IBM T22, Debian Etch 4, X-server start nach Neuinstall

Dieses Thema im Forum "Installation & Basiskonfiguration" wurde erstellt von uwe_911, 16.04.2007.

  1. #1 uwe_911, 16.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    IBM T22, Debian Etch 4, X-Server Start
    Hallo Linuxer,
    ich habe da ein seltsames Problem mit meinem T22.
    Debian Etch habe ich frisch installiert. Der T22 ist am Netzteil angeschlossen. Nach der Installation kommt der Re-Start und das Gerät bleibt beim starten des X-Servers mit -Cursor Oben Links Auf Dem Bildschirm- stehen. Es reagiert auf keine Tastatureingabe mehr.
    Also schalte ich durch den Netzschalter aus. Starte neu, dieses mal mit Akku Power und siehe da, der X Server startet. Solange das Gerät mit Akku betrieben wird kann man dieses Spiel endlos wiederholen doch wehe man versucht's mit Netzbetrieb.
    Hatte dieses Phänomen auch schon unter Debian Etch Testing.
    Ein Tipp in einem Forum war die Section DRI raus zu nehmen, hab ich jetzt auch versucht --> kein Erfolg.
    Hier sind mal die Infos die ich zu diesem Thema gesammelt habe :
    =======================================================
    Module Size Used by
    rfcomm 34584 0
    l2cap 21696 5 rfcomm
    bluetooth 45956 4 rfcomm,l2cap
    savage 28448 2
    drm 61332 3 savage
    nfs 202828 0
    nfsd 197936 17
    exportfs 5600 1 nfsd
    lockd 54344 3 nfs,nfsd
    nfs_acl 3584 2 nfs,nfsd
    sunrpc 138812 13 nfs,nfsd,lockd,nfs_acl
    nvram 8328 1
    uinput 8288 1
    ppdev 8676 0
    lp 11012 0
    button 6672 0
    ac 5188 0
    battery 9636 0
    ipv6 226016 12
    dm_snapshot 15552 0
    dm_mirror 19152 0
    dm_mod 50232 2 dm_snapshot,dm_mirror
    loop 15048 0
    serial_cs 18116 1
    irtty_sir 7808 0
    sir_dev 15492 1 irtty_sir
    tsdev 7520 0
    snd_cs46xx 76360 2
    gameport 14632 2 snd_cs46xx
    snd_seq_dummy 3844 0
    snd_seq_oss 28768 0
    xircom_cb 10272 0
    nsc_ircc 20912 0
    snd_seq_midi 8192 0
    irda 162588 3 irtty_sir,sir_dev,nsc_ircc
    pcmcia 34140 1 serial_cs
    firmware_class 9600 1 pcmcia
    snd_seq_midi_event 7008 2 snd_seq_oss,snd_seq_midi
    crc_ccitt 2240 1 irda
    parport_pc 32132 1
    parport 33256 3 ppdev,lp,parport_pc
    snd_seq 45680 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
    floppy 53156 0
    snd_rawmidi 22560 2 snd_cs46xx,snd_seq_midi
    snd_seq_device 7820 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
    snd_ac97_codec 83104 1 snd_cs46xx
    snd_ac97_bus 2400 1 snd_ac97_codec
    rtc 12372 0
    psmouse 35016 0
    snd_pcm_oss 38368 1
    snd_mixer_oss 15200 1 snd_pcm_oss
    serio_raw 6660 0
    i2c_piix4 8140 0
    snd_pcm 68676 3 snd_cs46xx,snd_ac97_codec,snd_pcm_oss
    snd_timer 20996 2 snd_seq,snd_pcm
    snd 47012 12 snd_cs46xx,snd_seq_oss,snd_seq,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
    soundcore 9248 2 snd
    snd_page_alloc 9640 2 snd_cs46xx,snd_pcm
    pcspkr 3072 0
    i2c_core 19680 1 i2c_piix4
    intel_agp 21148 1
    agpgart 29896 2 drm,intel_agp
    yenta_socket 24460 5
    rsrc_nonstatic 11840 1 yenta_socket
    pcmcia_core 36852 4 serial_cs,pcmcia,yenta_socket,rsrc_nonstatic
    shpchp 33024 0
    pci_hotplug 28704 1 shpchp
    evdev 9088 2
    ext3 119240 2
    jbd 52456 1 ext3
    mbcache 8356 1 ext3
    ide_disk 14848 4
    ide_cd 36064 0
    cdrom 32544 1 ide_cd
    uhci_hcd 21164 0
    usbcore 112644 2 uhci_hcd
    piix 9444 0 [permanent]
    generic 5476 0 [permanent]
    ide_core 110504 4 ide_disk,ide_cd,piix,generic
    e100 32232 0
    mii 5344 1 e100
    thermal 13608 0
    processor 28840 1 thermal
    fan 4804 0
    Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 17:17:36 UTC 2007
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000000bfe0000 (usable)
    BIOS-e820: 000000000bfe0000 - 000000000bfeec00 (ACPI data)
    BIOS-e820: 000000000bfeec00 - 000000000bff0000 (ACPI NVS)
    BIOS-e820: 000000000bff0000 - 000000000bff4000 (reserved)
    BIOS-e820: 000000000bff4000 - 000000000c000000 (usable)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    192MB LOWMEM available.
    On node 0 totalpages: 49152
    DMA zone: 4096 pages, LIFO batch:0
    Normal zone: 45056 pages, LIFO batch:15
    DMI 2.3 present.
    ACPI: RSDP (v000 PTLTD ) @ 0x000f6eb0
    ACPI: RSDT (v001 PTLTD RSDT 0x06041120 LTP 0x00000000) @ 0x0bfe4b71
    ACPI: FADT (v001 IBM TP-16 0x06041120 0x00000000) @ 0x0bfeeb65
    ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06041120 LTP 0x00000001) @ 0x0bfeebd9
    ACPI: DSDT (v001 IBM TP-16 0x06041120 MSFT 0x0100000c) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x1008
    Allocating PCI resources starting at 10000000 (gap: 0c000000:f3f80000)
    Detected 896.117 MHz processor.
    Built 1 zonelists. Total pages: 49152
    Kernel command line: root=/dev/hda1 ro vga=791
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    mapped APIC to ffffd000 (01189000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 1024 (order: 10, 4096 bytes)
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 186800k/196608k available (1544k kernel code, 9204k reserved, 577k data, 196k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 1793.48 BogoMIPS (lpj=3586962)
    Security Framework v1.0.0 initialized
    SELinux: Disabled at boot.
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
    CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Compat vDSO mapped to ffffe000.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 16k freed
    ACPI: Core revision 20060707
    ACPI: setting ELCR to 0200 (from 0800)
    CPU0: Intel Pentium III (Coppermine) stepping 0a
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    Brought up 1 CPUs
    migration_cost=0
    checking if image is initramfs... it is
    Freeing initrd memory: 4783k freed
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
    PCI quirk: region 1000-103f claimed by PIIX4 ACPI
    PCI quirk: region 1040-104f claimed by PIIX4 SMB
    PIIX4 devres C PIO at 15e8-15ef
    PIIX4 devres I PIO at 03f0-03f7
    PIIX4 devres J PIO at 002e-002f
    Boot video device is 0000:01:00.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: Power Resource [PSER] (off)
    ACPI: Power Resource [PSIO] (on)
    ACPI: Embedded Controller [EC] (gpe 9) interrupt mode.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 15 devices
    PnPBIOS: Disabled by ACPI PNP
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    pnp: 00:02: ioport range 0x1000-0x103f could not be reserved
    pnp: 00:02: ioport range 0x1040-0x104f has been reserved
    pnp: 00:02: ioport range 0xfe00-0xfe0f has been reserved
    pnp: 00:09: ioport range 0x15e0-0x15ef has been reserved
    PCI: Bridge: 0000:00:01.0
    IO window: disabled.
    MEM window: f0000000-f7ffffff
    PREFETCH window: 18000000-180fffff
    PCI: Bus 2, cardbus bridge: 0000:00:02.0
    IO window: 00001400-000014ff
    IO window: 00001c00-00001cff
    PREFETCH window: 10000000-11ffffff
    MEM window: 12000000-13ffffff
    PCI: Bus 6, cardbus bridge: 0000:00:02.1
    IO window: 00002000-000020ff
    IO window: 00002400-000024ff
    PREFETCH window: 14000000-15ffffff
    MEM window: 16000000-17ffffff
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
    ACPI: PCI Interrupt 0000:00:02.1 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 4096)
    TCP reno registered
    Simple Boot Flag at 0x35 set to 0x1
    audit: initializing netlink socket (disabled)
    audit(1176747574.196:1): initialized
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    Limiting direct PCI/PCI transfers.
    vesafb: framebuffer at 0xf0000000, mapped to 0xcc880000, using 3072k, total 8192k
    vesafb: mode is 1024x768x16, linelength=2048, pages=4
    vesafb: protected mode interface info at c000:882d
    vesafb: pmi: set display start = c00c888d, set palette = c00c88d6
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    pnp: Device 00:0c activated.
    00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
    RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    mice: PS/2 mouse device common for all mice
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    NET: Registered protocol family 8
    NET: Registered protocol family 20
    Using IPI No-Shortcut mode
    Time: tsc clocksource has been installed.
    ACPI: (supports S0 S1 S3 S4 S5)
    Freeing unused kernel memory: 196k freed
    input: AT Translated Set 2 keyboard as /class/input/input0
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: Processor [CPU] (supports 8 throttling states)
    ACPI: Thermal Zone [THM0] (58 C)
    e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
    e100: Copyright(c) 1999-2005 Intel Corporation
    ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
    e100: eth0: e100_probe: addr 0xe8120000, irq 11, MAC addr 00:03:47:8A:14:34
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    PIIX4: IDE controller at PCI slot 0000:00:07.1
    PIIX4: chipset revision 1
    PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio
    Probing IDE interface ide0...
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    USB Universal Host Controller Interface driver v3.0
    hda: IC25N040ATCS04-0, ATA DISK drive
    Time: acpi_pm clocksource has been installed.
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: MATSHITADVD-ROM SR-8174, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 11, io base 0x00001860
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    hda: max request size: 128KiB
    hda: 78140160 sectors (40007 MB) w/1768KiB Cache, CHS=65535/16/63, UDMA(33)
    hda: cache flushes not supported
    hda: hda1 hda2 < hda5 hda6 >
    Attempting manual resume
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x04b8, PCI irq 11
    Socket status: 30000020
    Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
    spurious 8259A interrupt: IRQ7.
    Linux agpgart interface v0.101 (c) Dave Jones
    Yenta: ISA IRQ mask 0x04b8, PCI irq 11
    Socket status: 30000010
    agpgart: Detected an Intel 440BX Chipset.
    agpgart: AGP aperture is 64M @ 0xf8000000
    input: PC Speaker as /class/input/input1
    pccard: CardBus card inserted into slot 0
    piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
    piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
    piix4_smbus: probe of 0000:00:07.3 failed with error -1
    Real Time Clock Driver v1.12ac
    pccard: PCMCIA card inserted into slot 1
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a National Semiconductor PC87306
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
    irda_init()
    NET: Registered protocol family 23
    PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth1: Xircom cardbus revision 3 at irq 11
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    input: TPPS/2 IBM TrackPoint as /class/input/input2
    pnp: Device 00:0e activated.
    nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    IrDA: Registered device irda0
    nsc-ircc, Found dongle: Reserved
    nsc_ircc_init_dongle_interface(), Reserved not defined by irda yet
    cs46xx: failure waiting for FIFO command to complete
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    ts: Compaq touchscreen protocol output
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: memory probe 0xa0000000-0xa0ffffff: clean.
    pcmcia: registering new device pcmcia1.0
    gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1807kHz
    1.0: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
    Adding 562232k swap on /dev/hda5. Priority:-1 extents:1 across:562232k
    EXT3 FS on hda1, internal journal
    loop: loaded (max 8 devices)
    device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda6, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
    pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
    pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
    cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
    cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
    cs: warning: no high memory space available!
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ACPI: Battery Slot [BAT0] (battery present)
    ACPI: AC Adapter [AC] (on-line)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Lid Switch [LID]
    ACPI: Sleep Button (CM) [SLPB]
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    xircom cardbus adaptor found, registering as eth1, using irq 11
    Non-volatile memory driver v1.2
    input: /usr/sbin/thinkpad-keys as /class/input/input3
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    NFSD: starting 90-second grace period
    [drm] Initialized drm 1.0.1 20051102
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized savage 2.4.1 20050313 on minor 0
    mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
    agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
    agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
    agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
    Bluetooth: Core ver 2.10
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP ver 2.8
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: RFCOMM socket layer initialized
    Bluetooth: RFCOMM TTY layer initialized
    Bluetooth: RFCOMM ver 1.8
    eth0: no IPv6 routers present
    ========================================================================

