:................................................................................................................................
    Initialized 14/21 Regions 26/26 Fields 38/38 Buffers 50/52 Packages (920 nodes)
    Initializing Device/Processor/Thermal objects by executing _INI methods:..
    Executed 2 _INI methods requiring 0 _STA executions (examined 76 objects)
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: Error attaching device data
    ACPI: Error attaching device data
    ACPI: Error attaching device data
    ACPI: Error attaching device data
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:12.0: set SATA to AHCI mode
    PCI: Transparent bridge - 0000:00:14.4
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE9._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 *15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 7 10 11 12 14 15)
    ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - C3, should be C2 [20070126]
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 14 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    PCI-DMA: Disabling AGP.
    PCI-DMA: aperture base @ c000000 size 65536 KB
    PCI-DMA: using GART IOMMU.
    PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    hpet0: 4 32-bit timers, 14318180 Hz
    AppArmor: AppArmor Filesystem Enabled
    ACPI: RTC can wake from S4
    Switched to high resolution mode on CPU 0
    Switched to high resolution mode on CPU 3
    Switched to high resolution mode on CPU 2
    Switched to high resolution mode on CPU 1
    system 00:07: iomem range 0xfec00000-0xfec00fff has been reserved
    system 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved
    system 00:08: ioport range 0x4d0-0x4d1 has been reserved
    system 00:08: ioport range 0x40b-0x40b has been reserved
    system 00:08: ioport range 0x4d6-0x4d6 has been reserved
    system 00:08: ioport range 0xc00-0xc01 has been reserved
    system 00:08: ioport range 0xc14-0xc14 has been reserved
    system 00:08: ioport range 0xc50-0xc51 has been reserved
    system 00:08: ioport range 0xc52-0xc52 has been reserved
    system 00:08: ioport range 0xc6c-0xc6c has been reserved
    system 00:08: ioport range 0xc6f-0xc6f has been reserved
    system 00:08: ioport range 0xcd0-0xcd1 has been reserved
    system 00:08: ioport range 0xcd2-0xcd3 has been reserved
    system 00:08: ioport range 0xcd4-0xcd5 has been reserved
    system 00:08: ioport range 0xcd6-0xcd7 has been reserved
    system 00:08: ioport range 0xcd8-0xcdf has been reserved
    system 00:08: ioport range 0x800-0x89f has been reserved
    system 00:08: ioport range 0xb10-0xb1f has been reserved
    system 00:08: ioport range 0x900-0x90f has been reserved
    system 00:08: ioport range 0x910-0x91f has been reserved
    system 00:08: ioport range 0xfe00-0xfefe has been reserved
    system 00:08: iomem range 0xffb80000-0xffbfffff could not be reserved
    system 00:0b: ioport range 0x600-0x6df has been reserved
    system 00:0b: ioport range 0xae0-0xaef has been reserved
    system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
    system 00:0d: iomem range 0x0-0x9ffff could not be reserved
    system 00:0d: iomem range 0xc0000-0xcffff has been reserved
    system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
    system 00:0d: iomem range 0x100000-0xcfffffff could not be reserved
    system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved
    PCI: Bridge: 0000:00:02.0
    IO window: c000-cfff
    MEM window: 0xf7e00000-0xf7efffff
    PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
    PCI: Bridge: 0000:00:05.0
    IO window: d000-dfff
    MEM window: 0xf7f00000-0xf7ffffff
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:09.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:14.4
    IO window: e000-efff
    MEM window: 0xf8000000-0xfebfffff
    PREFETCH window: disabled.
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    PCI: Setting latency timer of device 0000:00:05.0 to 64
    PCI: Setting latency timer of device 0000:00:09.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 524288 bind 65536)
    TCP reno registered
    Unpacking initramfs... done
    Freeing initrd memory: 5616k freed
    audit: initializing netlink socket (disabled)
    type=2000 audit(1228128919.616:1): initialized
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:01:00.0: Boot video device
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:02.0:pcie00]
    PCI: Setting latency timer of device 0000:00:05.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:05.0:pcie00]
    PCI: Setting latency timer of device 0000:00:09.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:09.0:pcie00]
    vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20001080000, using 6144k, total 16384k
