CENTOS - DGE-528T GBit Netzwerkkarte wird nicht erkannt

Dieses Thema im Forum "Sonstiges" wurde erstellt von C02, 25.12.2006.

  1. #1 C02, 25.12.2006
    Zuletzt bearbeitet: 25.12.2006
    C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Erstmal HAllo und Frohe Weihanchten

    Habe das Problem das die oben genannte NEtzwerkkarte nicht erkannt wird.

    wenn ich ifconfig machen wir nur lo angezeigt.
    ifconfig et0 up bringt auch kein Erfolg.

    Die Treiber auch dlink.de sind nur für den 2.4 er Kernel.
    Habe jetzt gelesen das die Karte einen Realtek RTL8169 Chipsatz hat.
    Also die Treiber von der Karte geladen. Nur leider sind meine Linux Kentnisse nicht ganz so toll und ich schaffe es deshalb nciht die Treiber zu installieren.
    Dies ist die Anleitung zu der Installation:

    Code:
    This is the Linux device driver released for RealTek Ethernet controllers, which are listed as following.
    	1. RTL8169S/SB/SC (Gigabit Ethernet with PCI interface)
    	2. RTL8168B (Gigabit Ethernet with PCI-Express interface)
    	3. RTL8101E (Fast Ethernet with PCI-Express interface)
    
    <Requirements>
    
      - kernel source tree (supported versions 2.4.x or 2.6.x)
      - compiler/binutils for kernel compilation
    
    
    
    <Quick install with proper kernel settings>
    
      Unpack the tarball :
    	tar vzxf r1000_vX.YZ.tgz
    
      Change to the directory:
    	cd r1000_vX.YZ
    
      If you are running the target kernel, then you should be
      able to do :
    
    	make clean modules	(as root or with sudo)
    	make install
    	depmod -a
    
    Wenn ich jetzt "make install modules " in dem Ordner eingebe kommen viel Fehlermeldungen.
    ICh bin mir auch nicht sicher ob ich die "requirements" erfülle.
    Hat zufällig jemand die Karte und weiß wies einfacher geht?



    EDIT:

    Habe außerdem diesen Beitrag gefunden:
    Habe also nach dme Modul gesucht und es unter /lib/modules/.../drivers/net gefunden
    Wenn ich dann aber "modprobe r8169.ko" eingebe kommt der Text
    " Module r8169.ko not found "

    MFG
    Co2
     
  2. Anzeige

    Schau dir mal diese Kategorie an. Dort findest du bestimmt etwas.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  3. theton

    theton Bitmuncher

    Dabei seit:
    27.05.2004
    Beiträge:
    4.820
    Zustimmungen:
    0
    Ort:
    Berlin, Germany
    Du darfst die Endung beim Laden des Moduls nicht mit angeben, also
    Code:
    modprobe r8169
    
     
  4. #3 C02, 25.12.2006
    Zuletzt bearbeitet: 25.12.2006
    C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Ah ok das wusste ich nicht.

    Wenn ich jetzt den Befehl ausführe kommt keine Fehlermeldung mehr. Die Netzwerkkarte wird jedoch trotzdem nicht angezeigt.

    Eine Idee ?


    MFG
    C02
     
  5. #4 kbdcalls, 25.12.2006
    kbdcalls

    kbdcalls Master of Universe

    Dabei seit:
    16.10.2006
    Beiträge:
    518
    Zustimmungen:
    0
    Was für eine Fehlermeldung ? Was ergibt
    Code:
    ifconfig -a
     
  6. C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Also ich habe zur Zeit 2 Netzwerkkarten drin weil die eine ja nciht geht.

    Eth0 funktioniert (100Mbit)
    und die 1Gbit Karte wird nicht angezeigt.

    Wenn ich ifconfig -a mache wird folgendes angezeigt :

    eth0 ...

    l0...

    sit0 (IPv6 nach IPv4)...


    Jedoch nichts von meiner zweiten KArte.
     
  7. #6 kbdcalls, 25.12.2006
    kbdcalls

    kbdcalls Master of Universe

    Dabei seit:
    16.10.2006
    Beiträge:
    518
    Zustimmungen:
    0
    Die Fehlermeldung ?
     