    # /etc/X11/xorg.conf (xorg X Window System server configuration file)
    #
    # This file was generated by dexconf, the Debian X Configuration tool, using
    # values from the debconf database.
    #
    # Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
    # (Type "man /etc/X11/xorg.conf" at the shell prompt.)
    #
    # This file is automatically updated on xserver-xorg package upgrades *only*
    # if it has not been modified since the last upgrade of the xserver-xorg
    # package.
    #
    # If you have edited this file but would like it to be automatically updated
    # again, run the following command:
    # sudo dpkg-reconfigure -phigh xserver-xorg

    Section "Files"
    FontPath "/usr/share/fonts/X11/misc"
    FontPath "/usr/X11R6/lib/X11/fonts/misc"
    FontPath "/usr/share/fonts/X11/cyrillic"
    FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
    FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
    FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
    FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
    FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
    FontPath "/usr/share/fonts/X11/Type1"
    FontPath "/usr/X11R6/lib/X11/fonts/Type1"
    FontPath "/usr/share/fonts/X11/100dpi"
    FontPath "/usr/X11R6/lib/X11/fonts/100dpi"
    FontPath "/usr/share/fonts/X11/75dpi"
    FontPath "/usr/X11R6/lib/X11/fonts/75dpi"
    # path to defoma fonts
    FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
    EndSection

    Section "Module"
    Load "i2c"
    Load "bitmap"
    Load "ddc"
    Load "dri"
    Load "extmod"
    Load "freetype"
    Load "glx"
    Load "int10"
    Load "vbe"
    EndSection

    Section "InputDevice"
    Identifier "Generic Keyboard"
    Driver "kbd"
    Option "CoreKeyboard"
    Option "XkbRules" "xorg"
    Option "XkbModel" "pc105"
    Option "XkbLayout" "de"
    Option "XkbVariant" "nodeadkeys"
    EndSection

    Section "InputDevice"
    Identifier "Configured Mouse"
    Driver "mouse"
    Option "CorePointer"
    Option "Device" "/dev/input/mice"
    Option "Protocol" "ImPS/2"
    Option "Emulate3Buttons" "true"
    EndSection

    Section "InputDevice"
    Identifier "Synaptics Touchpad"
    Driver "synaptics"
    Option "SendCoreEvents" "true"
    Option "Device" "/dev/psaux"
    Option "Protocol" "auto-dev"
    Option "HorizScrollDelta" "0"
    EndSection

    Section "Device"
    Identifier "S3 Inc. 86C270-294 Savage/IX-MV"
    Driver "savage"
    BusID "PCI:1:0:0"
    EndSection

    Section "Monitor"
    Identifier "Standardbildschirm"
    Option "DPMS"
    HorizSync 28-51
    VertRefresh 43-60
    EndSection

    Section "Screen"
    Identifier "Default Screen"
    Device "S3 Inc. 86C270-294 Savage/IX-MV"
    Monitor "Standardbildschirm"
    DefaultDepth 16
    SubSection "Display"
    Depth 1
    Modes "1024x768"
    EndSubSection
    SubSection "Display"
    Depth 4
    Modes "1024x768"
    EndSubSection
    SubSection "Display"
    Depth 8
    Modes "1024x768"
    EndSubSection
    SubSection "Display"
    Depth 15
    Modes "1024x768"
    EndSubSection
    SubSection "Display"
    Depth 16
    Modes "1024x768"
    EndSubSection
    SubSection "Display"
    Depth 24
    Modes "1024x768"
    EndSubSection
    EndSection