    vesafb: mode is 1024x768x16, linelength=2048, pages=9
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    bootsplash 3.1.6-2004/03/31: looking for picture...
    bootsplash: silentjpeg size 166113 bytes
    bootsplash: ...found (1024x768, 154167 bytes, v3).
    Console: switching to colour frame buffer device 124x44
    fb0: VESA VGA frame buffer device
    hpet_resources: 0xfed00000 is busy
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.103
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    input: PC Speaker as /devices/platform/pcspkr/input/input1
    logips2pp: Detected unknown logitech mouse model 115
    input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input2
    cpuidle: using governor ladder
    cpuidle: using governor menu
    NET: Registered protocol family 1
    registered taskstats version 1
    Freeing unused kernel memory: 404k freed
    Write protecting the kernel read-only data: 1680k
    ACPI: duty_cycle spans bit 4
    ACPI: ACPI0007:00 is registered as cooling_device0
    ACPI: ACPI0007:01 is registered as cooling_device1
    ACPI: ACPI0007:02 is registered as cooling_device2
    ACPI: ACPI0007:03 is registered as cooling_device3
    No dock devices found.
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:14.1 to 64
    scsi0 : pata_atiixp
    scsi1 : pata_atiixp
    ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
    ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
    ahci 0000:00:12.0: version 3.0
    ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
    ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
    ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP
    ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum part
    scsi2 : ahci
    scsi3 : ahci
    scsi4 : ahci
    scsi5 : ahci
    ata3: SATA max UDMA/133 abar m1024@0xf7dff800 port 0xf7dff900 irq 22
    ata4: SATA max UDMA/133 abar m1024@0xf7dff800 port 0xf7dff980 irq 22
    ata5: SATA max UDMA/133 abar m1024@0xf7dff800 port 0xf7dffa00 irq 22
    ata6: SATA max UDMA/133 abar m1024@0xf7dff800 port 0xf7dffa80 irq 22
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: ATA-7: SAMSUNG HD502IJ, 1AA01113, max UDMA7
    ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
    ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata3.00: configured for UDMA/133
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata4.00: ATA-7: SAMSUNG HD502IJ, 1AA01113, max UDMA7
    ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
    ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata4.00: configured for UDMA/133
    ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata5.00: ATAPI: TSSTcorp CDDVDW SH-S203N, SB00, max UDMA/100, ATAPI AN
    ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    ata5.00: configured for UDMA/100
    ata6: SATA link down (SStatus 0 SControl 300)
    scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1AA0 PQ: 0 ANSI: 5
    scsi 3:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1AA0 PQ: 0 ANSI: 5
    scsi 4:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S203N SB00 PQ: 0 ANSI: 5
    BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
    Driver 'sd' needs updating - please use bus_type methods
    sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    sda:<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
    ohci_hcd 0000:00:13.0: OHCI Host Controller
    ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
    sda1 sda2 sda3
    ohci_hcd 0000:00:13.0: irq 16, io mem 0xf7dfe000
    sd 2:0:0:0: [sda] Attached SCSI disk
    sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
    sd 3:0:0:0: [sdb] Write Protect is off
    sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
    sd 3:0:0:0: [sdb] Write Protect is off
    sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sdb: sdb1 sdb2
    sd 3:0:0:0: [sdb] Attached SCSI disk
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb1: Product: OHCI Host Controller
    usb usb1: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
    usb usb1: SerialNumber: 0000:00:13.0
    ACPI: PCI Interrupt 0000:00:13.1 -> GSI 17 (level, low) -> IRQ 17
    ohci_hcd 0000:00:13.1: OHCI Host Controller
    ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:13.1: irq 17, io mem 0xf7dfd000
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb2: Product: OHCI Host Controller
    usb usb2: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
    usb usb2: SerialNumber: 0000:00:13.1
    ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
    ohci_hcd 0000:00:13.2: OHCI Host Controller
    ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
    ohci_hcd 0000:00:13.2: irq 18, io mem 0xf7dfc000
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb3: Product: OHCI Host Controller