  8. C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Es kommt keine Fehlermeldung, was meinst du ?
     
  9. C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Kann ich überprüfen ob die Karte erkannt wird ?
    Ich habe mir die Krte extra gekauft weil sie einen Linux unterstützung hatte, und jetzt das...
     
  10. theton

    theton Bitmuncher

    Dabei seit:
    27.05.2004
    Beiträge:
    4.820
    Zustimmungen:
    0
    Ort:
    Berlin, Germany
    Du kannst mal einen Blick in die /var/log/messages werfen um zu sehen, ob es evtl. doch Probleme beim Laden des Moduls gibt.
     
  11. Anzeige

    Vielleicht findest du HIER Antworten.
    Registrieren bzw. einloggen, um diese und auch andere Anzeigen zu deaktivieren
  12. C02

    C02 Grünschnabel

    Dabei seit:
    25.12.2006
    Beiträge:
    8
    Zustimmungen:
    0
    Sehe dort nichts merkwürdiges.
    Habe die datei neu angelegt nur die neue Netzwerkkarte reingesetzt(alte rausgenommen) und gebootet. Das wurde dann in der messages datei angezeigt:


    Code:
    Dec 27 00:41:57 localhost syslogd 1.4.1: restart.
    Dec 27 00:41:57 localhost syslog: Starten von syslogd succeeded
    Dec 27 00:41:57 localhost kernel: klogd 1.4.1, log source = /proc/kmsg started.
    Dec 27 00:41:57 localhost kernel: Linux version 2.6.9-42.0.3.EL (buildsvn@build-i386) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 Fri Oct 6 05:59:54 CDT 2006
    Dec 27 00:41:57 localhost kernel: BIOS-provided physical RAM map:
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 0000000000100000 - 000000000fffc000 (usable)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 000000000fffc000 - 000000000ffff000 (ACPI data)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    Dec 27 00:41:57 localhost kernel:  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
    Dec 27 00:41:57 localhost syslog: Starten von klogd succeeded
    Dec 27 00:41:57 localhost kernel: 0MB HIGHMEM available.
    Dec 27 00:41:57 localhost kernel: 255MB LOWMEM available.
    Dec 27 00:41:57 localhost kernel: Using x86 segment limits to approximate NX protection
    Dec 27 00:41:57 localhost kernel: zapping low mappings.
    Dec 27 00:41:57 localhost kernel: DMI 2.3 present.
    Dec 27 00:41:57 localhost irqbalance: Starten von irqbalance succeeded
    Dec 27 00:41:57 localhost kernel: ACPI: PM-Timer IO Port: 0xe408
    Dec 27 00:41:57 localhost kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Dec 27 00:41:57 localhost kernel: Processor #0 6:4 APIC version 16
    Dec 27 00:41:57 localhost kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    Dec 27 00:41:57 localhost kernel: Enabling APIC mode:  Flat.  Using 0 I/O APICs
    Dec 27 00:41:57 localhost kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    Dec 27 00:41:57 localhost kernel: IOAPIC[0]: apic_id 2, version 2, address 0xfec00000, GSI 0-23
    Dec 27 00:41:57 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
    Dec 27 00:41:57 localhost kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    Dec 27 00:41:57 localhost kernel: Using ACPI (MADT) for SMP configuration information
    Dec 27 00:41:57 localhost kernel: Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
    Dec 27 00:41:57 localhost kernel: Built 1 zonelists
    Dec 27 00:41:57 localhost kernel: Kernel command line: ro root=/dev/VolGroup00/LogVol00
    Dec 27 00:41:57 localhost kernel: Initializing CPU#0
    Dec 27 00:41:57 localhost kernel: CPU 0 irqstacks, hard=c0400000 soft=c03ff000
    Dec 27 00:41:57 localhost kernel: PID hash table entries: 1024 (order: 10, 16384 bytes)
    Dec 27 00:41:57 localhost kernel: Detected 852.396 MHz processor.
    Dec 27 00:41:57 localhost kernel: Using pmtmr for high-res timesource
    Dec 27 00:41:57 localhost kernel: Console: colour VGA+ 80x25
    Dec 27 00:41:57 localhost kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Dec 27 00:41:57 localhost kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Dec 27 00:41:57 localhost kernel: Memory: 254392k/262128k available (2150k kernel code, 7100k reserved, 716k data, 164k init, 0k highmem)