    Section "ServerLayout"
    Identifier "Default Layout"
    Screen "Default Screen"
    InputDevice "Generic Keyboard"
    InputDevice "Configured Mouse"
    InputDevice "Synaptics Touchpad"
    EndSection

    #Section "DRI"
    # Mode 0666
    #EndSection

    ==================================================================================

    X Window System Version 7.1.1
    Release Date: 12 May 2006
    X Protocol Version 11, Revision 0, Release 7.1.1
    Build Operating System: UNKNOWN
    Current Operating System: Linux Mobilix 2.6.18-4-686 #1 SMP Mon Mar 26 17:17:36 UTC 2007 i686
    Build Date: 04 April 2007
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    Module Loader present
    Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    (==) Log file: "/var/log/Xorg.0.log", Time: Mon Apr 16 19:55:21 2007
    (==) Using config file: "/etc/X11/xorg.conf"
    (==) ServerLayout "Default Layout"
    (**) |-->Screen "Default Screen" (0)
    (**) | |-->Monitor "Standardbildschirm"
    (**) | |-->Device "S3 Inc. 86C270-294 Savage/IX-MV"
    (**) |-->Input Device "Generic Keyboard"
    (**) |-->Input Device "Configured Mouse"
    (**) |-->Input Device "Synaptics Touchpad"
    (WW) The directory "/usr/X11R6/lib/X11/fonts/misc" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/cyrillic" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/100dpi/" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/75dpi/" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/Type1" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist.
    Entry deleted from font path.
    (WW) The directory "/usr/X11R6/lib/X11/fonts/75dpi" does not exist.
    Entry deleted from font path.
    (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
    Entry deleted from font path.
    (**) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi
    (==) RgbPath set to "/etc/X11/rgb"
    (==) ModulePath set to "/usr/lib/xorg/modules"
    (II) Open ACPI successful (/var/run/acpid.socket)
    (II) Module ABI versions:
    X.Org ANSI C Emulation: 0.3
    X.Org Video Driver: 1.0
    X.Org XInput driver : 0.6
    X.Org Server Extension : 0.3
    X.Org Font Renderer : 0.5
    (II) Loader running on linux
    (II) LoadModule: "bitmap"
    (II) Loading /usr/lib/xorg/modules/fonts/libbitmap.so
    (II) Module bitmap: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
    (II) Loading font Bitmap
    (II) LoadModule: "pcidata"
    (II) Loading /usr/lib/xorg/modules/libpcidata.so
    (II) Module pcidata: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Video Driver, version 1.0
    (++) using VT number 7