    usb usb3: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
    usb usb3: SerialNumber: 0000:00:13.2
    ACPI: PCI Interrupt 0000:00:13.3 -> GSI 17 (level, low) -> IRQ 17
    ohci_hcd 0000:00:13.3: OHCI Host Controller
    ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
    ohci_hcd 0000:00:13.3: irq 17, io mem 0xf7dfb000
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb4: Product: OHCI Host Controller
    usb usb4: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
    usb usb4: SerialNumber: 0000:00:13.3
    ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
    ohci_hcd 0000:00:13.4: OHCI Host Controller
    ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
    ohci_hcd 0000:00:13.4: irq 18, io mem 0xf7dfa000
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb5: Product: OHCI Host Controller
    usb usb5: Manufacturer: Linux 2.6.25.5-1.1-default ohci_hcd
    usb usb5: SerialNumber: 0000:00:13.4
    ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
    ehci_hcd 0000:00:13.5: EHCI Host Controller
    ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
    ehci_hcd 0000:00:13.5: debug port 1
    ehci_hcd 0000:00:13.5: irq 19, io mem 0xf7dff000
    ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb6: configuration #1 chosen from 1 choice
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 10 ports detected
    usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
    usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb6: Product: EHCI Host Controller
    usb usb6: Manufacturer: Linux 2.6.25.5-1.1-default ehci_hcd
    usb usb6: SerialNumber: 0000:00:13.5
    PM: Starting manual resume from disk
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda2, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    sd 2:0:0:0: Attached scsi generic sg0 type 0
    sd 3:0:0:0: Attached scsi generic sg1 type 0
    scsi 4:0:0:0: Attached scsi generic sg2 type 5
    r8169 Gigabit Ethernet driver 2.2LK loaded
    ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth0: RTL8168b/8111b at 0xffffc20001074000, 00:1d:92:65:0d:b4, XID 38000000 IRQ 4348
    input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
    Driver 'sr' needs updating - please use bus_type methods
    sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 4:0:0:0: Attached scsi CD-ROM sr0
    ACPI: Power Button (CM) [PWRB]
    ACPI: WMI: Mapper loaded
    piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
    ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f]
    ACPI: Device needs an ACPI driver
    ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 23 (level, low) -> IRQ 23
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8]
    rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k
    ACPI: PCI Interrupt 0000:01:00.1 -> GSI 19 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:01:00.1 to 64
    Adding 2104472k swap on /dev/sda1. Priority:-1 extents:1 across:2104472k
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[00dc1000013cb3c8]
    device-mapper: uevent: version 1.0.3
    device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
    loop: module loaded
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda3, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    fuse init (API version 7.9)
    type=1505 audit(1228125335.564:2): operation="profile_load" name="/bin/ping" name2="default" pid=1596
    type=1505 audit(1228125335.589:3): operation="profile_load" name="/sbin/klogd" name2="default" pid=1612
    type=1505 audit(1228125335.617:4): operation="profile_load" name="/sbin/syslog-ng" name2="default" pid=1616
    type=1505 audit(1228125335.649:5): operation="profile_load" name="/sbin/syslogd" name2="default" pid=1623
    type=1505 audit(1228125335.753:6): operation="profile_load" name="/usr/sbin/avahi-daemon" name2="default" pid=1637
    type=1505 audit(1228125335.777:7): operation="profile_load" name="/usr/sbin/identd" name2="default" pid=1638
    type=1505 audit(1228125335.803:8): operation="profile_load" name="/usr/sbin/mdnsd" name2="default" pid=1639
    type=1505 audit(1228125335.835:9): operation="profile_load" name="/usr/sbin/nscd" name2="default" pid=1640
    type=1505 audit(1228125335.875:10): operation="profile_load" name="/usr/sbin/ntpd" name2="default" pid=1641
    type=1505 audit(1228125335.903:11): operation="profile_load" name="/usr/sbin/traceroute" name2="default" pid=1648
    powernow-k8: Found 1 AMD Phenom(tm) 9500 Quad-Core Processor processors (4 cpu cores) (version 2.20.00)
    powernow-k8: 0 : pstate 0 (2200 MHz)
    powernow-k8: 1 : pstate 1 (1100 MHz)
    r8169: eth0: link up
    r8169: eth0: link up
    NET: Registered protocol family 17
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    bootsplash: status on console 0 changed to on
    eth0: no IPv6 routers present