    Dec 27 00:41:57 localhost kernel: Calibrating delay using timer specific routine.. 1705.22 BogoMIPS (lpj=852611)
    Dec 27 00:41:57 localhost kernel: Security Scaffold v1.0.0 initialized
    Dec 27 00:41:57 localhost kernel: SELinux:  Initializing.
    Dec 27 00:41:57 localhost kernel: SELinux:  Starting in permissive mode
    Dec 27 00:41:57 localhost kernel: There is already a security framework initialized, register_security failed.
    Dec 27 00:41:57 localhost kernel: selinux_register_security:  Registering secondary module capability
    Dec 27 00:41:57 localhost kernel: Capability LSM initialized as secondary
    Dec 27 00:41:57 localhost kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    Dec 27 00:41:57 localhost kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    Dec 27 00:41:57 localhost kernel: CPU: L2 Cache: 256K (64 bytes/line)
    Dec 27 00:41:57 localhost kernel: Intel machine check architecture supported.
    Dec 27 00:41:57 localhost kernel: Intel machine check reporting enabled on CPU#0.
    Dec 27 00:41:57 localhost kernel: CPU: AMD Athlon (TM) stepping 02
    Dec 27 00:41:57 localhost kernel: Enabling fast FPU save and restore... done.
    Dec 27 00:41:57 localhost kernel: Checking 'hlt' instruction... OK.
    Dec 27 00:41:57 localhost kernel: ENABLING IO-APIC IRQs
    Dec 27 00:41:57 localhost kernel: ..TIMER: vector=0x31 pin1=2 pin2=-1
    Dec 27 00:41:58 localhost kernel: checking if image is initramfs... it is
    Dec 27 00:41:58 localhost kernel: Freeing initrd memory: 1123k freed
    Dec 27 00:41:58 localhost kernel: NET: Registered protocol family 16
    Dec 27 00:41:58 localhost kernel: PCI: PCI BIOS revision 2.10 entry at 0xf17e0, last bus=1
    Dec 27 00:41:58 localhost kernel: PCI: Using configuration type 1
    Dec 27 00:41:58 localhost kernel: mtrr: v2.0 (20020519)
    Dec 27 00:41:58 localhost kernel: ACPI: Subsystem revision 20040816
    Dec 27 00:41:58 localhost kernel: ACPI: Interpreter enabled
    Dec 27 00:41:58 localhost kernel: ACPI: Using IOAPIC for interrupt routing
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    Dec 27 00:41:58 localhost portmap: Starten von portmap succeeded
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14) *9
    Dec 27 00:41:58 localhost kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
    Dec 27 00:41:58 localhost kernel: PCI: Probing PCI hardware (bus 00)
    Dec 27 00:41:58 localhost kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
    Dec 27 00:41:58 localhost kernel: usbcore: registered new driver usbfs
    Dec 27 00:41:58 localhost kernel: usbcore: registered new driver hub
    Dec 27 00:41:58 localhost kernel: PCI: Using ACPI for IRQ routing
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 177
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:09.1[B] -> GSI 16 (level, low) -> IRQ 185
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:09.2[C] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 185
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:11.1[A]: no GSI - using IRQ 0
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 193
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 193
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 185
    Dec 27 00:41:58 localhost kernel: Simple Boot Flag at 0x3a set to 0x1
    Dec 27 00:41:58 localhost kernel: apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    Dec 27 00:41:58 localhost kernel: apm: overridden by ACPI.
    Dec 27 00:41:58 localhost kernel: audit: initializing netlink socket (disabled)
    Dec 27 00:41:58 localhost kernel: audit(1167180082.655:1): initialized
    Dec 27 00:41:58 localhost kernel: Total HugeTLB memory allocated, 0
    Dec 27 00:41:58 localhost kernel: VFS: Disk quotas dquot_6.5.1
    Dec 27 00:41:58 localhost kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Dec 27 00:41:58 localhost kernel: SELinux:  Registering netfilter hooks
    Dec 27 00:41:58 localhost kernel: Initializing Cryptographic API
    Dec 27 00:41:58 localhost kernel: ksign: Installing public key data