    (II) PCI: PCI scan (all values are in hex)
    (II) PCI: 00:00:0: chip 8086,7190 card 0000,0000 rev 03 class 06,00,00 hdr 00
    (II) PCI: 00:01:0: chip 8086,7191 card 0000,0000 rev 03 class 06,04,00 hdr 01
    (II) PCI: 00:02:0: chip 104c,ac1b card 1400,0000 rev 03 class 06,07,00 hdr 82
    (II) PCI: 00:02:1: chip 104c,ac1b card 2000,0000 rev 03 class 06,07,00 hdr 82
    (II) PCI: 00:03:0: chip 8086,1229 card 8086,2205 rev 0c class 02,00,00 hdr 80
    (II) PCI: 00:03:1: chip 11c1,045c card 8086,2205 rev 01 class 07,00,00 hdr 80
    (II) PCI: 00:05:0: chip 1013,6003 card 1014,0153 rev 01 class 04,01,00 hdr 00
    (II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 02 class 06,80,00 hdr 80
    (II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00
    (II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00
    (II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 03 class 06,80,00 hdr 00
    (II) PCI: 01:00:0: chip 5333,8c12 card 1014,017f rev 13 class 03,00,00 hdr 00
    (II) PCI: 02:00:0: chip 115d,0003 card 1014,8181 rev 03 class 02,00,00 hdr 00
    (II) PCI: End of PCI scan
    (II) Host-to-PCI bridge:
    (II) Bus 0: bridge is at (0:0:0), (0,0,6), BCTRL: 0x0008 (VGA_EN is set)
    (II) Bus 0 I/O range:
    [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX
    (II) Bus 0 non-prefetchable memory range:
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX
    (II) Bus 0 prefetchable memory range:
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX
    (II) PCI-to-PCI bridge:
    (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x008c (VGA_EN is set)
    (II) Bus 1 non-prefetchable memory range:
    [0] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX
    (II) Bus 1 prefetchable memory range:
    [0] -1 0 0x18000000 - 0x180fffff (0x100000) MX
    (II) PCI-to-CardBus bridge:
    (II) Bus 2: bridge is at (0:2:0), (0,2,5), BCTRL: 0x0500 (VGA_EN is cleared)
    (II) Bus 2 I/O range:
    [0] -1 0 0x00001400 - 0x000014ff (0x100) IX
    [1] -1 0 0x00001c00 - 0x00001cff (0x100) IX
    (II) Bus 2 non-prefetchable memory range:
    [0] -1 0 0x12000000 - 0x13ffffff (0x2000000) MX
    (II) Bus 2 prefetchable memory range:
    [0] -1 0 0x10000000 - 0x11ffffff (0x2000000) MX
    (II) PCI-to-CardBus bridge:
    (II) Bus 6: bridge is at (0:2:1), (0,6,9), BCTRL: 0x05c0 (VGA_EN is cleared)
    (II) Bus 6 I/O range:
    [0] -1 0 0x00002000 - 0x000020ff (0x100) IX
    [1] -1 0 0x00002400 - 0x000024ff (0x100) IX
    (II) Bus 6 non-prefetchable memory range:
    [0] -1 0 0x16000000 - 0x17ffffff (0x2000000) MX
    (II) Bus 6 prefetchable memory range:
    [0] -1 0 0x14000000 - 0x15ffffff (0x2000000) MX
    (--) PCI:*(1:0:0) S3 Inc. 86C270-294 Savage/IX-MV rev 19, Mem @ 0xf0000000/27
    (II) Addressable bus resource ranges are
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX
    [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX
    (II) OS-reported resource ranges:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX
    [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    (II) PCI Memory resource overlap reduced 0xf8000000 from 0xfbffffff to 0xf7ffffff
    (II) Active PCI resource ranges:
    [0] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [1] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [2] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [3] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [4] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [5] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [6] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [7] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [8] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [9] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [10] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [11] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [12] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [13] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    (II) Active PCI resource ranges after removing overlaps:
    [0] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [1] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [2] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [3] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [4] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [5] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [6] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [7] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [8] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [9] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [10] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [11] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [12] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [13] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    (II) OS-reported resource ranges after removing overlaps with PCI:
    [0] -1 0 0x00100000 - 0x11ffffff (0x11f00000) MX[B]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    (II) All system resource ranges:
    [0] -1 0 0x00100000 - 0x11ffffff (0x11f00000) MX[B]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [4] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [5] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [6] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [7] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [8] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [9] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [10] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [11] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [12] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    [15] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [16] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [17] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [18] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [19] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    (II) LoadModule: "i2c"
    (II) Loading /usr/lib/xorg/modules/libi2c.so
    (II) Module i2c: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.2.0
    ABI class: X.Org Video Driver, version 1.0
    (II) LoadModule: "bitmap"
    (II) Reloading /usr/lib/xorg/modules/fonts/libbitmap.so
    (II) Loading font Bitmap
    (II) LoadModule: "ddc"
    (II) Loading /usr/lib/xorg/modules/libddc.so
    (II) Module ddc: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Video Driver, version 1.0
    (II) LoadModule: "dri"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    (II) Module dri: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading sub module "drm"
    (II) LoadModule: "drm"
    (II) Loading /usr/lib/xorg/modules/linux/libdrm.so
    (II) Module drm: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension XFree86-DRI
    (II) LoadModule: "extmod"
    (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    (II) Module extmod: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension SHAPE
    (II) Loading extension MIT-SUNDRY-NONSTANDARD
    (II) Loading extension BIG-REQUESTS
    (II) Loading extension SYNC
    (II) Loading extension MIT-SCREEN-SAVER
    (II) Loading extension XC-MISC
    (II) Loading extension XFree86-VidModeExtension
    (II) Loading extension XFree86-Misc
    (II) Loading extension XFree86-DGA
    (II) Loading extension DPMS
    (II) Loading extension TOG-CUP
    (II) Loading extension Extended-Visual-Information
    (II) Loading extension XVideo
    (II) Loading extension XVideo-MotionCompensation
    (II) Loading extension X-Resource
    (II) LoadModule: "freetype"
    (II) Loading /usr/lib/xorg/modules/fonts/libfreetype.so
    (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
    compiled for 7.1.1, module version = 2.1.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
    (II) Loading font FreeType
    (II) LoadModule: "glx"
    (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    (II) Module glx: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (==) AIGLX enabled
    (II) Loading extension GLX
    (II) LoadModule: "int10"
    (II) Loading /usr/lib/xorg/modules/libint10.so
    (II) Module int10: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Video Driver, version 1.0
    (II) LoadModule: "vbe"
    (II) Loading /usr/lib/xorg/modules/libvbe.so
    (II) Module vbe: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.1.0
    ABI class: X.Org Video Driver, version 1.0
    (II) LoadModule: "savage"
    (II) Loading /usr/lib/xorg/modules/drivers/savage_drv.so
    (II) Module savage: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 2.1.2
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 1.0
    (II) LoadModule: "kbd"
    (II) Loading /usr/lib/xorg/modules/input/kbd_drv.so
    (II) Module kbd: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.1.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 0.6
    (II) LoadModule: "mouse"
    (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
    (II) Module mouse: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.1.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 0.6
    (II) LoadModule: "synaptics"
    (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
    (II) Module synaptics: vendor="The XFree86 Project"
    compiled for 4.2.0, module version = 1.0.0
    Module class: XFree86 XInput Driver
    ABI class: XFree86 XInput driver, version 0.3
    (II) SAVAGE: driver (version 2.1.2) for S3 Savage chipsets: Savage4,
    Savage3D, Savage3D-MV, Savage2000, Savage/MX-MV, Savage/MX,
    Savage/IX-MV, Savage/IX, ProSavage PM133, ProSavage KM133,
    Twister PN133, Twister KN133, SuperSavage/MX 128, SuperSavage/MX 64,
    SuperSavage/MX 64C, SuperSavage/IX 128, SuperSavage/IX 128,
    SuperSavage/IX 64, SuperSavage/IX 64, SuperSavage/IXC 64,
    SuperSavage/IXC 64, ProSavage DDR, ProSavage DDR-K
    (II) Primary Device is: PCI 01:00:0
    (--) Chipset MobileSavage found
    (II) resource ranges after xf86ClaimFixedResources() call:
    [0] -1 0 0x00100000 - 0x11ffffff (0x11f00000) MX[B]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [4] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [5] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [6] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [7] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [8] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [9] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [10] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [11] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [12] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    [15] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [16] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [17] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [18] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [19] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    (II) resource ranges after probing:
    [0] -1 0 0x00100000 - 0x11ffffff (0x11f00000) MX[B]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [4] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [5] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [6] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [7] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [8] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [9] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [10] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [11] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [12] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
    [14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
    [15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
    [16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    [18] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [19] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [20] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [21] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [22] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    [23] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
    [24] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
    (II) Setting vga for screen 0.
    (II) Loading sub module "vgahw"
    (II) LoadModule: "vgahw"
    (II) Loading /usr/lib/xorg/modules/libvgahw.so
    (II) Module vgahw: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 0.1.0
    ABI class: X.Org Video Driver, version 1.0
    (**) SAVAGE(0): Depth 16, (--) framebuffer bpp 16
    (==) SAVAGE(0): RGB weight 565
    (==) SAVAGE(0): Default visual is TrueColor
    (II) SAVAGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
    (==) SAVAGE(0): Using XAA acceleration architecture
    (==) SAVAGE(0): Using HW cursor
    (==) SAVAGE(0): Using video BIOS to set modes
    (II) Loading sub module "vbe"
    (II) LoadModule: "vbe"
    (II) Reloading /usr/lib/xorg/modules/libvbe.so
    (II) Loading sub module "int10"
    (II) LoadModule: "int10"
    (II) Reloading /usr/lib/xorg/modules/libint10.so
    (II) SAVAGE(0): initializing int10
    (II) Loading sub module "vm86"
    (II) LoadModule: "vm86"
    (II) Loading /usr/lib/xorg/modules/libvm86.so
    (II) Module vm86: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Video Driver, version 1.0
    (II) SAVAGE(0): Primary V_BIOS segment is: 0xc000
    (II) SAVAGE(0): VESA BIOS detected
    (II) SAVAGE(0): VESA VBE Version 2.0
    (II) SAVAGE(0): VESA VBE Total Mem: 8192 kB
    (II) SAVAGE(0): VESA VBE OEM: S3 Incorporated. M7 BIOS
    (II) SAVAGE(0): VESA VBE OEM Software Rev: 1.0
    (II) SAVAGE(0): VESA VBE OEM Vendor: S3 Incorporated.
    (II) SAVAGE(0): VESA VBE OEM Product: VBE 2.0
    (II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 1.1
    (--) SAVAGE(0): Chip: id 8c12, "Savage/IX-MV"
    (--) SAVAGE(0): Engine: "MobileSavage"
    (--) SAVAGE(0): AGP card detected
    (==) SAVAGE(0): Using AGP DMA
    (II) SAVAGE(0): Savage3D/MX/IX does not support command DMA.
    (==) SAVAGE(0): Will try only vertex DMA mode
    (==) SAVAGE(0): Using AGP 1x mode
    (==) SAVAGE(0): Using 16 MB AGP aperture
    (==) SAVAGE(0): Using gamma correction (1.0, 1.0, 1.0)
    (--) SAVAGE(0): probed videoram: 8192k
    (II) Loading sub module "ddc"
    (II) LoadModule: "ddc"
    (II) Reloading /usr/lib/xorg/modules/libddc.so
    (--) SAVAGE(0): No DDC signal
    (II) Loading sub module "i2c"
    (II) LoadModule: "i2c"
    (II) Reloading /usr/lib/xorg/modules/libi2c.so
    (II) SAVAGE(0): I2C bus "I2C bus" initialized.
    (II) SAVAGE(0): I2C device "I2C bus:ddc2" registered at address 0xA0.
    (II) SAVAGE(0): I2C device "I2C bus:ddc2" removed.
    (--) SAVAGE(0): Detected current MCLK value of 120.511 MHz
    (--) SAVAGE(0): 1024x768 TFT LCD panel detected and active
    (--) SAVAGE(0): - Limiting video mode to 1024x768
    (--) SAVAGE(0): Found 13 modes at this depth:
    [10e] 320 x 200, 70Hz
    [111] 640 x 480, 60Hz, 72Hz, 75Hz, 85Hz, 100Hz
    [114] 800 x 600, 60Hz, 72Hz, 75Hz, 85Hz, 100Hz
    [117] 1024 x 768, 60Hz, 70Hz, 75Hz, 85Hz, 43Hz, 100Hz
    [11a] 1280 x 1024, 60Hz, 75Hz, 85Hz, 43Hz
    [11d] 640 x 400, 70Hz
    [122] 1600 x 1200, 48Hz, 60Hz, 75Hz, 85Hz
    [133] 320 x 240, 72Hz
    [13c] 1400 x 1050, 60Hz, 75Hz
    [143] 400 x 300, 72Hz
    [153] 512 x 384, 70Hz
    [173] 720 x 480, 75Hz
    [178] 720 x 576, 75Hz
    (II) SAVAGE(0): Standardbildschirm: Using hsync range of 28.00-51.00 kHz
    (II) SAVAGE(0): Standardbildschirm: Using vrefresh range of 43.00-60.00 Hz
    (II) SAVAGE(0): Clock range: 10.00 to 250.00 MHz
    (--) SAVAGE(0): No suitable BIOS mode found for 640x350 85Hz.
    (II) SAVAGE(0): Not using default mode "640x350" (no mode of this name)
    (--) SAVAGE(0): No suitable BIOS mode found for 320x175 85Hz.
    (II) SAVAGE(0): Not using default mode "320x175" (no mode of this name)
    (--) SAVAGE(0): Chose mode 11d at 70Hz.
    (II) SAVAGE(0): Not using default mode "640x400" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 10e at 70Hz.
    (II) SAVAGE(0): Not using default mode "320x200" (vrefresh out of range)
    (--) SAVAGE(0): No suitable BIOS mode found for 720x400 85Hz.
    (II) SAVAGE(0): Not using default mode "720x400" (no mode of this name)
    (--) SAVAGE(0): No suitable BIOS mode found for 360x200 85Hz.
    (II) SAVAGE(0): Not using default mode "360x200" (no mode of this name)
    (--) SAVAGE(0): Chose mode 111 at 60Hz.
    (--) SAVAGE(0): Chose mode 133 at 72Hz.
    (--) SAVAGE(0): Chose mode 111 at 72Hz.
    (II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 133 at 72Hz.
    (II) SAVAGE(0): Not using default mode "320x240" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 111 at 75Hz.
    (II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 133 at 72Hz.
    (II) SAVAGE(0): Not using default mode "320x240" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 111 at 85Hz.
    (II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 133 at 72Hz.
    (II) SAVAGE(0): Not using default mode "320x240" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (--) SAVAGE(0): Chose mode 114 at 72Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (II) SAVAGE(0): Not using default mode "400x300" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 114 at 75Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (II) SAVAGE(0): Not using default mode "400x300" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 114 at 85Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (II) SAVAGE(0): Not using default mode "400x300" (hsync out of range)
    (--) SAVAGE(0): Chose mode 117 at 85Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (II) SAVAGE(0): Not using default mode "512x384" (vrefresh out of range)
    (--) SAVAGE(0): Chose mode 117 at 60Hz.
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (--) SAVAGE(0): Chose mode 117 at 70Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (II) SAVAGE(0): Not using default mode "512x384" (hsync out of range)
    (--) SAVAGE(0): Chose mode 117 at 75Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (II) SAVAGE(0): Not using default mode "512x384" (hsync out of range)
    (--) SAVAGE(0): Chose mode 117 at 85Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (II) SAVAGE(0): Not using default mode "512x384" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1152x864" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 576x432 75Hz.
    (II) SAVAGE(0): Not using default mode "576x432" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1280x960" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 111 at 60Hz.
    (II) SAVAGE(0): Not using default mode "640x480" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1280x960" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 111 at 85Hz.
    (II) SAVAGE(0): Not using default mode "640x480" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 640x512 60Hz.
    (II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 640x512 75Hz.
    (II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 640x512 85Hz.
    (II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 114 at 72Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 114 at 75Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 114 at 85Hz.
    (II) SAVAGE(0): Not using default mode "800x600" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "1792x1344" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 896x672 60Hz.
    (II) SAVAGE(0): Not using default mode "896x672" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): No suitable BIOS mode found for 896x672 75Hz.
    (II) SAVAGE(0): Not using default mode "896x672" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1856x1392" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 928x696 60Hz.
    (II) SAVAGE(0): Not using default mode "928x696" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): No suitable BIOS mode found for 928x696 75Hz.
    (II) SAVAGE(0): Not using default mode "928x696" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1920x1440" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 960x720 60Hz.
    (II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): No suitable BIOS mode found for 960x720 75Hz.
    (II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
    (--) SAVAGE(0): No suitable BIOS mode found for 832x624 74Hz.
    (II) SAVAGE(0): Not using default mode "832x624" (no mode of this name)
    (--) SAVAGE(0): No suitable BIOS mode found for 416x312 74Hz.
    (II) SAVAGE(0): Not using default mode "416x312" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1280x768" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 640x384 60Hz.