    ifconfig:
    Bei ifconfig er halte ich die Nachricht file not found.

    Gruss

    Olaf
     
  6. #5 sim4000, 01.12.2008
    sim4000

    sim4000 Lebende Foren Legende

    Dabei seit:
    12.04.2006
    Beiträge:
    1.933
    Zustimmungen:
    0
    Ort:
    In meinem Zimmer
  7. #6 trunksen, 01.12.2008
    trunksen

    trunksen Doppel-As

    Dabei seit:
    13.10.2006
    Beiträge:
    139
    Zustimmungen:
    0
    Ort:
    Österreich, Steiermark
    Hi!

    Einmal allgemein, hast du einen DHCP-Server oder musst du deine IP manuell eingeben?
    Wenn du einen DHCP-Server verwendest, scheint deine NW-Karte nicht konfiguriert zu sein, wenn du statische IP verwendest musst du die wie always-godlike bereits sagte unter Yast > Hardware > Netzwerkkarte einstellen!

    mfg trunksen
     
  8. niLs

    niLs òle òle

    Dabei seit:
    10.06.2004
    Beiträge:
    153
    Zustimmungen:
    0
    Ort:
    Hannover
    Unter welchem Benutzer versuchst du ifconfig auszuführen?
     
  9. #8 Tomekk228, 01.12.2008
    Tomekk228

    Tomekk228 Lebende Foren Legende

    Dabei seit:
    14.08.2007
    Beiträge:
    2.417
    Zustimmungen:
    0
    Ort:
    /home/tomekk/
    lspci wär besser als dmesg :)
     
  10. janis

    janis BOFH

    Dabei seit:
    02.09.2007
    Beiträge:
    179
    Zustimmungen:
    0
    Ort:
    Deutschland
    Wenn ich das richtig interpretiere hast du einen Router oder?
    Dann schaust du unter Yast mal, ob deine Netzwerkkarte erkannt wurde.

    Wenn du ein DSL Modem über USB angeschlossen hast, schaust du bitte mal hier vorbei:
    http://www.unixboard.de/vb3/showthread.php?t=36771#postcount290238
     
  11. #10 Olaf_S, 02.12.2008
    Zuletzt von einem Moderator bearbeitet: 02.12.2008
    Olaf_S

    Olaf_S Guest

    Hi,

    meine Netzwerkkarte wurde erkannt und ich gehe über DSL-Modem ans Netz. Zwischen dem DSL-Modem und der Netzwerkkarte ist ein Switch. Beide sond mit einem LAN-Kabel verbunden.

    Unter XP klappt das prima. Nur von Linux / UNIX habe ich keine tiefere Kenntniss ich bin bisher immer nur als User auf dem System herum gerutscht. D. H. ich kann auf der Konsole arbeiten aber mir fehlen administrative Kenntnisse.

    Gruss

    Olaf
     
  12. janis

    janis BOFH

    Dabei seit:
    02.09.2007
    Beiträge:
    179
    Zustimmungen:
    0
    Ort:
    Deutschland
    OK
    dann gib in XP mal in der Konsole
    Code:
    ipconfig /all>C:\netwerk.txt
    ein.
    Und lade dann bitte die Datei Netzwerk.txt von der C-Platte hoch.
     