    Dec 27 00:41:58 localhost kernel: Loading keyring
    Dec 27 00:41:58 localhost kernel: - Added public key 43FDDC2AA0FF41CC
    Dec 27 00:41:58 localhost kernel: - User ID: CentOS (Kernel Module GPG key)
    Dec 27 00:41:58 localhost kernel: PCI: Via IRQ fixup for 0000:00:09.0, from 5 to 1
    Dec 27 00:41:58 localhost kernel: PCI: Via IRQ fixup for 0000:00:09.1, from 11 to 9
    Dec 27 00:41:58 localhost kernel: PCI: Via IRQ fixup for 0000:00:11.2, from 0 to 1
    Dec 27 00:41:58 localhost kernel: PCI: Via IRQ fixup for 0000:00:11.3, from 9 to 1
    Dec 27 00:41:58 localhost kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    Dec 27 00:41:58 localhost kernel: ACPI: Processor [CPU0] (supports C1)
    Dec 27 00:41:58 localhost kernel: Real Time Clock Driver v1.12
    Dec 27 00:41:58 localhost kernel: Linux agpgart interface v0.100 (c) Dave Jones
    Dec 27 00:41:58 localhost kernel: agpgart: Detected VIA KT266/KY266x/KT333 chipset
    Dec 27 00:41:58 localhost kernel: agpgart: Maximum main memory to use for agp memory: 203M
    Dec 27 00:41:58 localhost kernel: agpgart: AGP aperture is 32M @ 0xfc000000
    Dec 27 00:41:58 localhost kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
    Dec 27 00:41:58 localhost kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
    Dec 27 00:41:58 localhost kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
    Dec 27 00:41:58 localhost kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    Dec 27 00:41:58 localhost kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    Dec 27 00:41:58 localhost kernel: RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    Dec 27 00:41:58 localhost rpc.statd[2660]: Version 1.0.6 Starting
    Dec 27 00:41:58 localhost kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    Dec 27 00:41:58 localhost kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    Dec 27 00:41:58 localhost kernel: VP_IDE: IDE controller at PCI slot 0000:00:11.1
    Dec 27 00:41:58 localhost nfslock: Starten von rpc.statd succeeded
    Dec 27 00:41:58 localhost kernel: ACPI: PCI interrupt 0000:00:11.1[A]: no GSI - using IRQ 0
    Dec 27 00:41:58 localhost rpc.statd[2660]: statd running as root. chown /var/lib/nfs/statd/sm to choose different user 
    Dec 27 00:41:58 localhost kernel: VP_IDE: chipset revision 6
    Dec 27 00:41:58 localhost kernel: VP_IDE: not 100% native mode: will probe irqs later
    Dec 27 00:41:58 localhost kernel: VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    Dec 27 00:41:58 localhost kernel:     ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:pio
    Dec 27 00:41:58 localhost kernel:     ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
    Dec 27 00:41:58 localhost kernel: hda: IC35L060AVVA07-0, ATA DISK drive
    Dec 27 00:41:58 localhost kernel: Using cfq io scheduler
    Dec 27 00:41:58 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Dec 27 00:41:58 localhost kernel: hda: max request size: 128KiB
    Dec 27 00:41:58 localhost kernel: hda: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
    Dec 27 00:41:58 localhost kernel:  hda: hda1 hda2
    Dec 27 00:41:58 localhost kernel: ide-floppy driver 0.99.newide
    Dec 27 00:41:58 localhost kernel: usbcore: registered new driver hiddev
    Dec 27 00:41:58 localhost kernel: usbcore: registered new driver usbhid
    Dec 27 00:41:58 localhost kernel: drivers/usb/input/hid-core.c: v2.0:USB HID core driver
    Dec 27 00:41:58 localhost kernel: mice: PS/2 mouse device common for all mice
    Dec 27 00:41:58 localhost kernel: input: AT Translated Set 2 keyboard on isa0060/serio0
    Dec 27 00:41:58 localhost kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    Dec 27 00:41:58 localhost kernel: NET: Registered protocol family 2
    Dec 27 00:41:58 localhost kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    Dec 27 00:41:58 localhost kernel: TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    Dec 27 00:41:58 localhost kernel: TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