    (II) SAVAGE(0): Not using default mode "640x384" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1280x800" (exceeds panel dimensions)
    (--) SAVAGE(0): Chose mode 11d at 70Hz.
    (II) SAVAGE(0): Not using default mode "1152x768" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 576x384 54Hz.
    (II) SAVAGE(0): Not using default mode "576x384" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1152x864" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 576x432 85Hz.
    (II) SAVAGE(0): Not using default mode "576x432" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 700x525 59Hz.
    (II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 700x525 70Hz.
    (II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 700x525 74Hz.
    (II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 700x525 85Hz.
    (II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1440x900" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 720x450 60Hz.
    (II) SAVAGE(0): Not using default mode "720x450" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1600x1024" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 800x512 60Hz.
    (II) SAVAGE(0): Not using default mode "800x512" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1680x1050" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 840x525 60Hz.
    (II) SAVAGE(0): Not using default mode "840x525" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1920x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 960x600 60Hz.
    (II) SAVAGE(0): Not using default mode "960x600" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1920x1200" (exceeds panel dimensions)
    (--) SAVAGE(0): No suitable BIOS mode found for 960x600 72Hz.
    (II) SAVAGE(0): Not using default mode "960x600" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): No suitable BIOS mode found for 960x720 85Hz.
    (II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
    (II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): Chose mode 117 at 60Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): Chose mode 117 at 75Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
    (--) SAVAGE(0): Chose mode 117 at 85Hz.
    (II) SAVAGE(0): Not using default mode "1024x768" (hsync out of range)
    (--) SAVAGE(0): Chose mode 117 at 60Hz.
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (--) SAVAGE(0): Chose mode 114 at 60Hz.
    (--) SAVAGE(0): Chose mode 111 at 60Hz.
    (--) SAVAGE(0): Chose mode 11d at 70Hz.
    (--) SAVAGE(0): Chose mode 153 at 70Hz.
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (--) SAVAGE(0): Chose mode 143 at 72Hz.
    (--) SAVAGE(0): Chose mode 133 at 72Hz.
    (--) SAVAGE(0): Virtual size is 1024x768 (pitch 1024)
    (**) SAVAGE(0): *Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
    (II) SAVAGE(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
    (**) SAVAGE(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
    (II) SAVAGE(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
    (**) SAVAGE(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
    (II) SAVAGE(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
    (**) SAVAGE(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
    (II) SAVAGE(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
    (**) SAVAGE(0): Default mode "640x400": 41.7 MHz, 49.7 kHz, 60.0 Hz (D)
    (II) SAVAGE(0): Modeline "640x400" 41.73 640 672 740 840 400 400 402 414 doublescan
    (**) SAVAGE(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D)
    (II) SAVAGE(0): Modeline "512x384" 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync
    (**) SAVAGE(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
    (II) SAVAGE(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync
    (**) SAVAGE(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
    (II) SAVAGE(0): Modeline "400x300" 18.00 400 412 448 512 300 300 301 312 doublescan +hsync +vsync
    (**) SAVAGE(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
    (II) SAVAGE(0): Modeline "320x240" 12.60 320 328 376 400 240 245 246 262 doublescan -hsync -vsync
    (++) SAVAGE(0): DPI set to (96, 96)
    (II) Loading sub module "fb"
    (II) LoadModule: "fb"
    (II) Loading /usr/lib/xorg/modules/libfb.so
    (II) Module fb: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.3
    (II) Loading sub module "xaa"
    (II) LoadModule: "xaa"
    (II) Loading /usr/lib/xorg/modules/libxaa.so
    (II) Module xaa: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.2.0
    ABI class: X.Org Video Driver, version 1.0
    (II) Loading sub module "ramdac"
    (II) LoadModule: "ramdac"
    (II) Loading /usr/lib/xorg/modules/libramdac.so
    (II) Module ramdac: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 0.1.0
    ABI class: X.Org Video Driver, version 1.0
    (II) do I need RAC? No, I don't.
    (II) resource ranges after preInit:
    [0] 0 0 0xf0000000 - 0xf7ffffff (0x8000000) MS[B]
    [1] -1 0 0x00100000 - 0x11ffffff (0x11f00000) MX[B]E(B)
    [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
    [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
    [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [5] -1 0 0x12000800 - 0x12000fff (0x800) MX[B]
    [6] -1 0 0x12000000 - 0x120007ff (0x800) MX[B]
    [7] -1 0 0xe8000000 - 0xe80fffff (0x100000) MX[B]
    [8] -1 0 0xe8122000 - 0xe8122fff (0x1000) MX[B]
    [9] -1 0 0xe8121000 - 0xe8121fff (0x1000) MX[B]
    [10] -1 0 0xe8100000 - 0xe811ffff (0x20000) MX[B]
    [11] -1 0 0xe8120000 - 0xe8120fff (0x1000) MX[B]
    [12] -1 0 0xf8000000 - 0xf7ffffff (0x0) MX[B]O
    [13] -1 0 0xf0000000 - 0xf7ffffff (0x8000000) MX[B](B)
    [14] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
    [15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
    [16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
    [17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
    [18] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
    [19] -1 0 0x00001400 - 0x0000147f (0x80) IX[B]
    [20] -1 0 0x00001860 - 0x0000187f (0x20) IX[B]
    [21] -1 0 0x00001850 - 0x0000185f (0x10) IX[B]
    [22] -1 0 0x00001840 - 0x00001847 (0x8) IX[B]
    [23] -1 0 0x00001800 - 0x0000183f (0x40) IX[B]
    [24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
    [25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
    (II) Loading sub module "int10"
    (II) LoadModule: "int10"
    (II) Reloading /usr/lib/xorg/modules/libint10.so
    (II) SAVAGE(0): initializing int10
    (II) SAVAGE(0): Primary V_BIOS segment is: 0xc000
    (II) SAVAGE(0): VESA BIOS detected
    (II) SAVAGE(0): VESA VBE Version 2.0
    (II) SAVAGE(0): VESA VBE Total Mem: 8192 kB
    (II) SAVAGE(0): VESA VBE OEM: S3 Incorporated. M7 BIOS
    (II) SAVAGE(0): VESA VBE OEM Software Rev: 1.0
    (II) SAVAGE(0): VESA VBE OEM Vendor: S3 Incorporated.
    (II) SAVAGE(0): VESA VBE OEM Product: VBE 2.0
    (II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 1.1
    (II) SAVAGE(0): 4740 kB of Videoram needed for 3D; 8192 kB of Videoram available
    (II) SAVAGE(0): Sufficient Videoram available for 3D
    (II) SAVAGE(0): [drm] bpp: 16 depth: 16
    (II) SAVAGE(0): [drm] Sarea 2200+284: 2484
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is -1, (No such device or address)
    drmOpenDevice: open result is -1, (No such device or address)
    drmOpenDevice: Open failed
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is -1, (No such device or address)
    drmOpenDevice: open result is -1, (No such device or address)
    drmOpenDevice: Open failed
    drmOpenByBusid: Searching for BusID pci:0000:01:00.0
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 8, (OK)
    drmOpenByBusid: drmOpenMinor returns 8
    drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
    (II) SAVAGE(0): [drm] loaded kernel module for "savage" driver
    (II) SAVAGE(0): [drm] DRM interface version 1.2
    (II) SAVAGE(0): [drm] created "savage" driver at busid "pci:0000:01:00.0"
    (II) SAVAGE(0): [drm] added 8192 byte SAREA at 0xcce38000
    (II) SAVAGE(0): [drm] mapped SAREA 0xcce38000 to 0xa7ac7000
    (II) SAVAGE(0): [drm] framebuffer handle = 0xf0000000
    (II) SAVAGE(0): [drm] added 1 reserved context for kernel
    (II) SAVAGE(0): [agp] Mode 0x1f000201 [AGP 0x8086/0x7190; Card 0x5333/0x8c12]
    (II) SAVAGE(0): [agp] 16384 kB allocated with handle 0x00000001
    (II) SAVAGE(0): [agp] DMA buffers handle = 0xf8000000
    (II) SAVAGE(0): [agp] agpTextures handle = 0xf8200000
    (II) SAVAGE(0): [drm] aperture handle = 0xf2000000
    (II) SAVAGE(0): [drm] Enabling ShadowStatus for DRI.
    (II) SAVAGE(0): [drm] Status handle = 0x064c1000
    (II) SAVAGE(0): [drm] Status page mapped at 0xa7ac6000
    (II) SAVAGE(0): [drm] Added 32 65536 byte DMA buffers
    (II) SAVAGE(0): [dri] visual configs initialized
    (**) SAVAGE(0): DRI is enabled
    (--) SAVAGE(0): Chose mode 117 at 60Hz.
    (II) SAVAGE(0): virtualX:1024,virtualY:768
    (II) SAVAGE(0): bpp:16,tiledwidthBytes:2048,tiledBufferSize:1572864
    (II) SAVAGE(0): bpp:16,widthBytes:2048,BufferSize:1572864
    (II) SAVAGE(0): videoRambytes:0x00800000
    (II) SAVAGE(0): textureSize:0x0015f000
    (II) SAVAGE(0): textureSize:0x0015f000
    (II) SAVAGE(0): textureOffset:0x00680000
    (II) SAVAGE(0): depthOffset:0x00500000,depthPitch:2048
    (II) SAVAGE(0): backOffset:0x00380000,backPitch:2048
    (II) SAVAGE(0): Reserved back buffer at offset 0x380000
    (II) SAVAGE(0): Reserved depth buffer at offset 0x500000
    (II) SAVAGE(0): Reserved 1404 kb for textures at offset 0x680000
    (II) SAVAGE(0): Using 1023 lines for offscreen memory.
    (II) SAVAGE(0): Using XFree86 Acceleration Architecture (XAA)
    Screen to screen bit blits
    Solid filled rectangles
    8x8 mono pattern filled rectangles
    Indirect CPU to Screen color expansion
    Solid Lines
    Image Writes
    Offscreen Pixmaps
    Setting up tile and stipple cache:
    28 128x128 slots
    7 256x256 slots
    (==) SAVAGE(0): Backing store disabled
    (**) Option "dpms"
    (**) SAVAGE(0): DPMS enabled
    (II) SAVAGE(0): X context handle = 0x1
    (II) SAVAGE(0): [DRI] installation complete
    (II) SAVAGE(0): [junkers]pSAVAGEDRIServer:
    (II) SAVAGE(0): [junkers] reserved_map_agpstart:0x00000000
    (II) SAVAGE(0): [junkers] reserved_map_idx:0x00000000