  13. #12 Olaf_S, 03.12.2008
    Zuletzt von einem Moderator bearbeitet: 03.12.2008
    Olaf_S

    Olaf_S Guest

    Hi nach einem Wechsel an der Konsole auf su läuft jetzt ifconfig
    Code:
    eth0      Link encap:Ethernet  Hardware Adresse 00:1D:92:65:0D:B4  
              inet Adresse:192.168.0.11  Bcast:192.168.0.255  Maske:255.255.255.0
              inet6 Adresse: fe80::21d:92ff:fe65:db4/64 Gültigkeitsbereich:Verbindung
              UP BROADCAST RUNNING MULTICAST  MTU:1492  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:39 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 Sendewarteschlangenlänge:1000 
              RX bytes:0 (0.0 b)  TX bytes:6508 (6.3 Kb)
              Interrupt:252 Basisadresse:0x2000 
    
    Ich habe nämlich nur Linux auf dem Rechner.
    inet Adresse und Maske habe ich testweise mittles Yast statisch eingegeben. Sie können also nach belieben gelöscht usw. werden.

    Gruss

    Olaf
     
  14. janis

    janis BOFH

    Dabei seit:
    02.09.2007
    Beiträge:
    179
    Zustimmungen:
    0
    Ort:
    Deutschland
    kannst du mal bitte das Ergebnis von Windows XP posten?

    Danke

    Edit:// Muss nicht der Rechner sein, Hauptsache ist, dass er im selben Netzwerk ist (also mit am Switch hängt)
     
  15. Anzeige

    Vielleicht findest du HIER Antworten.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  16. Gast1

    Gast1 Guest

    +

    = http://www.linuxforen.de/forums/showpost.php?p=1572463&postcount=10
     
  17. Olaf_S

    Olaf_S Guest

    Der Artikel über Windows war interessant. Nur ich habe kein Windows auf dem Rechner er läuft ausschießlich mit LINUX und im BIOS habe ich auch keinen hinweis auf "Wake Up On LAN" gefunden.

    Ich kann den Linux-Rechner von Windows-Rechner aus mit einem Ping erreichen aber vom Linux Rechner geht kein Ping zum Windows-Rechner. Ergo scheint das Problem bei der Linux-Konfiguration zu sein. Weiter bin ich mit meinem Wissen noch nicht.

    Zur weiteren Info ich habe zwei Rechner. Einen auf dem ausschließlich Linux und einen auf dem ausschließlich Windows läuft. Mein Ziel ist es, den Windows-Rechner eines schönen Tages zu verschrotten.

    Gruss

    Olaf
     
Thema:

komme mit openSuse 11 nicht ins Internet

Die Seite wird geladen...

komme mit openSuse 11 nicht ins Internet - Ähnliche Themen

  1. OpenSuse - komme mir xine/wine/grafik und anderen nicht weiter

    OpenSuse - komme mir xine/wine/grafik und anderen nicht weiter: hallo, erstmal soviel...ich bin sehr unerfahren mit opensuse und anderen unixsystemen. hatte ubuntu ausprobiert und wollte/will linux zum laufen...
  2. libstdc++-libc6.2-2.so.3 - wo bekomme ich ein RPM ? OpenSuSE 10.1

    libstdc++-libc6.2-2.so.3 - wo bekomme ich ein RPM ? OpenSuSE 10.1: Hallo Zusammen, wo bekomme ich denn ein RPM in dem die "libstdc++-libc6.2-2.so.3" fuer OpenSuSe 10.1 ? Danke ds2k5
  3. Wie komme ich an den Inhalt des Inhalts einer Variable?

    Wie komme ich an den Inhalt des Inhalts einer Variable?: Hallo Zusammen, ich möchte meine Buildumgebung vereinfachen und besser zu automatisieren. Ein Skript schreibt Pfade in die env und diese...
  4. Dronecode-Projekt bringt kommerzielle Drohnenanwendungen voran

    Dronecode-Projekt bringt kommerzielle Drohnenanwendungen voran: Das vor über einem Jahr gegründete Dronecode-Projekt zählt jetzt 51 Mitglieder und und verstärkt seine Bemühungen um eine einheitliche Plattform...
  5. Android 6.0 ab kommender Woche verfügbar

    Android 6.0 ab kommender Woche verfügbar: Google hat die Freigabe der kommenden Android-Version 6.0 »Marshmallow« für die kommende Woche angekündigt. Zu den Geräten, die die Aktualisierung...