    Dec 27 00:41:58 localhost kernel: TCP: Hash tables configured (established 16384 bind 16384)
    Dec 27 00:41:58 localhost kernel: Initializing IPsec netlink socket
    Dec 27 00:41:58 localhost kernel: NET: Registered protocol family 1
    Dec 27 00:41:58 localhost kernel: NET: Registered protocol family 17
    Dec 27 00:41:58 localhost kernel: ACPI: (supports S0 S1 S4 S5)
    Dec 27 00:41:58 localhost kernel: ACPI wakeup devices: 
    Dec 27 00:41:58 localhost kernel: PCI0 PCI1 UAR1 USB0 USB1 
    Dec 27 00:41:58 localhost kernel: Freeing unused kernel memory: 164k freed
    Dec 27 00:41:58 localhost kernel: SCSI subsystem initialized
    Dec 27 00:41:58 localhost kernel: device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email]dm-devel@redhat.com[/email]
    Dec 27 00:41:58 localhost kernel: kjournald starting.  Commit interval 5 seconds
    Dec 27 00:41:58 localhost kernel: EXT3-fs: mounted filesystem with ordered data mode.
    Dec 27 00:41:58 localhost kernel: SELinux:  Disabled at runtime.
    Dec 27 00:41:58 localhost kernel: SELinux:  Unregistering netfilter hooks
    Dec 27 00:41:59 localhost kernel: inserting floppy driver for 2.6.9-42.0.3.EL
    Dec 27 00:41:59 localhost kernel: Floppy drive(s): fd0 is 1.44M
    Dec 27 00:41:59 localhost kernel: FDC 0 is a post-1991 82077
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:59 localhost kernel: ata1: SATA max UDMA/133 cmd 0xD082A200 ctl 0xD082A238 bmdma 0x0 irq 169
    Dec 27 00:41:59 localhost kernel: ata2: SATA max UDMA/133 cmd 0xD082A280 ctl 0xD082A2B8 bmdma 0x0 irq 169
    Dec 27 00:41:59 localhost kernel: ata3: SATA max UDMA/133 cmd 0xD082A300 ctl 0xD082A338 bmdma 0x0 irq 169
    Dec 27 00:41:59 localhost kernel: ata4: SATA max UDMA/133 cmd 0xD082A380 ctl 0xD082A3B8 bmdma 0x0 irq 169
    Dec 27 00:41:59 localhost kernel: ata1: SATA link down (SStatus 0)
    Dec 27 00:41:59 localhost kernel: scsi0 : sata_promise
    Dec 27 00:41:59 localhost kernel: ata2: SATA link down (SStatus 0)
    Dec 27 00:41:59 localhost kernel: scsi1 : sata_promise
    Dec 27 00:41:59 localhost kernel: ata3: SATA link down (SStatus 0)
    Dec 27 00:41:59 localhost kernel: scsi2 : sata_promise
    Dec 27 00:41:59 localhost kernel: ata4: SATA link down (SStatus 0)
    Dec 27 00:41:59 localhost kernel: scsi3 : sata_promise
    Dec 27 00:41:59 localhost kernel: USB Universal Host Controller Interface driver v2.2
    Dec 27 00:41:59 localhost rpcidmapd: Starten von rpc.idmapd succeeded
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 177
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.0: UHCI Host Controller
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.0: irq 177, io base 0000d400
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
    Dec 27 00:41:59 localhost kernel: hub 1-0:1.0: USB hub found
    Dec 27 00:41:59 localhost kernel: hub 1-0:1.0: 2 ports detected
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:09.1[B] -> GSI 16 (level, low) -> IRQ 185
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.1: UHCI Host Controller
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.1: irq 185, io base 0000d000
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 2
    Dec 27 00:41:59 localhost kernel: hub 2-0:1.0: USB hub found
    Dec 27 00:41:59 localhost kernel: hub 2-0:1.0: 2 ports detected
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 193
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.2: UHCI Host Controller
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.2: irq 193, io base 0000a400
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 3
    Dec 27 00:41:59 localhost kernel: hub 3-0:1.0: USB hub found
    Dec 27 00:41:59 localhost kernel: hub 3-0:1.0: 2 ports detected
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 193
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.3: UHCI Host Controller
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.3: irq 193, io base 0000a000
    Dec 27 00:41:59 localhost kernel: uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 4