    (II) SAVAGE(0): [junkers] sarea_priv_offset:0x00000000
    (II) SAVAGE(0): [junkers] chipset:0x00000000
    (II) SAVAGE(0): [junkers] sgram:0x00000000
    (II) SAVAGE(0): [junkers] frontbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] frontOffset:0x00000000
    (II) SAVAGE(0): [junkers] frontPitch:0x00000800
    (II) SAVAGE(0): [junkers] backbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] backOffset:0x00380000
    (II) SAVAGE(0): [junkers] backPitch:0x00000800
    (II) SAVAGE(0): [junkers] depthbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] depthOffset:0x00500000
    (II) SAVAGE(0): [junkers] depthPitch:0x00000800
    (II) SAVAGE(0): [junkers] textureOffset:0x00680000
    (II) SAVAGE(0): [junkers] textureSize:0x0015f000
    (II) SAVAGE(0): [junkers] textureSize:0x0015f000
    (II) SAVAGE(0): [junkers] logTextureGranularity:0x00000000
    (II) SAVAGE(0): [junkers] agp:handle:0x00000001
    (II) SAVAGE(0): [junkers] agp:offset:0x01000000
    (II) SAVAGE(0): [junkers] agp:size:0x01000000
    (II) SAVAGE(0): [junkers] agp:map:0x00000000
    (II) SAVAGE(0): [junkers] registers:handle:0xf1000000
    (II) SAVAGE(0): [junkers] registers:offset:0x00000000
    (II) SAVAGE(0): [junkers] registers:size:0x00080000
    (II) SAVAGE(0): [junkers] registers:map:0x00000000
    (II) SAVAGE(0): [junkers] status:handle:0x064c1000
    (II) SAVAGE(0): [junkers] status:offset:0x00000000
    (II) SAVAGE(0): [junkers] status:size:0x00001000
    (II) SAVAGE(0): [junkers] status:map:0xa7ac6000
    (II) SAVAGE(0): [junkers] agpTextures:handle:0xf8200000
    (II) SAVAGE(0): [junkers] agpTextures:offset:0x00200000
    (II) SAVAGE(0): [junkers] agpTextures:size:0x00e00000
    (II) SAVAGE(0): [junkers] apgTextures:map:0x00000000
    (II) SAVAGE(0): [junkers] logAgpTextureGranularity:0x00000000
    (II) SAVAGE(0): [junkers] cmdDma:handle:0x00000000
    (II) SAVAGE(0): [junkers] cmdDma:offset:0x00000000
    (II) SAVAGE(0): [junkers] cmdDma:size:0x00000000
    (II) SAVAGE(0): [junkers] cmdDma:map:0x00000000
    (II) SAVAGE(0): [junkers]pSAVAGEDRI:
    (II) SAVAGE(0): [junkers] chipset:0x00000002
    (II) SAVAGE(0): [junkers] width:0x00000400
    (II) SAVAGE(0): [junkers] height:0x00000300
    (II) SAVAGE(0): [junkers] mem:0x00800000
    (II) SAVAGE(0): [junkers] cpp:2
    (II) SAVAGE(0): [junkers] zpp:2
    (II) SAVAGE(0): [junkers] agpMode:1
    (II) SAVAGE(0): [junkers] bufferSize:65536
    (II) SAVAGE(0): [junkers] frontbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] frontOffset:0x00000000
    (II) SAVAGE(0): [junkers] backbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] backOffset:0x00380000
    (II) SAVAGE(0): [junkers] depthbufferSize:0x00180000
    (II) SAVAGE(0): [junkers] depthOffset:0x00500000
    (II) SAVAGE(0): [junkers] textureOffset:0x00680000
    (II) SAVAGE(0): [junkers] textureSize:0x00140000
    (II) SAVAGE(0): [junkers] logTextureGranularity:0x00000011
    (II) SAVAGE(0): [junkers] agpTextureHandle:0xf8200000
    (II) SAVAGE(0): [junkers] agpTextureSize:0x00e00000
    (II) SAVAGE(0): [junkers] logAgpTextureGranularity:0x00000014
    (II) SAVAGE(0): [junkers] apertureHandle:0xf2000000
    (II) SAVAGE(0): [junkers] apertureSize:0x05000000
    (II) SAVAGE(0): [junkers] aperturePitch:0x00002000
    (II) SAVAGE(0): [junkers] statusHandle:0x064c1000
    (II) SAVAGE(0): [junkers] statusSize:0x00001000
    (II) SAVAGE(0): [junkers] sarea_priv_offset:0x00000898
    (II) SAVAGE(0): Direct rendering enabled
    (==) RandR enabled
    (II) Initializing built-in extension MIT-SHM
    (II) Initializing built-in extension XInputExtension
    (II) Initializing built-in extension XTEST
    (II) Initializing built-in extension XKEYBOARD
    (II) Initializing built-in extension XC-APPGROUP
    (II) Initializing built-in extension SECURITY
    (II) Initializing built-in extension XINERAMA
    (II) Initializing built-in extension XFIXES
    (II) Initializing built-in extension XFree86-Bigfont
    (II) Initializing built-in extension RENDER
    (II) Initializing built-in extension RANDR
    (II) Initializing built-in extension COMPOSITE
    (II) Initializing built-in extension DAMAGE
    (II) Initializing built-in extension XEVIE
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 9, (OK)
    drmOpenByBusid: Searching for BusID pci:0000:01:00.0
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 9, (OK)
    drmOpenByBusid: drmOpenMinor returns 9
    drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
    (WW) AIGLX: 3D driver claims to not support visual 0x22
    (WW) AIGLX: 3D driver claims to not support visual 0x23
    (WW) AIGLX: 3D driver claims to not support visual 0x24
    (WW) AIGLX: 3D driver claims to not support visual 0x25
    (WW) AIGLX: 3D driver claims to not support visual 0x26
    (WW) AIGLX: 3D driver claims to not support visual 0x27
    (WW) AIGLX: 3D driver claims to not support visual 0x28
    (WW) AIGLX: 3D driver claims to not support visual 0x29
    (II) AIGLX: Loaded and initialized /usr/lib/dri/savage_dri.so
    (II) GLX: Initialized DRI GL provider for screen 0
    (**) Option "CoreKeyboard"
    (**) Generic Keyboard: Core Keyboard
    (**) Option "Protocol" "standard"
    (**) Generic Keyboard: Protocol: standard
    (**) Option "AutoRepeat" "500 30"
    (**) Option "XkbRules" "xorg"
    (**) Generic Keyboard: XkbRules: "xorg"
    (**) Option "XkbModel" "pc105"
    (**) Generic Keyboard: XkbModel: "pc105"
    (**) Option "XkbLayout" "de"
    (**) Generic Keyboard: XkbLayout: "de"
    (**) Option "XkbVariant" "nodeadkeys"
    (**) Generic Keyboard: XkbVariant: "nodeadkeys"
    (**) Option "CustomKeycodes" "off"
    (**) Generic Keyboard: CustomKeycodes disabled
    (**) Option "Protocol" "ImPS/2"
    (**) Configured Mouse: Device: "/dev/input/mice"
    (**) Configured Mouse: Protocol: "ImPS/2"
    (**) Option "CorePointer"
    (**) Configured Mouse: Core Pointer
    (**) Option "Device" "/dev/input/mice"
    (**) Option "Emulate3Buttons" "true"
    (**) Configured Mouse: Emulate3Buttons, Emulate3Timeout: 50
    (**) Configured Mouse: ZAxisMapping: buttons 4 and 5
    (**) Configured Mouse: Buttons: 9
    (II) Synaptics touchpad driver version 0.14.6 (1406)
    Synaptics Touchpad no synaptics event device found (checked 14 nodes)
    (**) Option "Device" "/dev/psaux"
    (**) Option "HorizScrollDelta" "0"
    Query no Synaptics: 6003C8
    (EE) Synaptics Touchpad no synaptics touchpad detected and no repeater device
    (EE) Synaptics Touchpad Unable to query/initialize Synaptics hardware.
    (EE) PreInit failed for input device "Synaptics Touchpad"
    (II) UnloadModule: "synaptics"
    (II) XINPUT: Adding extended input device "Configured Mouse" (type: MOUSE)
    (II) XINPUT: Adding extended input device "Generic Keyboard" (type: KEYBOARD)
    xkb_keycodes { include "xfree86+aliases(qwertz)" };
    xkb_types { include "complete" };
    xkb_compatibility { include "complete" };
    xkb_symbols { include "pc(pc105)+de(nodeadkeys)" };
    xkb_geometry { include "pc(pc105)" };
    (II) Configured Mouse: ps2EnableDataReporting: succeeded
    AUDIT: Mon Apr 16 20:17:46 2007: 3439 X: client 4 rejected from local host
    (II) SAVAGE(0): [drm] removed 1 reserved context for kernel
    (II) SAVAGE(0): [drm] unmapping 8192 bytes of SAREA 0xcce38000 at 0xa7ac7000
    (II) Open ACPI successful (/var/run/acpid.socket)
    (II) APM registered successfully
    (II) Loading sub module "int10"
    (II) LoadModule: "int10"
    (II) Reloading /usr/lib/xorg/modules/libint10.so
    (II) SAVAGE(0): initializing int10
    (II) SAVAGE(0): Primary V_BIOS segment is: 0xc000
    (II) SAVAGE(0): VESA BIOS detected
    (II) SAVAGE(0): VESA VBE Version 2.0
    (II) SAVAGE(0): VESA VBE Total Mem: 8192 kB
    (II) SAVAGE(0): VESA VBE OEM: S3 Incorporated. M7 BIOS
    (II) SAVAGE(0): VESA VBE OEM Software Rev: 1.0
    (II) SAVAGE(0): VESA VBE OEM Vendor: S3 Incorporated.
    (II) SAVAGE(0): VESA VBE OEM Product: VBE 2.0
    (II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 1.1
    (==) SAVAGE(0): Removed MMIO write-combining range (0xf0000000,0x1000000)
    (==) SAVAGE(0): Removed MMIO write-combining range (0xf0000000,0x1000000)
    (==) SAVAGE(0): Removed MMIO write-combining range (0xf2000000,0x2000000)
    (==) SAVAGE(0): Removed MMIO write-combining range (0xf4000000,0x4000000)
    (II) SAVAGE(0): 4740 kB of Videoram needed for 3D; 8192 kB of Videoram available
    (II) SAVAGE(0): Sufficient Videoram available for 3D
    (II) SAVAGE(0): [drm] bpp: 16 depth: 16
    (II) SAVAGE(0): [drm] Sarea 2200+284: 2484
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 8, (OK)
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 8, (OK)
    drmOpenByBusid: Searching for BusID pci:0000:01:00.0
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 8, (OK)
    drmOpenByBusid: drmOpenMinor returns 8
    drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
    (II) SAVAGE(0): [drm] DRM interface version 1.0
    (II) SAVAGE(0): [drm] drmSetBusid failed (8, pci:0000:01:00.0), Permission denied
    (EE) SAVAGE(0): [drm] DRIScreenInit failed. Disabling DRI.
    (EE) SAVAGE(0): DRI isn't enabled
    (--) SAVAGE(0): Chose mode 117 at 60Hz.
    (II) SAVAGE(0): Using 1280 lines for offscreen memory.
    (**) SAVAGE(0): DPMS enabled
    (WW) SAVAGE(0): Direct rendering disabled
    (==) RandR enabled
    (EE) AIGLX: Screen 0 is not DRI capable
    (II) Loading local sub module "GLcore"
    (II) LoadModule: "GLcore"
    (II) Loading /usr/lib/xorg/modules/extensions/libGLcore.so
    (II) Module GLcore: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (II) GLX: Initialized MESA-PROXY GL provider for screen 0
    xkb_keycodes { include "xfree86+aliases(qwertz)" };
    xkb_types { include "complete" };
    xkb_compatibility { include "complete" };
    xkb_symbols { include "pc(pc105)+de(nodeadkeys)" };
    xkb_geometry { include "pc(pc105)" };
    (II) Configured Mouse: ps2EnableDataReporting: succeeded
    AUDIT: Mon Apr 16 20:17:49 2007: 3439 X: client 2 rejected from local host
    ==============================================================================
    Hat jemand 'ne Idee zu diesem Problem ??
    Falls mehr (oder andere Informationen nötig sind ... nur Fragen.
    Ciao Uwe[/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B]
     