    Dec 27 00:41:59 localhost kernel: hub 4-0:1.0: USB hub found
    Dec 27 00:41:59 localhost kernel: hub 4-0:1.0: 2 ports detected
    Dec 27 00:41:59 localhost kernel: ACPI: PCI interrupt 0000:00:09.2[C] -> GSI 17 (level, low) -> IRQ 169
    Dec 27 00:41:59 localhost kernel: ehci_hcd 0000:00:09.2: EHCI Host Controller
    Dec 27 00:41:59 localhost kernel: ehci_hcd 0000:00:09.2: irq 169, pci mem d084e000
    Dec 27 00:41:59 localhost kernel: ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 5
    Dec 27 00:41:59 localhost kernel: ehci_hcd 0000:00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
    Dec 27 00:41:59 localhost kernel: hub 5-0:1.0: USB hub found
    Dec 27 00:41:59 localhost kernel: hub 5-0:1.0: 4 ports detected
    Dec 27 00:41:59 localhost kernel: md: Autodetecting RAID arrays.
    Dec 27 00:41:59 localhost kernel: md: autorun ...
    Dec 27 00:41:59 localhost kernel: md: ... autorun DONE.
    Dec 27 00:41:59 localhost kernel: ACPI: Power Button (FF) [PWRF]
    Dec 27 00:41:59 localhost kernel: EXT3 FS on dm-0, internal journal
    Dec 27 00:41:59 localhost kernel: kjournald starting.  Commit interval 5 seconds
    Dec 27 00:41:59 localhost kernel: EXT3 FS on hda1, internal journal
    Dec 27 00:41:59 localhost kernel: EXT3-fs: mounted filesystem with ordered data mode.
    Dec 27 00:41:59 localhost kernel: Adding 524280k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1
    Dec 27 00:41:59 localhost kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
    Dec 27 00:41:59 localhost kernel: parport0: irq 7 detected
    Dec 27 00:41:59 localhost kernel: ip_tables: (C) 2000-2002 Netfilter core team
    Dec 27 00:42:00 localhost netfs: Andere Dateisysteme einhängen:  succeeded
    Dec 27 01:41:31 localhost rc.sysinit: -e 
    Dec 27 01:41:33 localhost start_udev: udev starten:  succeeded 
    Dec 27 01:41:35 localhost udevsend[1309]: starting udevd daemon 
    Dec 27 01:41:43 localhost rc.sysinit: -e 
    Dec 27 01:41:43 localhost sysctl: net.ipv4.ip_forward = 0 
    Dec 27 01:41:43 localhost sysctl: net.ipv4.conf.default.rp_filter = 1 
    Dec 27 01:41:43 localhost sysctl: net.ipv4.conf.default.accept_source_route = 0 
    Dec 27 01:41:43 localhost sysctl: kernel.sysrq = 0 
    Dec 27 01:41:43 localhost sysctl: kernel.core_uses_pid = 1 
    Dec 27 01:41:43 localhost rc.sysinit: Kernelparameter konfigurieren:  succeeded 
    Dec 27 00:41:41 localhost date: Mi Dez 27 00:41:41 CET 2006 
    Dec 27 00:41:41 localhost rc.sysinit: Stelle Uhr  (localtime) auf: Mi Dez 27 00:41:41 CET 2006 succeeded 
    Dec 27 00:41:41 localhost rc.sysinit: Standardmäßige Tastenbelegung laden succeeded 
    Dec 27 00:41:41 localhost rc.sysinit: Rechnername localhost.localdomain einstellen:  succeeded 
    Dec 27 00:41:41 localhost fsck: /dev/VolGroup00/LogVol00: clean, 84534/7421952 files, 792509/14843904 blocks 
    Dec 27 00:41:41 localhost rc.sysinit: Root-Dateisystem prüfen:  succeeded 
    Dec 27 00:41:41 localhost rc.sysinit: Root-Dateisystem mit Schreib- und Lesezugriff neu einhängen:  succeeded 
    Dec 27 00:41:41 localhost lvm.static:   2 logical volume(s) in volume group VolGroup00 now active 
    Dec 27 00:41:41 localhost rc.sysinit: Logical Volume Management einrichten: succeeded 
    Dec 27 00:41:42 localhost fsck: /boot: clean, 38/26104 files, 15969/104388 blocks 
    Dec 27 00:41:42 localhost rc.sysinit: Dateisysteme prüfen succeeded 
    Dec 27 00:41:42 localhost rc.sysinit: Lokale Dateisysteme einhängen:  succeeded 
    Dec 27 00:41:42 localhost rc.sysinit: Quota für lokale Dateisysteme aktivieren:  succeeded 
    Dec 27 00:41:42 localhost rc.sysinit: Swap-Bereich aktivieren:  succeeded 
    Dec 27 00:41:42 localhost init: Entering runlevel: 3 
    Dec 27 00:41:56 localhost kudzu:  succeeded 
    Dec 27 00:41:57 localhost rc: pcmcia starten:  succeeded 
    Dec 27 00:41:57 localhost sysctl: net.ipv4.ip_forward = 0 
    Dec 27 00:41:57 localhost sysctl: net.ipv4.conf.default.rp_filter = 1 
    Dec 27 00:41:57 localhost sysctl: net.ipv4.conf.default.accept_source_route = 0 
    Dec 27 00:41:57 localhost sysctl: kernel.sysrq = 0 
    Dec 27 00:41:57 localhost sysctl: kernel.core_uses_pid = 1 
    Dec 27 00:41:57 localhost network: Netzwerkparameter einstellen:  succeeded 
    Dec 27 00:41:57 localhost network: Loopback Schnittstelle hochfahren:  succeeded 
    Dec 27 00:42:00 localhost autofs: automount startup succeeded
    Dec 27 00:42:00 localhost smartd[2749]: smartd version 5.33 [i686-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen 
    Dec 27 00:42:00 localhost smartd[2749]: Home page is [url]http://smartmontools.sourceforge.net/[/url]  
    Dec 27 00:42:00 localhost smartd[2749]: Opened configuration file /etc/smartd.conf 
    Dec 27 00:42:00 localhost smartd[2749]: Configuration file /etc/smartd.conf parsed. 
    Dec 27 00:42:00 localhost smartd[2749]: Device: /dev/hda, opened 
    Dec 27 00:42:00 localhost smartd[2749]: Device: /dev/hda, found in smartd database. 
    Dec 27 00:42:01 localhost smartd[2749]: Device: /dev/hda, is SMART capable. Adding to "monitor" list. 
    Dec 27 00:42:01 localhost smartd[2749]: Device: /dev/sda, No such device, open() failed 
    Dec 27 00:42:01 localhost smartd[2749]: Unable to register ATA device /dev/sda at line 31 of file /etc/smartd.conf 
    Dec 27 00:42:01 localhost smartd[2749]: Unable to register device /dev/sda (no Directive -d removable). Exiting. 
    Dec 27 00:42:01 localhost smartd: Starten von smartd failed
    Dec 27 00:42:01 localhost acpid: Starten von acpid succeeded
    Dec 27 00:42:03 localhost kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
    Dec 27 00:42:03 localhost kernel: parport0: irq 7 detected
    Dec 27 00:42:03 localhost kernel: lp0: using parport0 (polling).
    Dec 27 00:42:03 localhost kernel: lp0: console ready
    Dec 27 00:42:03 localhost cups: Starten von cupsd succeeded
    Dec 27 00:42:03 localhost kernel: NET: Registered protocol family 10
    Dec 27 00:42:03 localhost kernel: Disabled Privacy Extensions on device c0384d60(lo)
    Dec 27 00:42:03 localhost kernel: IPv6 over IPv4 tunneling driver
    Dec 27 00:42:03 localhost sshd:  succeeded
    Dec 27 00:42:04 localhost xinetd: Starten von xinetd succeeded
    Dec 27 00:42:04 localhost xinetd[2857]: xinetd Version 2.3.13 started with libwrap loadavg options compiled in.
    Dec 27 00:42:04 localhost xinetd[2857]: Started working: 0 available services
    Dec 27 00:42:05 localhost sendmail: Starten von sendmail succeeded
    Dec 27 00:42:05 localhost sendmail: Starten von sm-client succeeded
    Dec 27 00:42:05 localhost gpm[2894]: *** info [startup.c(95)]: 
    Dec 27 00:42:05 localhost gpm[2894]: Started gpm successfully. Entered daemon mode.
    Dec 27 00:42:05 localhost gpm[2894]: *** info [mice.c(1766)]: 
    Dec 27 00:42:05 localhost gpm[2894]: imps2: Auto-detected intellimouse PS/2
    Dec 27 00:42:05 localhost gpm: Starten von gpm succeeded
    Dec 27 00:42:06 localhost crond: Starten von crond succeeded
    Dec 27 00:42:07 localhost xfs: Starten von xfs succeeded
    Dec 27 00:42:07 localhost xfs[2924]: ignoring font path element /usr/X11R6/lib/X11/fonts/misc:unscaled (unreadable) 
    Dec 27 00:42:07 localhost xfs[2924]: ignoring font path element /usr/X11R6/lib/X11/fonts/75dpi:unscaled (unreadable) 
    Dec 27 00:42:07 localhost xfs[2924]: ignoring font path element /usr/X11R6/lib/X11/fonts/100dpi:unscaled (unreadable) 
    Dec 27 00:42:07 localhost xfs[2924]: ignoring font path element /usr/X11R6/lib/X11/fonts/Type1 (unreadable) 
    Dec 27 00:42:07 localhost anacron: Starten von anacron succeeded
    Dec 27 00:42:07 localhost atd: Starten von atd succeeded
    Dec 27 00:42:08 localhost messagebus: Starten von messagebus succeeded
    Dec 27 00:42:08 localhost cups-config-daemon: Starten von cups-config-daemon succeeded
    Dec 27 00:42:08 localhost haldaemon: Starten von haldaemon succeeded
    Dec 27 00:42:10 localhost fstab-sync[3504]: removed all generated mount points
    Dec 27 00:42:44 localhost login(pam_unix)[2976]: session opened for user root by LOGIN(uid=0)
    Dec 27 00:42:44 localhost  -- root[2976]: ROOT LOGIN ON tty1
     