  2. Anzeige

    Schau dir mal diese Kategorie an. Dort findest du bestimmt etwas.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  3. Shorti

    Shorti Routinier

    Dabei seit:
    08.04.2007
    Beiträge:
    271
    Zustimmungen:
    0
    da gabs doch ma so code-tags, oder irre ich mich?

    PS.:
    Es tut mir leid wenn dass vielleich blöde rüber kommt, aber du würdest uns allen einen gefallen tun codetags zu benutzen.
     
  4. #3 uwe_911, 16.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    DAnke für deine Antwort, aber was sind code-tags ??
    M.f.G
    Uwe
     
  5. buli

    buli Debianator

    Dabei seit:
    16.09.2006
    Beiträge:
    789
    Zustimmungen:
    0
    Ort:
    Essen/Ruhrgebiet
    Code:
    [ code ] ..... [ /code ]
    Kannst du mit einem Klick auf das Rautezeichen bewirken (#)
     
  6. #5 uwe_911, 16.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    mea culpa. Werde es bei meinem nächsten Posting beherzigen.
    M.f.G
    Uwe
     
  7. #6 Bâshgob, 16.04.2007
    Zuletzt bearbeitet: 16.04.2007
    Bâshgob

    Bâshgob freies Radikal

    Dabei seit:
    29.07.2004
    Beiträge:
    2.334
    Zustimmungen:
    0
    Ort:
    Hannover
    Zum Thema selbst: Das Problem liegt sicherlich nicht beim DRI, sondern eher beim APIC oder ACPI.

    Ich fahre ein T23 nur mit APM, ACPI läuft da nicht richtig und verursacht derartige Probleme. Ggf. hilft schon ein BIOSupdate.

    Lesestoff:

    http://www.thinkwiki.org/wiki/Category:T22

    Schau mal durch und gib mal Rückmeldung.
     
  8. #7 uwe_911, 16.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    Schön und Gut. Danke für den Hinweis. Jetzt hab ich natürlich das Problem: an welchem Parameter muss ich drehen ?
    M.f.G.
    Uwe
     
  9. #8 Bâshgob, 16.04.2007
    Bâshgob

    Bâshgob freies Radikal

    Dabei seit:
    29.07.2004
    Beiträge:
    2.334
    Zustimmungen:
    0
    Ort:
    Hannover
    Gibst grub beim Start halt noapic oder noacpi mit.
     
  10. #9 uwe_911, 17.04.2007
    Zuletzt bearbeitet: 17.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    @Bashgob, da hast Du mir jede Menge zum lesen gegeben.
    Bin dabei. Sollte es jedoch zum Kernel-Neu-Bauen kommen werde ich passen und mir ein anderes Gerät kaufen.
    .
    .
    .
    EDIT (autom. Beitragszusammenführung) :
    .

    Hallo. ich bin begeistert.
    Der grub Parameter >noacpi< hat es gebracht.
    M.f.G
    Uwe
     
  11. #10 Bâshgob, 17.04.2007
    Bâshgob

    Bâshgob freies Radikal

    Dabei seit:
    29.07.2004
    Beiträge:
    2.334
    Zustimmungen:
    0
    Ort:
    Hannover
    Wenn du dann dennoch nicht auf Powermanagement verzichten willst probierst du folgendes:

    Code:
    modprobe apm
    Damit geht bei mir zumindest Standby und suspend-2-RAM. Und mit ein wenig Gefrickel sogar Hibernate (mit dem kleinen Schönheitsfehler, das nach dem Erwecken der Sound nicht mehr geht. Alle bisher versuchten Tricks brachten leider nix :( )
     
  12. Anzeige

    Vielleicht findest du HIER Antworten.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  13. #11 uwe_911, 17.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    Das werde ich heute Abend mal testen. Obwohl der T22 dauernd am Netz läuft und weder Bildschirm noch HDD abschalten soll. (der Akku hat die typische IBM Schwäche)
    Nochmal vielen Dank für Deinen Tipp
     
  14. #12 uwe_911, 20.04.2007
    uwe_911

    uwe_911 Jungspund

    Dabei seit:
    21.03.2007
    Beiträge:
    13
    Zustimmungen:
    0
    Ort:
    RM Gebiet
    Hier noch ein Nachschlag zu diesem Theme
    Code:
    Mobilix:/home/kniza# modprobe -l apm
    /lib/modules/2.6.18-4-686/kernel/arch/i386/kernel/apm.ko
    Mobilix:/home/kniza# modprobe -nv apm
    insmod /lib/modules/2.6.18-4-686/kernel/arch/i386/kernel/apm.ko
    Mobilix:/home/kniza# modprobe  apm
    FATAL: Error inserting apm (/lib/modules/2.6.18-4-686/kernel/arch/i386/kernel/apm.ko): No such device
    
    Ist aber nicht der Knackpunkt, weil s.o.Section "Module"

    habe noch in der xorg.conf diese Änderung gemacht
    Code:
    Section "Module"
        Load    "i2c"
        Load    "bitmap"
        Load    "ddc"
    #    Load    "dri"
        Load    "extmod"
        Load    "freetype"
        Load    "glx"
        Load    "int10"
        Load    "vbe"
    
    Jetzt läuft es rund.
     
Thema:

IBM T22, Debian Etch 4, X-server start nach Neuinstall

Die Seite wird geladen...

IBM T22, Debian Etch 4, X-server start nach Neuinstall - Ähnliche Themen

  1. Der Freeze-Termin für Debian 9 »Stretch« wird verschoben

    Der Freeze-Termin für Debian 9 »Stretch« wird verschoben: Der Beginn der Vorbereitung zur Veröffentlichung, der nächsten Version Debian 9, bei Debian »Freeze« genannt, wird um zwei Monate nach hinten...
  2. Debian Stretch: Installer erreicht erste Alpha

    Debian Stretch: Installer erreicht erste Alpha: Die erste Alphaversion des Debian-Installers 9.0 läutet eine neue Phase der Debian-Entwicklung ein. Trotzdem ist Debian 9 noch fast zwei Jahre...
  3. Debian etch mit kernel 2.4

    Debian etch mit kernel 2.4: Hallo, ich habe einen alten Rechner und will/muss etch benutzen. Wollte mal einfach nur wissen, ob etch auch mit einem kernel 2.4.31 läuft?...
  4. Probs mit PDC auf Debian Etch

    Probs mit PDC auf Debian Etch: Hallo Forum ich habe einen PDC mit Samba unter Debian eingerichtet. Wenn ein Rechner versucht in die Domäne einzutreten kommt immer die Meldung,...
  5. debian lenny: fetchmail

    debian lenny: fetchmail: Hi, ich habe hier ein komisches phänomen benutze ich fetchmail als benutzer (über cron) funktioniert alles .. benutze ich es als daemon...