  13. #11 Goodspeed, 27.12.2006
    Goodspeed

    Goodspeed Foren Gott
    Moderator

    Dabei seit:
    21.04.2004
    Beiträge:
    4.165
    Zustimmungen:
    1
    Ort:
    Dresden
    Schau mal nach dem Booten per "lsmod" ob das Modul geladen ist. Wenn nicht, dann hol das mal wie obe nbeschrieben nach und schau in Syslog (/var/log/syslog), ob hierzu etwas protokolliert wurde.
    An Deiner Stelle würde ich aber auch mal nach einem aktuelleren Kernel Ausschau halten ... denn möglicherweise wird zwar der Chip, aber nicht Deine spezielle Karte von Deinem 2.6.9er unterstützt ...
     
Thema:

CENTOS - DGE-528T GBit Netzwerkkarte wird nicht erkannt

Die Seite wird geladen...

CENTOS - DGE-528T GBit Netzwerkkarte wird nicht erkannt - Ähnliche Themen

  1. Centos 7.2.15.11 - yum install ecryptfs-utils-gui

    Centos 7.2.15.11 - yum install ecryptfs-utils-gui: Hallo ich habe hier eine alte Informationseite >>> https://www.centos.org/docs/5/html/5.4/technical-notes/ecryptfs-utils.html dort wird so die...
  2. Centosbefehle

    Centosbefehle: Hallo ich habe ein Centos 7.2.15.11 image (mit Hdclone von Miray gemacht) Ich möchte das Image auf eine existierende Ubuntu installation...
  3. Welche Paketquellen sind empfohlen? -CentOS 7.2.15.11

    Welche Paketquellen sind empfohlen? -CentOS 7.2.15.11: Hallo liebes Forum. Es scheint mir wie eine plumpe Anfängerfrage, jedoch habe ich zu dem Thema nichts sinnvolles gefunden. Ich habe CentOS...
  4. linux-firmware-nonfree in Centos 15.11 (64 Bit)

    linux-firmware-nonfree in Centos 15.11 (64 Bit): Hallo wie kann man linux-firmware-nonfree in Centos 15.11 (64 Bit) installieren?
  5. Centos 15.11 und grub anpassen

    Centos 15.11 und grub anpassen: Hallo ich habe Centos 15.11 (64 bit) Ich möchte grub anpassen und zwar so das ich nicht im Grubmenü an Stelle 0 stehe , sondern an Stelle 4 Wie...